Hi All, I have already asked this question on the linux-rt-users mailing list and received no response, so I thought I' try here instead. I am attempting to use the rt patch set on an OpenWRT MIPS based system (ar71xx). I'm having some issues loading/using certain kernel modules, specifically for ethernet and USB support. The symptoms I am experiencing are: 1. The system will freeze completely after loading the usb modules (manually with insmod). Specifically this is after loading ehci_platform. The system appears to detect the hardware and then lock up, it is then rebooted by the watchdog a few seconds later. See below: root@OpenWrt:/# insmod /lib/modules/3.10.32/nls_base.ko root@OpenWrt:/# insmod /lib/modules/3.10.32/nls_base.procd: - root@OpenWrt:/# insmod /lib/modules/3.10.32/usb-common.ko root@OpenWrt:/# insmod /lib/modules/3.10.32/usbcore.ko [ 51.150000] usbcore: registered new interface driver usbfs [ 51.160000] usbcore: registered new interface driver hub [ 51.160000] usbcore: registered new device driver usb root@OpenWrt:/# insmod /lib/modules/3.10.32/ehci-hcd.ko [ 58.850000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver root@OpenWrt:/# insmod /lib/modules/3.10.32/ohci-hcd.ko [ 65.730000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver root@OpenWrt:/# insmod /lib/modules/3.10.32/ehci-platform.ko [ 77.830000] ehci-platform: EHCI generic platform driver [ 77.830000] ehci-platform ehci-platform: EHCI Host Controller [ 77.840000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 77.850000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 77.880000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 77.880000] hub 1-0:1.0: USB hub found [ 77.910000] hub 1-0:1.0: 1 port detected <lock up and reboot> 2. The second issue is similar but occurs when using the ethernet. I have the atheros ethernet drivers built into the kernel and can boot to a console with the interface disabled. I can even bring the interface up with ifconfig. However, the system freezes (as above) upon sending or receiving the first network packet. Investigating further and having read up on some of the debug options. I have turned on LOCKUP_DETECTOR and BOOTPARAM_SOFTLOCKUP_PANIC. Unfortunately I can't turn on the hard lockup detector since the hardware doesn't have a nmi watchdog. I also compiled in debugging symbols and enabled DEBUG_BUGVERBOSE in order to get a call trace. Here is the output of the kernel panic for the USB case above: [ 104.060000] BUG: soft lockup - CPU#0 stuck for 22s! [insmod:1053] [ 104.060000] Modules linked in: ehci_platform(+) ohci_hcd ehci_hcd usbcore usb_common nls_base pps_gpio_poll pps_core ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 compat [ 104.060000] CPU: 0 PID: 1053 Comm: insmod Not tainted 3.10.32-rt31 #1 [ 104.060000] task: 87a1d420 ti: 87044000 task.ti: 87044000 [ 104.060000] $ 0 : 00000000 0000006e 10000000 00000000 [ 104.060000] $ 4 : 00000000 013fffff 00000002 87a1d420 [ 104.060000] $ 8 : 00000001 00000004 00000010 3120706f [ 104.060000] $12 : 00000000 87b88124 00000000 3d2b7573 [ 104.060000] $16 : f0000000 10000000 8725b800 0000000a [ 104.060000] $20 : 87813a00 00000001 00000002 00000064 [ 104.060000] $24 : 00000010 8007142c [ 104.060000] $28 : 87044000 87045850 00000001 80060890 [ 104.060000] Hi : 00000011 [ 104.060000] Lo : 00000001 [ 104.060000] epc : 80068144 preempt_schedule_irq+0x40/0x80 [ 104.060000] Not tainted [ 104.060000] ra : 80060890 need_resched+0x28/0x30 [ 104.060000] Status: 1100dc03 KERNEL EXL IE [ 104.060000] Cause : 40808800 [ 104.060000] PrId : 0001974c (MIPS 74Kc) [ 104.060000] Kernel panic - not syncing: softlockup: hung tasks [ 104.060000] CPU: 0 PID: 1053 Comm: insmod Not tainted 3.10.32-rt31 #1 [ 104.060000] Stack : 00000000 00000000 00000000 00000000 80392e72 00000039 87a1d5e4 00000068 [ 104.060000] 802df1c0 80333d1b 0000041d 80392624 87a1d5e4 00000068 ffffffff 042c227f [ 104.060000] 00000068 8007a288 00000000 80077834 00000000 00000040 802e0be8 870455b4 [ 104.060000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 104.060000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 87045540 [ 104.060000] ... [ 104.060000] Call Trace: [ 104.060000] [<8006e94c>] show_stack+0x48/0x70 [ 104.060000] [<8007764c>] panic+0xcc/0x20c [ 104.060000] [<800b6110>] watchdog_timer_fn+0x16c/0x19c [ 104.060000] [<8009995c>] __run_hrtimer.isra.26+0x80/0x104 [ 104.060000] [<8009a33c>] hrtimer_interrupt+0x204/0x494 [ 104.060000] [<80070770>] c0_compare_interrupt+0x4c/0x5c [ 104.060000] [<800b69a8>] handle_irq_event_percpu+0x74/0x1e8 [ 104.060000] [<800b96e4>] handle_percpu_irq+0x54/0x84 [ 104.060000] [<800b62c0>] generic_handle_irq+0x28/0x44 [ 104.060000] [<8006be28>] do_IRQ+0x1c/0x2c [ 104.060000] [<80060820>] ret_from_irq+0x0/0x4 [ 104.060000] [<80068144>] preempt_schedule_irq+0x40/0x80 [ 104.060000] [<80060890>] need_resched+0x28/0x30 [ 104.060000] From what I can tell it looks like it gets stuck in preempt_schedule_irq, but I'm not sure why need_resched should be below that in the call stack. Does anyone have any idea what might be going on here or any experience with similar issues which may help? Any help appreciated. Regards, Rob Connolly ########################################################################################### This communication, including any attachments, is confidential. If you are not the intended recipient, you should not read it - please contact me immediately, destroy it, and do not copy or use any part of this communication or disclose anything about it. ########################################################################################### _______________________________________________ Kernelnewbies mailing list Kernelnewbies@xxxxxxxxxxxxxxxxx http://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
