On Sat, Jan 23, 2021 at 6:43 PM Roy Spliet <nouveau@xxxxxxxxxx> wrote: > > Op 23-01-2021 om 23:18 schreef o1bigtenor: > >>>>>> > >>>>>> OK, so this is your 4k monitor. It is plugged into the *secondary* > >>>>>> GPU, and does not report any 4k@60 modes in the EDID (well, it does > >>>>>> report 4k@60 YUV 4:2:0 modes, but we don't support those in nouveau at > >>>>>> this time). Whether that's because the monitor itself doesn't support > >>>>>> HDMI 2.0, or you plugged it into your old GPU which does not support > >>>>>> HDMI 2.0, I couldn't say from just this output. What I can say is that > >>>>>> no amount of modelines will get you 4k@60 in this setup with nouveau. > >>>>> > [...] > > If you would point out a suggestion that I haven't tried - - - please? > > A quick DuckDuckGo for "Hisense 4K 60Hz only reports 30Hz" gives this > thread: https://www.coolcomputing.com/article.php?sid=4659 . No idea > whether this also applies to your 2016 model. Have you scavenged through > the TVs menu's to make sure HDMI 2.0 is explicitly enabled? What is very interesting is that the article is talking about a 43" HiSens Roku TV. At the beginning of my trouble shooting I called HiSense USA - - - found out that the software is different from that on the model sold by HiSense Canada. About 2/3rds of what is mentioned in the article - - - - well it just ain't so. Might be worth plugging a ethernet cord into the thing and trying to ssh into it to see what's hiding in the system - - - the software screen does say opensource and mentions a number of common programs including libc (and others). Hmmmmmmmm - - - - have found a pile of documents where EDID is shown to be a very error prone 'standard'. The model year listed is only one of those the companies documents indicate that the model was sold starting in 2019 and that there are 3 HDMI 2.0b inputs. It gets far more interesting! I have 2 graphics cards: card0 is an Nvidia 1050 Ti, card 1 is an Nvidia 570 there is only one HDMI port between the two cards (on card0) yet it is the HDMI interface on card 1 that has the EDID information and reads as the port is enabled. (Absolutely cannot enable the HDMI port on card0!!) In my Xorg.0.log files I find a modeline that reads like: [ 40.740] (II) modeset(G0): Supported detailed timing: [ 40.740] (II) modeset(G0): clock: 297.0 MHz Image Size: 1872 x 1053 mm [ 40.740] (II) modeset(G0): h_active: 3840 h_sync: 4016 h_sync_end 4104 h_blank_end 4400 h_border: 0 [ 40.740] (II) modeset(G0): v_active: 2160 v_sync: 2168 v_sync_end 2178 v_blanking: 2250 v_border: 0 which is somewhat similar to: Preferred Video Timing if only Block 0 is parsed: DTD 1: 3840x2160 30.000 Hz 16:9 67.500 kHz 297.000 MHz (1872 mm x 1053 mm) Hfront 176 Hsync 88 Hback 296 Hpol P Vfront 8 Vsync 10 Vback 72 Vpol P ---------------- Native Video Timing if only Block 0 is parsed: DTD 1: 3840x2160 30.000 Hz 16:9 67.500 kHz 297.000 MHz (1872 mm x 1053 mm) Hfront 176 Hsync 88 Hback 296 Hpol P Vfront 8 Vsync 10 Vback 72 Vpol P ---------------- Preferred Video Timings if Block 0 and CTA-861 Blocks are parsed: DTD 1: 3840x2160 30.000 Hz 16:9 67.500 kHz 297.000 MHz (1872 mm x 1053 mm) Hfront 176 Hsync 88 Hback 296 Hpol P Vfront 8 Vsync 10 Vback 72 Vpol P VIC 95: 3840x2160 30.000 Hz 16:9 67.500 kHz 297.000 MHz Hfront 176 Hsync 88 Hback 296 Hpol P Vfront 8 Vsync 10 Vback 72 Vpol P ---------------- Native Video Timing if Block 0 and CTA-861 Blocks are parsed: DTD 1: 3840x2160 30.000 Hz 16:9 67.500 kHz 297.000 MHz (1872 mm x 1053 mm) Hfront 176 Hsync 88 Hback 296 Hpol P Vfront 8 Vsync 10 Vback 72 Vpol P which is was the hex dump written for HDMI-1-2 (listed as on the card that has no HDMI ports) as the EDID. I really don't understand how or why this are so garbled - - - but - - - - they are. Would love to just have a usable monitor - - - - that doesn't look like its going to happen though. Suggestions? TIA _______________________________________________ Nouveau mailing list Nouveau@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/nouveau
