The patch titled
backlight: spi driver for LMS283GF05 LCD
has been removed from the -mm tree. Its filename was
backlight-spi-driver-for-lms283gf05-lcd.patch
This patch was dropped because it was merged into mainline or a subsystem tree
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: backlight: spi driver for LMS283GF05 LCD
From: Marek Vasut <marek.vasut@xxxxxxxxx>
ADd support for the SPI part of LMS283GF05 LCD. The LCD uses SPI for
initialization and powerdown sequences. No further defails are specified
in the datasheet about the initialization/powerdown sequence, just the
magic numbers that have to be sent over SPI bus. This LCD can be found in
the Aeronix Zipit Z2 handheld.
Signed-off-by: Marek Vasut <marek.vasut@xxxxxxxxx>
Cc: Richard Purdie <rpurdie@xxxxxxxxx>
Cc: David Brownell <david-b@xxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/video/backlight/Kconfig | 7
drivers/video/backlight/Makefile | 1
drivers/video/backlight/lms283gf05.c | 242 +++++++++++++++++++++++++
include/linux/spi/lms283gf05.h | 28 ++
4 files changed, 278 insertions(+)
diff -puN drivers/video/backlight/Kconfig~backlight-spi-driver-for-lms283gf05-lcd drivers/video/backlight/Kconfig
--- a/drivers/video/backlight/Kconfig~backlight-spi-driver-for-lms283gf05-lcd
+++ a/drivers/video/backlight/Kconfig
@@ -31,6 +31,13 @@ config LCD_CORGI
Say y here to support the LCD panels usually found on SHARP
corgi (C7x0) and spitz (Cxx00) models.
+config LCD_LMS283GF05
+ tristate "Samsung LMS283GF05 LCD"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
+ help
+ SPI driver for Samsung LMS283GF05. This provides basic support
+ for powering the LCD up/down through a sysfs interface.
+
config LCD_LTV350QV
tristate "Samsung LTV350QV LCD Panel"
depends on LCD_CLASS_DEVICE && SPI_MASTER
diff -puN drivers/video/backlight/Makefile~backlight-spi-driver-for-lms283gf05-lcd drivers/video/backlight/Makefile
--- a/drivers/video/backlight/Makefile~backlight-spi-driver-for-lms283gf05-lcd
+++ a/drivers/video/backlight/Makefile
@@ -3,6 +3,7 @@
obj-$(CONFIG_LCD_CLASS_DEVICE) += lcd.o
obj-$(CONFIG_LCD_CORGI) += corgi_lcd.o
obj-$(CONFIG_LCD_HP700) += jornada720_lcd.o
+obj-$(CONFIG_LCD_LMS283GF05) += lms283gf05.o
obj-$(CONFIG_LCD_LTV350QV) += ltv350qv.o
obj-$(CONFIG_LCD_ILI9320) += ili9320.o
obj-$(CONFIG_LCD_PLATFORM) += platform_lcd.o
diff -puN /dev/null drivers/video/backlight/lms283gf05.c
--- /dev/null
+++ a/drivers/video/backlight/lms283gf05.c
@@ -0,0 +1,242 @@
+/*
+ * lms283gf05.c -- support for Samsung LMS283GF05 LCD
+ *
+ * Copyright (c) 2009 Marek Vasut <marek.vasut@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/lcd.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/lms283gf05.h>
+
