Re: Network namespace, ipvlan and IPVS source NAT

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Oct 20, 2020 at 11:01 AM Julian Anastasov <ja@xxxxxx> wrote:
>
>
>         Hello,
>
> On Tue, 20 Oct 2020, Damien Claisse wrote:
>
> > I'm trying to understand a limitation in ipvlan/netfilter that prevents doing routed IPVS with source NAT inside a namespace.
> >
> > Setup is the following: there is an "lvs" namespace, with an ipvlan interface (in l3 mode) moved to this namespace, linked to physical interface. Goal is to isolate load balanced traffic in a separate namespace.
> > This setup is working flawlessly with l3 routed IPIP encapsulation, but I also have a use case for applications that don't support encapsulation, hence the need to do l3 routed load balancing with source NAT.
> > Issue is that if I put iptables NAT rule in namespace using ipvs module, nothing happens, packet is forwarded but source IP is not translated. It seems like netfilter is blind to ipvlan l3 traffic. I also tried using "l3s" mode that should to go through netfilter, but in that case, packets for virtual IPs are rejected with a TCP reset. Virtual IPs in namespace seem not visible to this mode.
> >
> > I'm wondering what would be the best way to make it happen:
> > - patch ipvlan to lookup for VIPs in namespaces
> > - patch netfilter ipvs NAT module to translate in root namespace
> > - any other better idea is welcome
> >
> > Please find below commands to reproduce the issue. In this example physical load balancer interface is enp4s0, virtual IP is 192.168.42.1 (to be exported by a routing protocol, or route manually added to a client in same subnet as load balancer for testing), load balancer IP is 192.168.10.10, and real server IP is 192.168.20.20
> >
> > - In root namespace:
> > ip netns add lvs
> > ip link add ipvlan0 link enp4s0 type ipvlan mode l3s
> > ip link set ipvlan0 up
> > ip link set ipvlan0 netns lvs
> >
> > - In lvs namespace (ip netns exec lvs bash):
> > ip addr add 192.168.42.1/32 dev ipvlan0
> > ip route add default via 192.168.10.10 dev ipvlan0 onlink
> > ipvsadm -A -t 192.168.42.1:80 -s rr
> > ipvsadm -a -t 192.168.42.1:80 -r 192.168.20.20:80 -m
> > iptables -t nat -A POSTROUTING -m ipvs --vaddr 192.168.42.1/24 --vport 80 -j SNAT --to-source 192.168.10.10
>
>         Make sure /proc/sys/net/ipv4/vs/conntrack is set to 1
> to allow IPVS to keep the netfilter conntracks for its
> packets. This is supported with the CONFIG_IP_VS_NFCT=y
> kernel option.
>
> > What I'd expect: a packet outgoing from enp4s0 with source IP 192.168.10.10 and destination IP 192.168.20.20
> > What I see from a test client:
> > - in l3 mode: a packet outgoing from enp4s0 with source client IP address and destination 192.168.20.20 (hence missing source NAT). I also don't see any conntrack event when doing conntrack -E
> > - in l3s mode: connection reset sent to client. While reading l3s implementation, I wonder where route lookup is done in ipvlan_l3_rcv, it seems that namespaces' virtual IP addresses are not visible during this lookup, hence the TCP RST.
>
Unfortunately iptables and IPvlan don't do well together, especially
the L3* modes. L3s mode is a little better but please keep in mind
iptables functionality that involves "forwarding" path, is simply not
compatible with IPvlan L3* modes. Your best bet is to use L2 mode and
perform all IPtables operations inside the namespace if possible.

Regards,
--mahesh..

> Regards
>
> --
> Julian Anastasov <ja@xxxxxx>
>




[Index of Archives]     [Netfitler Users]     [Berkeley Packet Filter]     [LARTC]     [Bugtraq]     [Yosemite Forum]

  Powered by Linux