The patch titled
fbdev: remove outdated advice about I2C configuration
has been removed from the -mm tree. Its filename was
fbdev-remove-outdated-advice-about-i2c-configuration.patch
This patch was dropped because it was merged into mainline or a subsystem tree
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: fbdev: remove outdated advice about I2C configuration
From: Jean Delvare <khali@xxxxxxxxxxxx>
The required I2C modules are now selected automatically by the means
of select statements in Kconfig, so there is no point in confusing the
users with options he/she would be supposed to enable manually.
Signed-off-by: Jean Delvare <khali@xxxxxxxxxxxx>
Cc: Krzysztof Helt <krzysztof.h1@xxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/video/Kconfig | 23 ++++-------------------
1 file changed, 4 insertions(+), 19 deletions(-)
diff -puN drivers/video/Kconfig~fbdev-remove-outdated-advice-about-i2c-configuration drivers/video/Kconfig
--- a/drivers/video/Kconfig~fbdev-remove-outdated-advice-about-i2c-configuration
+++ a/drivers/video/Kconfig
@@ -1128,13 +1128,6 @@ config FB_INTEL
830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
Say Y if you have and plan to use such a board.
- If you say Y here and want DDC/I2C support you must first say Y to
- "I2C support" and "I2C bit-banging support" in the character devices
- section.
-
- If you say M here then "I2C support" and "I2C bit-banging support"
- can be build either as modules or built-in.
-
To compile this driver as a module, choose M here: the
module will be called intelfb.
@@ -1207,11 +1200,10 @@ config FB_MATROX_G
pixel and 32 bpp packed pixel. You can also use font widths
different from 8.
- If you need support for G400 secondary head, you must first say Y to
- "I2C support" in the character devices section, and then to
- "Matrox I2C support" and "G400 second head support" here in the
- framebuffer section. G450/G550 secondary head and digital output
- are supported without additional modules.
+ If you need support for G400 secondary head, you must say Y to
+ "Matrox I2C support" and "G400 second head support" right below.
+ G450/G550 secondary head and digital output are supported without
+ additional modules.
The driver starts in monitor mode. You must use the matroxset tool
(available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
@@ -1310,13 +1302,6 @@ config FB_RADEON
a framebuffer device. There are both PCI and AGP versions. You
don't need to choose this to run the Radeon in plain VGA mode.
- If you say Y here and want DDC/I2C support you must first say Y to
- "I2C support" and "I2C bit-banging support" in the character devices
- section.
-
- If you say M here then "I2C support" and "I2C bit-banging support"
- can be build either as modules or built-in.
-
There is a product page at
http://apps.ati.com/ATIcompare/
_
Patches currently in -mm which might be from khali@xxxxxxxxxxxx are
origin.patch
linux-next.patch
dell-laptop-fix-uninitialized-wrong-return-value.patch
rtc-add-stand-alone-driver-for-rx8025-chip.patch
rtc-add-stand-alone-driver-for-rx8025-chip-fix.patch
pca953x-support-gpiolib-gpio-naming.patch
--
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
