On Tue, Mar 16, 2021 at 11:43:32AM -0400, Martin Gignac wrote:
> Hi,
>
> A while back I set up flowtables on my firewall, which is running
> Fedora Server 33. I defined all of my network interfaces (physical and
> virtual) as flowtable devices:
If you enable counters, the flowtable updates the conntrack table
counters. So you can consult them via conntrack -L.
See below in your flowtable definition.
> flowtable f {
> hook ingress priority filter
> devices = { tun0, bond0, dummy0, bond1.999, bond1,
> vrf-conntrackd, vrf-mgmt, enp66s0f1, enp66s0f0, enp5s0f1, enp5s0f0,
> eno4, eno3, eno2, eno1 }
counter
> }
The flowtable datapath updates the counters right before the packet
transmission.
> I then configured the forward chain to offload all IPv4/IPv6 TCP and
> UDP traffic to the flowtable:
>
> chain forward {
> type filter hook forward priority filter; policy drop;
> ip protocol { tcp, udp } flow offload @f
> ip6 nexthdr { tcp, udp } flow offload @f
> ct state established,related counter packets 0 bytes 0 accept
> ct state invalid drop
> [...] (various accept rules)
> }
>
> This seemed to be working fine until yesterday, when an IPv6 SSH
> session through an OpenVPN tunnel (terminating on the firewall)
> between my home computer and a VM at work started locking up. I would
> then start a new IPv6 SSH session to the same VM and it work fine for
> a short while, and then it would lock up as well. The lock ups would
> last a few seconds to a few minutes, and then resolve themselves
> without me doing anything. It would work for a short while, then it
> would lock up again, and so on. IPv4 sessions did not seem to be
> affected.
>
> I tcpdump'ed the incoming OpenVPN traffic on the tun0 interface while
> simultaneously tcpdump'ing on the outgoing interface towards the VM,
> and I noticed that when the lockups occurred, I would see incoming
> traffic but no outgoing traffic. So at least I eliminated issues on
> the Internet since traffic *was* coming in on the VPN.
>
> I then added a rule in my trace chain to filter for IPv6 traffic
> coming from my home computer with the source port of one of the SSH
> connections I had that kept locking up:
>
> chain trace_chain {
> type filter hook prerouting priority -301;
> ip6 saddr 2682:272:9000:6::1:10 tcp sport 41000 meta nftrace set 1
> }
>
> I ran 'nft monitor trace' and initially I didn't see anything, which I
> assumed to be normal since the ASCII diagram at
> https://wiki.nftables.org/wiki-nftables/index.php/Flowtable shows that
> traffic gets shunted to the flowtable before the prerouting hook.
> Then, the SSH session locked up again, and right before it resumed, I
> suddenly saw an entry appear in the traces, matching this rule:
>
> ct state established,related
>
> No other packet appeared UNTIL the SSH session locked up again, and
> right before it resumed once more. Can something explain this
> behavior? I don't know understand fully how flowtables work, but it
> seems to me like suddenly there are no more hits for that specific
> flow in the flowtable, and after a while the next packet in the
> session no longer bypasses the classic forwarding path. That packet
> then matches 'ct state established,related' and an established
> conntrack entry, which then puts a new flow in the flow table, and the
> subsequent packets then once again bypass the classic forwarding
> path... until it locks up again.
>
> I'm not sure where to look at this stage. I wanted to look at the
> entry in the flow table, much like one can do for conntrack sessions,
> but I couldn't find any info on the web regarding whether this is
> actually possible or not.
No way to dump the flowtable content yet, but that is doable.
> Does anybody have any flowtable troubleshooting tips for me?
Quick description of the flowtable datapath:
#1 if lookup fails (no match) => pass up (to classic forwarding path)
#2 if packet exceeds mtu => pass up
#3 tcp fin or rst => pass up
... from this point on packet follows the flowtable datapath
#4 nat
#5 decrement ttl
#6 update counters (if enabled)
#7 xmit
The flowtable entry stays in the flowtable for 30 seconds, if no
packets are seen, the entry expires and packets go back to classic
forwarding path.
Your trace rule shows no packets being passed up until the connection
resumes from the stall.
Can you see the flowtable counters being updated?
> Thanks,
> -Martin
>
> P.S. The OS is Fedora Server 33 (kernel 5.10.17-200.fc33.x86_64) with
> a manually compiled nftables (v0.9.8).
This kernel contains 8d6bca156e47 ("netfilter: flowtable: fix tcp and
udp header checksum update"), so this might be a different issue.
