|
Hi, I successfully configured (I think) a bridging
firewall using Script provided in David Whitmarsh's how too at http://www.sparkle-cc.co.uk/firewall/firewall.html
I have a few questions as I am trying VERY hard to never have to see a Windows
XXAnything disc again.
1.) I do not see anything other than IPTables
starting up and learning.......in /var/log/messages. I have unremarked kernal*
to point to /var/log/messages. I think the only logging being done is if a DOS
occurrs. Based on his script, how do I enable more or any logging that will show
me a little or alot of something? :)
2.) I have 2 NIC's both public (which is why I
choose to bridge) In this script, I enabled the option to allow remote access
from my LAN. However I cannot even ping.....from inside the LAN ,the specified
address in the script to the firewall.
3.) The firewall cannot ping outside the LAN (which
I could care less) but Im getting messages when the script runs that the machine
cannot lookup or resolve FQDN's specified to be blocked.
Any help is greatly appreciated. Below is the
script after I modified it. I am using REDHat 8.0 with IPTables Bridg Util
Patch.
Tim Roberts
techlists@dsslink.net
#!/bin/sh
#
# rc.firewall - Initial SIMPLE IP Firewall test script for 2.4.x
#
# Author: David Whitmarsh
# (c) 2001, 2002 Sparkle Computer Co ltd.
# based on rc.firewall by Oskar Andreasson <blueflux@koffein.net>
# parts (c) of BoingWorld.com, use at your own risk,
# do whatever you please with
# it as long as you don't distribute this without due credits to
# BoingWorld.com and Sparkle Computer Co Ltd
#
###########
# Configuration options, these will speed you up getting this script to
# work with your own setup.
#
# your LAN's IP range and localhost IP. /24 means to only use the first 24
# bits of the 32 bit IP adress. the same as netmask 255.255.255.0
#
# BR_IP is used to access the firewall accross the network
# For maxium security don't set one up - but then you must do
# everything directly on the firewall.
BR_IP=65.173.10.254
BR_IFACE=br0
LAN_BCAST_ADDRESS=65.173.13.255
INTERNAL_ADDRESS_RANGE=65.173.120.0/22
INET_IFACE="eth1"
LAN_IFACE="eth0"
LO_IFACE="lo"
LO_IP="127.0.0.1"
IPTABLES="/sbin/iptables"