+struct lms283gf05_state {
+ struct spi_device *spi;
+ struct lcd_device *ld;
+};
+
+struct lms283gf05_seq {
+ unsigned char reg;
+ unsigned short value;
+ unsigned char delay;
+};
+
+/* Magic sequences supplied by manufacturer, for details refer to datasheet */
+static struct lms283gf05_seq disp_initseq[] = {
+ /* REG, VALUE, DELAY */
+ { 0x07, 0x0000, 0 },
+ { 0x13, 0x0000, 10 },
+
+ { 0x11, 0x3004, 0 },
+ { 0x14, 0x200F, 0 },
+ { 0x10, 0x1a20, 0 },
+ { 0x13, 0x0040, 50 },
+
+ { 0x13, 0x0060, 0 },
+ { 0x13, 0x0070, 200 },
+
+ { 0x01, 0x0127, 0 },
+ { 0x02, 0x0700, 0 },
+ { 0x03, 0x1030, 0 },
+ { 0x08, 0x0208, 0 },
+ { 0x0B, 0x0620, 0 },
+ { 0x0C, 0x0110, 0 },
+ { 0x30, 0x0120, 0 },
+ { 0x31, 0x0127, 0 },
+ { 0x32, 0x0000, 0 },
+ { 0x33, 0x0503, 0 },
+ { 0x34, 0x0727, 0 },
+ { 0x35, 0x0124, 0 },
+ { 0x36, 0x0706, 0 },
+ { 0x37, 0x0701, 0 },
+ { 0x38, 0x0F00, 0 },
+ { 0x39, 0x0F00, 0 },
+ { 0x40, 0x0000, 0 },
+ { 0x41, 0x0000, 0 },
+ { 0x42, 0x013f, 0 },
+ { 0x43, 0x0000, 0 },
+ { 0x44, 0x013f, 0 },
+ { 0x45, 0x0000, 0 },
+ { 0x46, 0xef00, 0 },
+ { 0x47, 0x013f, 0 },
+ { 0x48, 0x0000, 0 },
+ { 0x07, 0x0015, 30 },
+
+ { 0x07, 0x0017, 0 },
+
+ { 0x20, 0x0000, 0 },
+ { 0x21, 0x0000, 0 },
+ { 0x22, 0x0000, 0 }
+};
+
+static struct lms283gf05_seq disp_pdwnseq[] = {
+ { 0x07, 0x0016, 30 },
+
+ { 0x07, 0x0004, 0 },
+ { 0x10, 0x0220, 20 },
+
+ { 0x13, 0x0060, 50 },
+
+ { 0x13, 0x0040, 50 },
+
+ { 0x13, 0x0000, 0 },
+ { 0x10, 0x0000, 0 }
+};
+
+
+static void lms283gf05_reset(unsigned long gpio, bool inverted)
+{
+ gpio_set_value(gpio, !inverted);
+ mdelay(100);
+ gpio_set_value(gpio, inverted);
+ mdelay(20);
+ gpio_set_value(gpio, !inverted);
+ mdelay(20);
+}
+
+static void lms283gf05_toggle(struct spi_device *spi,
+ struct lms283gf05_seq *seq, int sz)
+{
+ char buf[3];
+ int i;
+
+ for (i = 0; i < sz; i++) {
+ buf[0] = 0x74;
+ buf[1] = 0x00;
+ buf[2] = seq[i].reg;
+ spi_write(spi, buf, 3);
+
+ buf[0] = 0x76;
+ buf[1] = seq[i].value >> 8;
+ buf[2] = seq[i].value & 0xff;
+ spi_write(spi, buf, 3);
+
+ mdelay(seq[i].delay);
+ }
+}
+
+static int lms283gf05_power_set(struct lcd_device *ld, int power)
+{
+ struct lms283gf05_state *st = lcd_get_data(ld);
+ struct spi_device *spi = st->spi;
+ struct lms283gf05_pdata *pdata = spi->dev.platform_data;
+
+ if (power) {
+ if (pdata)
+ lms283gf05_reset(pdata->reset_gpio,
+ pdata->reset_inverted);
+ lms283gf05_toggle(spi, disp_initseq, ARRAY_SIZE(disp_initseq));
+ } else {
+ lms283gf05_toggle(spi, disp_pdwnseq, ARRAY_SIZE(disp_pdwnseq));
+ if (pdata)
+ gpio_set_value(pdata->reset_gpio,
+ pdata->reset_inverted);
+ }
+
+ return 0;
+}
+
+static struct lcd_ops lms_ops = {
+ .set_power = lms283gf05_power_set,
+ .get_power = NULL,
+};
+
