Hi Florian
i recheck and libxt_DNAT.so is symlink to libxt_NAT.so
and i try :
iptables v1.8.9 (nf_tables)
Usage: iptables -[ACD] chain rule-specification [options]
iptables -I chain [rulenum] rule-specification [options]
iptables -R chain rulenum rule-specification [options]
iptables -D chain rulenum [options]
iptables -[LS] [chain [rulenum]] [options]
iptables -[FZ] [chain] [options]
iptables -[NX] chain
iptables -E old-chain-name new-chain-name
iptables -P chain target [options]
iptables -h (print this help information)
Commands:
Either long or short options are allowed.
--append -A chain Append to chain
--check -C chain Check for the existence of a rule
--delete -D chain Delete matching rule from chain
--delete -D chain rulenum
Delete rule rulenum (1 = first) from chain
--insert -I chain [rulenum]
Insert in chain as rulenum (default 1=first)
--replace -R chain rulenum
Replace rule rulenum (1 = first) in chain
--list -L [chain [rulenum]]
List the rules in a chain or all chains
--list-rules -S [chain [rulenum]]
Print the rules in a chain or all chains
--flush -F [chain] Delete all rules in chain or all chains
--zero -Z [chain [rulenum]]
Zero counters in chain or all chains
--new -N chain Create a new user-defined chain
--delete-chain
-X [chain] Delete a user-defined chain
--policy -P chain target
Change policy on chain to target
--rename-chain
-E old-chain new-chain
Change chain name, (moving any references)
Options:
--ipv4 -4 Nothing (line is ignored by ip6tables-restore)
--ipv6 -6 Error (line is ignored by iptables-restore)
[!] --protocol -p proto protocol: by number or name, eg. `tcp'
[!] --source -s address[/mask][...]
source specification
[!] --destination -d address[/mask][...]
destination specification
[!] --in-interface -i input name[+]
network interface name ([+] for wildcard)
--jump -j target
target for rule (may load target extension)
--goto -g chain
jump to chain with no return
--match -m match
extended match (may load extension)
--numeric -n numeric output of addresses and ports
[!] --out-interface -o output name[+]
network interface name ([+] for wildcard)
--table -t table table to manipulate (default: `filter')
--verbose -v verbose mode
--wait -w [seconds] maximum wait to acquire xtables lock before give up
--line-numbers print line numbers when listing
--exact -x expand numbers (display exact values)
[!] --fragment -f match second or further fragments only
--modprobe=<command> try to insert modules using this command
--set-counters -c PKTS BYTES set the counter during insert/append
[!] --version -V print package version.
and show help .
same here i test with both : iptables-nft and iptables-legacy
restore to version 1.8.8 and all is fine.
i will try to rebuild and recheck if same is happen will update you.
m.
> On 2 Mar 2023, at 12:43, Florian Westphal <fw@xxxxxxxxx> wrote:
>
> Martin Zaharinov <micron10@xxxxxxxxx> wrote:
>> iptables -t nat -A PREROUTING -d 100.91.1.238/32 -i bond0 -p tcp --dport
>> 7878 -j DNAT --to-destination 10.240.241.99:7878
>> iptables v1.8.9 (legacy): unknown option "--to-destination"
>> Try `iptables -h' or 'iptables --help' for more information.
>
> Looks like a problem with your iptables installation which can't find
> libxt_DNAT.so? In v1.8.9 this should be a symlink to libxt_NAT.so.
>
> If you run 'iptables -j DNAT --help' and it doesn't say
>
> "DNAT target options:" at the end then it very much looks like a
> problem with your iptables installation and not the kernel.
>
>> try with kernel 6.1.11 6.1.12 6.1.13
>
> Tested iptables-nft and iptables-legacy on 1.8.9 with kernel 6.1.14, no problems.
>
> There were no significant kernel changes in this area that I know of in
> 6.1 either.
