On Mon, 26 Jul 2021, Akshat Kakkar wrote: > MCU is using IP only to dial to VC1 and not hostname. > > I went through packet capture and find everything in line with the > standard. Just that it is sending "CS : Call Proceeding" packet which > is an optional packet but it is part of standard. > I can share pcap file if needed. Could you enable dynamic debugging in the kernel and enable it for the nf_conntrack_h323 module? Then please repeate the testing with the working and not working VCs and send the generated kernel debug log messages. Best regards, Jozsef > On Mon, Jul 26, 2021 at 2:11 AM Jozsef Kadlecsik <kadlec@xxxxxxxxxxxxx> wrote: > > > > Hello, > > > > On Sat, 24 Jul 2021, Akshat Kakkar wrote: > > > > > I have 2 vc endpoints VC1 (Make:Panasonic, IP:10.1.1.11), > > > VC2(make:Polycom,IP: 10.1.1.12) and 1 MCU (172.16.1.100). > > > > > > There is a Linux firewall between VCs and MCU. > > > > > > There is one to one nat configured for these 2 VCs (10.1.1.11 <--> > > > 172.16.1.110, 10.1.1.12 <--> 172.16.1.120) > > > There is no natting for MCU IP as it is routable. > > > > > > nf_nat_h323 and nf_conntrack_h323 module is enabled in the firewall. > > > > > > When VC1 and VC2 initiate call to MCU, everything works fine. Video > > > call is successful for both VC1 and VC2. h245 IP address for tcp in > > > h225: CS connect packet is correctly replaced by the natted IP. > > > > > > However, when there is a dial out from MCU to VCs (i.e. MCU initiate > > > call to the natted IP (i.e. 172.16.1.110 and 172.16.1.120 of VCs), > > > natting works fine but h245 IP address for tcp in h225:CS is replaced > > > correctly only for VC2 and not for VC1. For VC1, it is still its > > > actual IP (i.e. 10.1.1.12 and not 172.16.1.120). > > > > > > Because of this, video call is successful only with VC2 and not with > > > VC1, when initiated from MCU. I tried with another panasonic VC > > > hardware, there was no change. > > > > > > Further packet dump analysis showed that for VC1, there are 3 h225 > > > packets (setup, call proceeding and alert) before Connect message but > > > for VC2 there are only 2 h225 packets (setup and alert) before connect > > > message. > > > > > > Is there a bug in nf_nat_h323 module or am I missing something? > > > > It can be a bug/incompatibility with the H.323 implementation in the > > Panasonic device. However, first I'd make sure the MCU does not use > > hostname for VC1 instead of its IP address. Hostnames in the calls are not > > supported. > > > > Best regards, > > Jozsef > > - > > E-mail : kadlec@xxxxxxxxxxxxxxxxx, kadlecsik.jozsef@xxxxxxxxx > > PGP key : https://wigner.hu/~kadlec/pgp_public_key.txt > > Address : Wigner Research Centre for Physics > > H-1525 Budapest 114, POB. 49, Hungary > - E-mail : kadlec@xxxxxxxxxxxxxxxxx, kadlecsik.jozsef@xxxxxxxxx PGP key : https://wigner.hu/~kadlec/pgp_public_key.txt Address : Wigner Research Centre for Physics H-1525 Budapest 114, POB. 49, Hungary
