The patch titled gpio: adp5588-gpio: support interrupt controller has been added to the -mm tree. Its filename is gpio-adp5588-gpio-support-interrupt-controller.patch Before you just go and hit "reply", please: a) Consider who else should be cc'ed b) Prefer to cc a suitable mailing list as well c) Ideally: find the original patch on the mailing list and do a reply-to-all to that, adding suitable additional cc's *** Remember to use Documentation/SubmitChecklist when testing your code *** See http://userweb.kernel.org/~akpm/stuff/added-to-mm.txt to find out what to do about this The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/ ------------------------------------------------------ Subject: gpio: adp5588-gpio: support interrupt controller From: Michael Hennerich <michael.hennerich@xxxxxxxxxx> Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only level sensitive interrupts are supported. Interrupts provided by this irq_chip must be requested using request_threaded_irq(). Signed-off-by: Michael Hennerich <michael.hennerich@xxxxxxxxxx> Signed-off-by: Mike Frysinger <vapier@xxxxxxxxxx> Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx> --- drivers/gpio/Kconfig | 7 drivers/gpio/adp5588-gpio.c | 252 +++++++++++++++++++++++++++++++++- include/linux/i2c/adp5588.h | 1 3 files changed, 253 insertions(+), 7 deletions(-) diff -puN drivers/gpio/Kconfig~gpio-adp5588-gpio-support-interrupt-controller drivers/gpio/Kconfig --- a/drivers/gpio/Kconfig~gpio-adp5588-gpio-support-interrupt-controller +++ a/drivers/gpio/Kconfig @@ -284,6 +284,13 @@ config GPIO_ADP5588 To compile this driver as a module, choose M here: the module will be called adp5588-gpio. +config GPIO_ADP5588_IRQ + bool "Interrupt controller support for ADP5588" + depends on GPIO_ADP5588=y + help + Say yes here to enable the adp5588 to be used as an interrupt + controller. It requires the driver to be built in the kernel. + comment "PCI GPIO expanders:" config GPIO_CS5535 diff -puN drivers/gpio/adp5588-gpio.c~gpio-adp5588-gpio-support-interrupt-controller drivers/gpio/adp5588-gpio.c --- a/drivers/gpio/adp5588-gpio.c~gpio-adp5588-gpio-support-interrupt-controller +++ a/drivers/gpio/adp5588-gpio.c @@ -1,8 +1,8 @@ /* * GPIO Chip driver for Analog Devices - * ADP5588 I/O Expander and QWERTY Keypad Controller + * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller * - * Copyright 2009 Analog Devices Inc. + * Copyright 2009-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -13,21 +13,50 @@ #include <linux/init.h> #include <linux/i2c.h> #include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/irq.h> #include <linux/i2c/adp5588.h> + /* Configuration Register1 */ +#define AUTO_INC (1 << 7) +#define GPIEM_CFG (1 << 6) +#define OVR_FLOW_M (1 << 5) +#define INT_CFG (1 << 4) +#define OVR_FLOW_IEN (1 << 3) +#define K_LCK_IM (1 << 2) +#define GPI_IEN (1 << 1) +#define KE_IEN (1 << 0) + +/* Interrupt Status Register */ +#define GPI_INT (1 << 1) +#define KE_INT (1 << 0) + #define DRV_NAME "adp5588-gpio" #define MAXGPIO 18 #define ADP_BANK(offs) ((offs) >> 3) #define ADP_BIT(offs) (1u << ((offs) & 0x7)) +/* + * Early pre 4.0 Silicon required to delay readout by at least 25ms, + * since the Event Counter Register updated 25ms after the interrupt + * asserted. + */ +#define WA_DELAYED_READOUT_REVID(rev) ((rev) < 4) + struct adp5588_gpio { struct i2c_client *client; struct gpio_chip gpio_chip; struct mutex lock; /* protect cached dir, dat_out */ + struct mutex irq_lock; /* P: IRQ */ unsigned gpio_start; + unsigned irq_base; uint8_t dat_out[3]; uint8_t dir[3]; + uint8_t int_lvl[3]; + uint8_t int_en[3]; + uint8_t irq_mask[3]; + uint8_t irq_stat[3]; }; static int adp5588_gpio_read(struct i2c_client *client, u8 reg) @@ -125,6 +154,200 @@ static int adp5588_gpio_direction_output return ret; } +#ifdef CONFIG_GPIO_ADP5588_IRQ +static int adp5588_gpio_to_irq(struct gpio_chip *chip, unsigned off) +{ + struct adp5588_gpio *dev = + container_of(chip, struct adp5588_gpio, gpio_chip); + return dev->irq_base + off; +} + +static void adp5588_irq_bus_lock(unsigned int irq) +{ + struct adp5588_gpio *dev = get_irq_chip_data(irq); + mutex_lock(&dev->irq_lock); +} + +static void adp5588_irq_bus_sync_unlock(unsigned int irq) +{ + struct adp5588_gpio *dev = get_irq_chip_data(irq); + int i; + + for (i = 0; i <= ADP_BANK(MAXGPIO); i++) + if (dev->int_en[i] ^ dev->irq_mask[i]) { + dev->int_en[i] = dev->irq_mask[i]; + adp5588_gpio_write(dev->client, GPIO_INT_EN1 + i, + dev->int_en[i]); + } + + mutex_unlock(&dev->irq_lock); +} + +static void adp5588_irq_mask(unsigned int irq) +{ + struct adp5588_gpio *dev = get_irq_chip_data(irq); + unsigned gpio = irq - dev->irq_base; + + dev->irq_mask[ADP_BANK(gpio)] &= ~ADP_BIT(gpio); +} + +static void adp5588_irq_unmask(unsigned int irq) +{ + struct adp5588_gpio *dev = get_irq_chip_data(irq); + unsigned gpio = irq - dev->irq_base; + + dev->irq_mask[ADP_BANK(gpio)] |= ADP_BIT(gpio); +} + +static int adp5588_irq_set_type(unsigned int irq, unsigned int type) +{ + struct adp5588_gpio *dev = get_irq_chip_data(irq); + uint16_t gpio = irq - dev->irq_base; + unsigned bank, bit; + + if ((type & IRQ_TYPE_EDGE_BOTH)) { + dev_err(&dev->client->dev, "irq %d: unsupported type %d\n", + irq, type); + return -EINVAL; + } + + bank = ADP_BANK(gpio); + bit = ADP_BIT(gpio); + + if (type & IRQ_TYPE_LEVEL_HIGH) + dev->int_lvl[bank] |= bit; + else if (type & IRQ_TYPE_LEVEL_LOW) + dev->int_lvl[bank] &= ~bit; + else + return -EINVAL; + + might_sleep(); + + adp5588_gpio_direction_input(&dev->gpio_chip, gpio); + adp5588_gpio_write(dev->client, GPIO_INT_LVL1 + bank, + dev->int_lvl[bank]); + + return 0; +} + +static struct irq_chip adp5588_irq_chip = { + .name = "adp5588", + .mask = adp5588_irq_mask, + .unmask = adp5588_irq_unmask, + .bus_lock = adp5588_irq_bus_lock, + .bus_sync_unlock = adp5588_irq_bus_sync_unlock, + .set_type = adp5588_irq_set_type, +}; + +static int adp5588_gpio_read_intstat(struct i2c_client *client, u8 *buf) +{ + int ret = i2c_smbus_read_i2c_block_data(client, GPIO_INT_STAT1, 3, buf); + + if (ret < 0) + dev_err(&client->dev, "Read INT_STAT Error\n"); + + return ret; +} + +static irqreturn_t adp5588_irq_handler(int irq, void *devid) +{ + struct adp5588_gpio *dev = devid; + unsigned status, bank, bit, pending; + int ret; + status = adp5588_gpio_read(dev->client, INT_STAT); + + if (status & GPI_INT) { + ret = adp5588_gpio_read_intstat(dev->client, dev->irq_stat); + if (ret < 0) + memset(dev->irq_stat, 0, ARRAY_SIZE(dev->irq_stat)); + + for (bank = 0; bank <= ADP_BANK(MAXGPIO); bank++, bit = 0) { + pending = dev->irq_stat[bank] & dev->irq_mask[bank]; + + while (pending) { + if (pending & (1 << bit)) { + handle_nested_irq(dev->irq_base + + (bank << 3) + bit); + pending &= ~(1 << bit); + + } + bit++; + } + } + } + + adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */ + + return IRQ_HANDLED; +} + +static int adp5588_irq_setup(struct adp5588_gpio *dev) +{ + struct i2c_client *client = dev->client; + struct adp5588_gpio_platform_data *pdata = client->dev.platform_data; + unsigned gpio; + int ret; + + adp5588_gpio_write(client, CFG, AUTO_INC); + adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */ + adp5588_gpio_read_intstat(client, dev->irq_stat); /* read to clear */ + + dev->irq_base = pdata->irq_base; + mutex_init(&dev->irq_lock); + + for (gpio = 0; gpio < dev->gpio_chip.ngpio; gpio++) { + int irq = gpio + dev->irq_base; + set_irq_chip_data(irq, dev); + set_irq_chip_and_handler(irq, &adp5588_irq_chip, + handle_level_irq); + set_irq_nested_thread(irq, 1); +#ifdef CONFIG_ARM + set_irq_flags(irq, IRQF_VALID); +#else + set_irq_noprobe(irq); +#endif + } + + ret = request_threaded_irq(client->irq, + NULL, + adp5588_irq_handler, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + dev_name(&client->dev), dev); + if (ret) { + dev_err(&client->dev, "failed to request irq %d\n", + client->irq); + goto out; + } + + dev->gpio_chip.to_irq = adp5588_gpio_to_irq; + adp5588_gpio_write(client, CFG, AUTO_INC | INT_CFG | GPI_INT); + + return 0; + +out: + dev->irq_base = 0; + return ret; +} +static void adp5588_irq_teardown(struct adp5588_gpio *dev) +{ + if (dev->irq_base) + free_irq(dev->client->irq, dev); +} + +#else +static int adp5588_irq_setup(struct adp5588_gpio *dev) +{ + struct i2c_client *client = dev->client; + dev_warn(&client->dev, "interrupt support not compiled in\n"); + + return 0; +} + +static void adp5588_irq_teardown(struct adp5588_gpio *dev) +{ +} +#endif /* CONFIG_GPIO_ADP5588_IRQ */ + static int __devinit adp5588_gpio_probe(struct i2c_client *client, const struct i2c_device_id *id) { @@ -166,7 +389,6 @@ static int __devinit adp5588_gpio_probe( mutex_init(&dev->lock); - ret = adp5588_gpio_read(dev->client, DEV_ID); if (ret < 0) goto err; @@ -179,18 +401,28 @@ static int __devinit adp5588_gpio_probe( ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0); ret |= adp5588_gpio_write(client, GPIO_PULL1 + i, (pdata->pullup_dis_mask >> (8 * i)) & 0xFF); - + ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0); if (ret) goto err; } + if (pdata->irq_base) { + if (WA_DELAYED_READOUT_REVID(revid)) { + dev_warn(&client->dev, "GPIO int not supported\n"); + } else { + ret = adp5588_irq_setup(dev); + if (ret) + goto err; + } + } + ret = gpiochip_add(&dev->gpio_chip); if (ret) - goto err; + goto err_irq; - dev_info(&client->dev, "gpios %d..%d on a %s Rev. %d\n", + dev_info(&client->dev, "gpios %d..%d (IRQ Base %d) on a %s Rev. %d\n", gc->base, gc->base + gc->ngpio - 1, - client->name, revid); + pdata->irq_base, client->name, revid); if (pdata->setup) { ret = pdata->setup(client, gc->base, gc->ngpio, pdata->context); @@ -199,8 +431,11 @@ static int __devinit adp5588_gpio_probe( } i2c_set_clientdata(client, dev); + return 0; +err_irq: + adp5588_irq_teardown(dev); err: kfree(dev); return ret; @@ -222,6 +457,9 @@ static int __devexit adp5588_gpio_remove } } + if (dev->irq_base) + free_irq(dev->client->irq, dev); + ret = gpiochip_remove(&dev->gpio_chip); if (ret) { dev_err(&client->dev, "gpiochip_remove failed %d\n", ret); diff -puN include/linux/i2c/adp5588.h~gpio-adp5588-gpio-support-interrupt-controller include/linux/i2c/adp5588.h --- a/include/linux/i2c/adp5588.h~gpio-adp5588-gpio-support-interrupt-controller +++ a/include/linux/i2c/adp5588.h @@ -128,6 +128,7 @@ struct adp5588_kpad_platform_data { struct adp5588_gpio_platform_data { unsigned gpio_start; /* GPIO Chip base # */ + unsigned irq_base; /* interrupt base # */ unsigned pullup_dis_mask; /* Pull-Up Disable Mask */ int (*setup)(struct i2c_client *client, int gpio, unsigned ngpio, _ Patches currently in -mm which might be from michael.hennerich@xxxxxxxxxx are drivers-misc-ad525x_dpot-fix-typo-in-spi-write16-and-write24-transfer-counts.patch linux-next.patch drivers-misc-ad525x_dpot-fix-part-name-typos-in-defines.patch drivers-misc-ad525x_dpot-new-features.patch misc-devices-do-not-enable-by-default.patch gpio-adp5588-gpio-support-interrupt-controller.patch gpio-adp5588-gpio-gpio_start-must-be-signed.patch -- To unsubscribe from this list: send the line "unsubscribe mm-commits" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html