Four misspellings and a missing pronoun. Signed-off-by: Jeremy Sowden <jeremy@xxxxxxxxxx> --- conntrack.8 | 2 +- conntrackd.conf.5 | 4 ++-- nfct.8 | 2 +- src/conntrack.c | 2 +- 4 files changed, 5 insertions(+), 5 deletions(-) diff --git a/conntrack.8 b/conntrack.8 index 6fbb41fe81fc..031eaa4e9fef 100644 --- a/conntrack.8 +++ b/conntrack.8 @@ -180,7 +180,7 @@ Specify the conntrack mark. Optionally, a mask value can be specified. In "\-\-update" mode, this mask specifies the bits that should be zeroed before XORing the MARK value into the ctmark. Otherwise, the mask is logically ANDed with the existing mark before the -comparision. In "\-\-create" mode, the mask is ignored. +comparison. In "\-\-create" mode, the mask is ignored. .TP .BI "-l, --label " "LABEL" Specify a conntrack label. diff --git a/conntrackd.conf.5 b/conntrackd.conf.5 index a73c3f715df9..50d7b989a942 100644 --- a/conntrackd.conf.5 +++ b/conntrackd.conf.5 @@ -52,7 +52,7 @@ You should consider this file as case-sensitive. Empty lines and lines starting with the '#' character are ignored. Before starting to develop a new configuration, you may want to learn the -concepts behind this technlogy at +concepts behind this technology at \fIhttp://conntrack-tools.netfilter.org/manual.html\fP. There are complete configuration examples at the end of this man page. @@ -630,7 +630,7 @@ filter-sets in positive or negative logic depending on your needs. You can select if \fBconntrackd(8)\fP filters the event messages from user-space or kernel-space. The kernel-space event filtering saves some CPU cycles by avoiding the copy of the event message from kernel-space to -user-space. The kernel-space event filtering is prefered, however, you require +user-space. The kernel-space event filtering is preferred, however, you require a \fBLinux kernel >= 2.6.29\fP to filter from kernel-space. The syntax for this section is: \fBFilter From <from> { }\fP. diff --git a/nfct.8 b/nfct.8 index c38bdbe45788..b130a8804c4a 100644 --- a/nfct.8 +++ b/nfct.8 @@ -8,7 +8,7 @@ nfct \- command line tool to configure with the connection tracking system .BR "nfct command subsystem [parameters]" .SH DESCRIPTION .B nfct -is the command line tool that allows to configure the Connection Tracking +is the command line tool that allows you to configure the Connection Tracking System. .SH COMMANDS .TP diff --git a/src/conntrack.c b/src/conntrack.c index 77c60b9391a5..f9758d78d39b 100644 --- a/src/conntrack.c +++ b/src/conntrack.c @@ -538,7 +538,7 @@ static const char usage_parameters[] = "Common parameters and options:\n" " -s, --src, --orig-src ip\t\tSource address from original direction\n" " -d, --dst, --orig-dst ip\t\tDestination address from original direction\n" - " -r, --reply-src ip\t\tSource addres from reply direction\n" + " -r, --reply-src ip\t\tSource address from reply direction\n" " -q, --reply-dst ip\t\tDestination address from reply direction\n" " -p, --protonum proto\t\tLayer 4 Protocol, eg. 'tcp'\n" " -f, --family proto\t\tLayer 3 Protocol, eg. 'ipv6'\n" -- 2.40.1
