I got one of these last Christmas. It works great, but the device has no obvious power source and now I can't find my cat. God help me when I accidently try to unsubscribe like that .. Carlo <felix@xxxxxxxxxxx> wrote in message news:20061003172911.GA4069@xxxxxxxxxxxxxx > On Mon, Oct 02, 2006 at 01:36:17PM -0400, uwcssa wrote: >> Please unsubscribe me! Thank you! >> >> >> Also, it would be better to have a message foot saying how to >> unsubscribe. > > Will this do? It's too big for a footer. > > Here's how to unsubscribe: > > First, ask your Internet Provider to mail you an Unsubscribing Kit. > Then follow these directions. > > The kit will most likely be the standard no-fault type. Depending on > requirements, System A and/or System B can be used. When operating > System A, depress lever and a plastic dalkron unsubscriber will be > dispensed through the slot immediately underneath. When you have > fastened the adhesive lip, attach connection marked by the large "X" > outlet hose. Twist the silver-coloured ring one inch below the > connection point until you feel it lock. > > The kit is now ready for use. The Cin-Eliminator is activated by the > small switch on the lip. When securing, twist the ring back to its > initial condition, so that the two orange lines meet. Disconnect. > Place the dalkron unsubscriber in the vacuum receptacle to the rear. > Activate by pressing the blue button. > > The controls for System B are located on the opposite side. The red > release switch places the Cin-Eliminator into position; it can be > adjusted manually up or down by pressing the blue manual release > button. The opening is self-adjusting. To secure after use, press the > green button, which simultaneously activates the evaporator and > returns the Cin-Eliminator to its storage position. > > You may log off if the green exit light is on over the evaporator. If > the red light is illuminated, one of the Cin-Eliminator requirements > has not been properly implemented. Press the "List Guy" call button on > the right of the evaporator. He will secure all facilities from his > control panel. > > To use the Auto-Unsub, first undress and place all your clothes in the > clothes rack. Put on the velcro slippers located in the cabinet > immediately below. Enter the shower, taking the entire kit with > you. On the control panel to your upper right upon entering you will > see a "Shower seal" button. Press to activate. A green light will then > be illuminated immediately below. On the intensity knob, select the > desired setting. Now depress the Auto-Unsub activation lever. Bathe > normally. > > The Auto-Unsub will automatically go off after three minutes unless > you activate the "Manual off" override switch by flipping it up. When > you are ready to leave, press the blue "Shower seal" release > button. The door will open and you may leave. Please remove the velcro > slippers and place them in their container. > > If you prefer the ultrasonic log-off mode, press the indicated blue > button. When the twin panels open, pull forward by rings A & B. The > knob to the left, just below the blue light, has three settings, low, > medium or high. For normal use, the medium setting is suggested. > > After these settings have been made, you can activate the device by > switching to the "ON" position the clearly marked red switch. If > during the unsubscribing operation you wish to change the settings, > place the "manual off" override switch in the "OFF" position. You may > now make the change and repeat the cycle. When the green exit light > goes on, you may log off and have lunch. Please close the door behind > you. > > > -- > ... _._. ._ ._. . _._. ._. ___ .__ ._. . .__. ._ .. ._. > Felix Finch: scarecrow repairman & rocket surgeon / felix@xxxxxxxxxxx > GPG = E987 4493 C860 246C 3B1E 6477 7838 76E9 182E 8151 ITAR license > #4933 > I've found a solution to Fermat's Last Theorem but I see I've run out of > room o > > ---------------------------(end of broadcast)--------------------------- > TIP 9: In versions below 8.0, the planner will ignore your desire to > choose an index scan if your joining column's datatypes do not > match >
