On Thu, Jan 26, 2012 at 09:46:41PM -0500, Quentin Aebischer wrote: > Sorry, forgot to add conntrackd.conf example and README files ... > > From : Quentin Aebischer <quentin.aebischer@xxxxxxxxxxxxxx> > > Example file conntrackd.conf and README for TIPC implementation of > the conntrackd daemon. > > Signed-off-by: Quentin Aebischer <quentin.aebischer@xxxxxxxxxxxxxx> > --- > doc/sync/tipc/README | 13 ++ I'd appreciate if you can send me a patch for the doc/manual/conntrack-tools.tmpl instead. I suggest you to add a small paragraph at "Other configuration options". > doc/sync/tipc/conntrackd.conf | 454 > +++++++++++++++++++++++++++++++++++++++++ > 2 files changed, 467 insertions(+), 0 deletions(-) > > diff --git a/doc/sync/tipc/README b/doc/sync/tipc/README > new file mode 100644 > index 0000000..e7afcc7 > --- /dev/null > +++ b/doc/sync/tipc/README > @@ -0,0 +1,13 @@ > +Installation instructions : > + > +TIPC is a built-in kernel module since kernel version 2.6.35 ; > please make sure your using a => 2.6.35 kernel with TIPC 2.0, as > this patch has not been tested with older versions of the protocol > yet. > + > +For easy and fast configuration, you must install the TIPC utilies > v2.0.0, available from sources here : > + > + git://tipc.git.sourceforge.net/gitroot/tipc/tipcutils (branch > tipcutils2.0) > + > +or by using aptitude on debian distributions : > + > + sudo apt-get install tipcutils > + > +For further details on installation, node and network > configuration, please refer to the online documentation : http://tipc.sourceforge.net/doc/tipc_2.0_users_guide.html#installation. > diff --git a/doc/sync/tipc/conntrackd.conf b/doc/sync/tipc/conntrackd.conf > new file mode 100644 > index 0000000..71946ec > --- /dev/null > +++ b/doc/sync/tipc/conntrackd.conf > @@ -0,0 +1,454 @@ > +# > +# Synchronizer settings > +# > +Sync { > + Mode NOTRACK { Better, add this example to the existing notrack file. More specifically, this part below just after the commented UDP and Multicast examples. > + TIPC { > + # > + # Name of the other TIPC port in the cluster (in the form type:instance) Please, break lines at 80 char, btw. > + # > + TIPC_Destination_Name 1000:51 > + > + # > + # Name of the local TIPC port (used to listen to events) > + # > + TIPC_Name 1000:50 > + > + # > + # The name of the TIPC configured interface that you are going to use > + # to send synchronization messages. > + # > + Interface eth0 > + > + # > + # The importance of the TIPC messages sent (the more important > this is, the more packets will be enabled to queue up on the slave) > + # This should be set to High or Critical to avoid congestion on > the receiver side. > + # (possible values : TIPC_LOW_IMPORTANCE, TIPC_MEDIUM_IMPORTANCE, > TIPC_HIGH_IMPORTANCE, TIPC_CRITICAL_IMPROTANCE) > + # > + TIPC_Message_Importance TIPC_CRITICAL_IMPORTANCE > + > + # > + # Current TIPC implementation doesnt allow checksumming > + } Thanks Quentin. -- To unsubscribe from this list: send the line "unsubscribe netfilter-devel" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