+static int __devinit lms283gf05_probe(struct spi_device *spi)
+{
+ struct lms283gf05_state *st;
+ struct lms283gf05_pdata *pdata = spi->dev.platform_data;
+ struct lcd_device *ld;
+ int ret = 0;
+
+ if (pdata != NULL) {
+ ret = gpio_request(pdata->reset_gpio, "LMS285GF05 RESET");
+ if (ret)
+ return ret;
+
+ ret = gpio_direction_output(pdata->reset_gpio,
+ !pdata->reset_inverted);
+ if (ret)
+ goto err;
+ }
+
+ st = kzalloc(sizeof(struct lms283gf05_state), GFP_KERNEL);
+ if (st == NULL) {
+ dev_err(&spi->dev, "No memory for device state\n");
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ ld = lcd_device_register("lms283gf05", &spi->dev, st, &lms_ops);
+ if (IS_ERR(ld)) {
+ ret = PTR_ERR(ld);
+ goto err2;
+ }
+
+ st->spi = spi;
+ st->ld = ld;
+
+ dev_set_drvdata(&spi->dev, st);
+
+ /* kick in the LCD */
+ if (pdata)
+ lms283gf05_reset(pdata->reset_gpio, pdata->reset_inverted);
+ lms283gf05_toggle(spi, disp_initseq, ARRAY_SIZE(disp_initseq));
+
+ return 0;
+
+err2:
+ kfree(st);
+err:
+ if (pdata != NULL)
+ gpio_free(pdata->reset_gpio);
+
+ return ret;
+}
+
+static int __devexit lms283gf05_remove(struct spi_device *spi)
+{
+ struct lms283gf05_state *st = dev_get_drvdata(&spi->dev);
+ struct lms283gf05_pdata *pdata = st->spi->dev.platform_data;
+
+ lcd_device_unregister(st->ld);
+
+ if (pdata != NULL)
+ gpio_free(pdata->reset_gpio);
+
+ kfree(st);
+
+ return 0;
+}
+
+static struct spi_driver lms283gf05_driver = {
+ .driver = {
+ .name = "lms283gf05",
+ .owner = THIS_MODULE,
+ },
+ .probe = lms283gf05_probe,
+ .remove = __devexit_p(lms283gf05_remove),
+};
+
+static __init int lms283gf05_init(void)
+{
+ return spi_register_driver(&lms283gf05_driver);
+}
+
+static __exit void lms283gf05_exit(void)
+{
+ spi_unregister_driver(&lms283gf05_driver);
+}
+
+module_init(lms283gf05_init);
+module_exit(lms283gf05_exit);
+
+MODULE_AUTHOR("Marek Vasut <marek.vasut@xxxxxxxxx>");
+MODULE_DESCRIPTION("LCD283GF05 LCD");
+MODULE_LICENSE("GPL v2");
diff -puN /dev/null include/linux/spi/lms283gf05.h
--- /dev/null
+++ a/include/linux/spi/lms283gf05.h
@@ -0,0 +1,28 @@
+/*
+ * lms283gf05.h - Platform glue for Samsung LMS283GF05 LCD
+ *
+ * Copyright (C) 2009 Marek Vasut <marek.vasut@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+*/
+
+#ifndef _INCLUDE_LINUX_SPI_LMS283GF05_H_
+#define _INCLUDE_LINUX_SPI_LMS283GF05_H_
+
+struct lms283gf05_pdata {
+ unsigned long reset_gpio;
+ bool reset_inverted;
+};
+
+#endif /* _INCLUDE_LINUX_SPI_LMS283GF05_H_ */
_
Patches currently in -mm which might be from marek.vasut@xxxxxxxxx are
linux-next.patch
mfd-gpio-add-a-gpio-interface-to-the-ucb1400-mfd-chip-driver-via-gpiolib.patch
--
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