#########
# Load all required IPTables modules
#
#
# Needed to initially load modules
#
/sbin/depmod -a
#
# Adds some iptables targets like LOG, REJECT
#
/sbin/modprobe ipt_LOG
/sbin/modprobe ipt_REJECT
#
# Support for connection tracking of FTP and IRC.
#
/sbin/modprobe ip_conntrack_ftp
/sbin/modprobe ip_conntrack_irc
#
# Take down the interfaces before setting up the bridge
#
ifdown $INET_IFACE
ifdown $LAN_IFACE
ifconfig $INET_IFACE 0.0.0.0
ifconfig $LAN_IFACE 0.0.0.0
# Clean up for a restart
$IPTABLES -F
$IPTABLES -X
#
# Set default policies for the INPUT, FORWARD and OUTPUT chains
#
$IPTABLES -P INPUT DROP
$IPTABLES -P OUTPUT ACCEPT
$IPTABLES -P FORWARD DROP
# Our interfaces don't have IP addresses so we have to start with the mangle
# PREROUTING table
$IPTABLES -t mangle -P PREROUTING DROP
# Now we are pretty secure, let's start the bridge
# This will create a new interface
brctl addbr $BR_IFACE
# and add the interfaces to it
brctl addif $BR_IFACE $INET_IFACE
brctl addif $BR_IFACE $LAN_IFACE
# make us visible to the network again (optional)
if [ "$BR_IP" != "" ] ; then
ifconfig $BR_IFACE $BR_IP
else
# otherwise we must at least bring the interface up for the bridge to work.
ifconfig $BR_IFACE up
fi
# Block obvious spoofs
$IPTABLES -t mangle -A PREROUTING -s 192.168.0.0/16 -j DROP
$IPTABLES -t mangle -A PREROUTING -s 10.0.0.0/8 -j DROP
$IPTABLES -t mangle -A PREROUTING -s 172.16.0.0/12 -j DROP
# Accept internal packets on the internal i/f
$IPTABLES -t mangle -A PREROUTING -i $LAN_IFACE -s $INTERNAL_ADDRESS_RANGE -j ACCEPT
# Accept external packets on the external i/f
$IPTABLES -t mangle -A PREROUTING -i $INET_IFACE ! -s $INTERNAL_ADDRESS_RANGE -j ACCEPT
#
# Accept the packets we actually want to forward
#
$IPTABLES -A FORWARD -p ALL -s $INTERNAL_ADDRESS_RANGE -j ACCEPT
$IPTABLES -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT
$IPTABLES -A FORWARD -m limit --limit 3/minute --limit-burst 3 -j LOG --log-level 7 --log-prefix "IPT FORWARD packet died: "
#
# Create separate chains for ICMP, TCP and UDP to traverse
#
$IPTABLES -N icmp_packets
#
# ICMP rules
#
$IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 0 -j ACCEPT # echo reply
$IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 3 -j ACCEPT # dest unreachable
$IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 5 -j ACCEPT # redirect
$IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 11 -j ACCEPT # time exceeded
$IPTABLES -A FORWARD -p ICMP -j icmp_packets
#
# UDP ports
#
$IPTABLES -N udpincoming_packets
$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 53 -j ACCEPT # DNS
$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 123 -j ACCEPT # ntp
#$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 2074 -j ACCEPT # speakfreely
#$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 4000 -j ACCEPT #icq
$IPTABLES -A FORWARD -p UDP -j udpincoming_packets
#
$IPTABLES -N tcp_packets
#
# The allowed chain for TCP connections
#
$IPTABLES -N allowed
$IPTABLES -A allowed -p TCP --syn -j ACCEPT
$IPTABLES -A allowed -p TCP -m state --state ESTABLISHED,RELATED -j ACCEPT
$IPTABLES -A allowed -p TCP -j DROP
# TCP rules
#
#
# Bad TCP packets we don't want
#
$IPTABLES -A tcp_packets -p tcp ! --syn -m state --state NEW -j LOG --log-prefix "New not syn:"
$IPTABLES -A tcp_packets -p tcp ! --syn -m state --state NEW -j DROP
$IPTABLES -A tcp_packets -p TCP -s 0/0 -d springfield.sparkle-cc.co.uk --dport 80 -j allowed # smtp
$IPTABLES -A tcp_packets -p TCP -s 0/0 -d lisa.sparkle-cc.co.uk --dport 6346 -j allowed # gnutella
$IPTABLES -A tcp_packets -p TCP -s 0/0 -d springfield.sparkle-cc.co.uk --dport 25 -j allowed # smtp
$IPTABLES -A FORWARD -p TCP -j tcp_packets
#
# Input to the firewall itself. Leave these out if you don't want the firewall
# to be visible on the network at all.
# Note that the PREROUTING restrictions above mean that only packets form inside
# the firewall can fulfill the source condition. So the firewall machine should not be
# visible to the internet.
#
$IPTABLES -A INPUT -p ALL -i $BR_IFACE -s $INTERNAL_ADDRESS_RANGE -d $LAN_BCAST_ADDRESS -j ACCEPT
$IPTABLES -A INPUT -p ALL -i $BR_IFACE -s $INTERNAL_ADDRESS_RANGE -d $BR_IP -j ACCEPT
# But you *will* need this
$IPTABLES -A INPUT -p ALL -i $LO_IFACE -d $LO_IP -j ACCEPT
$IPTABLES -A INPUT -m limit --limit 3/minute --limit-burst 3 -j LOG --log-level 7 --log-prefix "IPT INPUT packet died: "
#
# OUTPUT chain
#
$IPTABLES -A OUTPUT -p tcp ! --syn -m state --state NEW -j LOG --log-prefix "New not syn:"
$IPTABLES -A OUTPUT -p tcp ! --syn -m state --state NEW -j DROP
$IPTABLES -A OUTPUT -p ALL -s $LO_IP -j ACCEPT
$IPTABLES -A OUTPUT -p ALL -s $BR_IP -j ACCEPT
$IPTABLES -A OUTPUT -m limit --limit 3/minute --limit-burst 3 -j LOG --log-level 7 --log-prefix "IPT OUTPUT packet died: "
|
