On 24/06/2016 15:24, Sahil Gandhi wrote: > Hi Steve, > > Could you please help me out? > I tried to re-read that part of user-guide but no success. > I know how to generate fingerprint but once i create new static > library out of libcrypto.a and libssl.a. > And I do generate the finger print of that new library but don't know > how to proceed further with that. > > because if i use that new library(to create executable) as it is, it > throws fingerprint mismatch error. > My sample source file has FIPS_mode_set(1) call only. > Because fipscannister.o is not compiled as 100% position independent code (and cannot legally be done so due to the bureaucratic rules of the FIPS validation), every new program linked to the FIPS enabled libcrypto.a will end up with a different fingerprint for the fipscannister. And if load address randomization is enabled in the operating system, each new run of the program will end up with a different fingerprint and thus not work. The situation is slightly better for the libcrypto.so DLL, because if load address randomization is turned off and it is ensured that libcrypto.so will load at a particular address every time, there will only be one fingerprint for each compiled libcrypto.so DLL. > On Fri, Jun 24, 2016 at 4:14 PM, Steve Marquess <marquess at openssl.com > <mailto:marquess at openssl.com>> wrote: > > On 06/24/2016 03:10 AM, Sahil Gandhi wrote: > > Hi Jakob, > > > > Could you please elaborate it? I am not getting it. > > I might missing something but I did not get it. > > > > Many Thanks Jakob for replying. > > > > -Sahil > > > > On Fri, Jun 24, 2016 at 11:57 AM, Jakob Bohm > <jb-openssl at wisemo.com <mailto:jb-openssl at wisemo.com> > > <mailto:jb-openssl at wisemo.com <mailto:jb-openssl at wisemo.com>>> wrote: > > > > On 24/06/2016 07:59, Sahil Gandhi wrote: > > > > Hi All, > > > > I have built Openssl-fips-2.0.10.tar on* RHEL Linux* > (/_*Same > > happens with Solaris 10*_/). Then I built Openssl-1.0.1p > using > > respective fips object module (i.e. > Openssl-fips-2.0.10.tar). > > > > Once I have built Openssl-1.0.1p, libcrypto.a and > libssl.a has > > been created. > > I need to join these 2 libraries and make it one. > > > > I am doing it using "ar" command as follows: > > > > ar -x libssl.a > > ar -x libcrypto.a > > > > Then combine all .o files to make third library: > > ar -r libnew.a *.o > > > > But when i use this libnew.a in my sample(contain > > FIPS_mode_set(1)), it compiles successfully but when > execute the > > executable it throws error* finger print does not > match:fips.c:232* > > > > Plz help. > > I need to combine both libaries and make it one. > > > > Any help/suggestion? > > > > > > You forgot the special link step for FIPS enabled applications, > > perhaps also some of the other required steps from the FIPS > > module users guide. > > > > See https://openssl.org/docs/fips/UserGuide-2.0.pdf. > > The FIPS module requires special build-time voodoo to satisfy the > peculiar requirements of the FIPS 140-2 validation. > Enjoy Jakob -- Jakob Bohm, CIO, Partner, WiseMo A/S. https://www.wisemo.com Transformervej 29, 2860 S?borg, Denmark. Direct +45 31 13 16 10 This public discussion message is non-binding and may contain errors. WiseMo - Remote Service Management for PCs, Phones and Embedded
