The patch titled
cris: fix a build error in drivers/tty/serial/crisv10.c
has been removed from the -mm tree. Its filename was
cris-fix-a-build-error-in-drivers-tty-serial-crisv10c.patch
This patch was dropped because it was merged into mainline or a subsystem tree
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: cris: fix a build error in drivers/tty/serial/crisv10.c
From: WANG Cong <xiyou.wangcong@xxxxxxxxx>
drivers/tty/serial/crisv10.c:4453: error: 'if_ser0' undeclared (first use in this function): 2 errors in 2 logs
v3.1-rc4/cris/cris-allmodconfig v3.1-rc4/cris/cris-allyesconfig
drivers/tty/serial/crisv10.c:4453: error: (Each undeclared identifier is reported only once: 2 errors in 2 logs
v3.1-rc4/cris/cris-allmodconfig v3.1-rc4/cris/cris-allyesconfig
drivers/tty/serial/crisv10.c:4453: error: for each function it appears in.): 2 errors in 2 logs
v3.1-rc4/cris/cris-allmodconfig v3.1-rc4/cris/cris-allyesconfig
"if_ser0" is a typo, it should be "if_serial_0".
Signed-off-by: WANG Cong <xiyou.wangcong@xxxxxxxxx>
Cc: Mikael Starvik <starvik@xxxxxxxx>
Cc: Jesper Nilsson <jesper.nilsson@xxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/tty/serial/crisv10.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff -puN drivers/tty/serial/crisv10.c~cris-fix-a-build-error-in-drivers-tty-serial-crisv10c drivers/tty/serial/crisv10.c
--- a/drivers/tty/serial/crisv10.c~cris-fix-a-build-error-in-drivers-tty-serial-crisv10c
+++ a/drivers/tty/serial/crisv10.c
@@ -4450,7 +4450,7 @@ static int __init rs_init(void)
#if defined(CONFIG_ETRAX_RS485)
#if defined(CONFIG_ETRAX_RS485_ON_PA)
- if (cris_io_interface_allocate_pins(if_ser0, 'a', rs485_pa_bit,
+ if (cris_io_interface_allocate_pins(if_serial_0, 'a', rs485_pa_bit,
rs485_pa_bit)) {
printk(KERN_CRIT "ETRAX100LX serial: Could not allocate "
"RS485 pin\n");
@@ -4459,7 +4459,7 @@ static int __init rs_init(void)
}
#endif
#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
- if (cris_io_interface_allocate_pins(if_ser0, 'g', rs485_pa_bit,
+ if (cris_io_interface_allocate_pins(if_serial_0, 'g', rs485_pa_bit,
rs485_port_g_bit)) {
printk(KERN_CRIT "ETRAX100LX serial: Could not allocate "
"RS485 pin\n");
_
Patches currently in -mm which might be from xiyou.wangcong@xxxxxxxxx are
origin.patch
cris-lower-the-printk-level-in-cris-serial-driver.patch
kexec-remove-kmsg_dump_kexec.patch
--
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
