The patch titled
hdq driver for OMAP2430/3430
has been added to the -mm tree. Its filename is
hdq-driver-for-omap2430-3430.patch
Before you just go and hit "reply", please:
a) Consider who else should be cc'ed
b) Prefer to cc a suitable mailing list as well
c) Ideally: find the original patch on the mailing list and do a
reply-to-all to that, adding suitable additional cc's
*** Remember to use Documentation/SubmitChecklist when testing your code ***
See http://userweb.kernel.org/~akpm/added-to-mm.txt to find
out what to do about this
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: hdq driver for OMAP2430/3430
From: Madhusudhan Chikkature <madhu.cr@xxxxxx>
The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols. These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).
This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@xxxxxx>
Acked-by: Felipe Balbi <felipe.balbi@xxxxxxxxx>
Acked-by: Evgeniy Polyakov <johnpol@xxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/w1/masters/Kconfig | 7
drivers/w1/masters/Makefile | 1
drivers/w1/masters/omap_hdq.c | 725 ++++++++++++++++++++++++++++++++
3 files changed, 733 insertions(+)
diff -puN drivers/w1/masters/Kconfig~hdq-driver-for-omap2430-3430 drivers/w1/masters/Kconfig
--- a/drivers/w1/masters/Kconfig~hdq-driver-for-omap2430-3430
+++ a/drivers/w1/masters/Kconfig
@@ -52,5 +52,12 @@ config W1_MASTER_GPIO
This support is also available as a module. If so, the module
will be called w1-gpio.ko.
+config HDQ_MASTER_OMAP
+ tristate "OMAP HDQ driver"
+ depends on ARCH_OMAP2430 || ARCH_OMAP34XX
+ help
+ Say Y here if you want support for the 1-wire or HDQ Interface
+ on an OMAP processor.
+
endmenu
diff -puN drivers/w1/masters/Makefile~hdq-driver-for-omap2430-3430 drivers/w1/masters/Makefile
--- a/drivers/w1/masters/Makefile~hdq-driver-for-omap2430-3430
+++ a/drivers/w1/masters/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_W1_MASTER_DS2490) += ds249
obj-$(CONFIG_W1_MASTER_DS2482) += ds2482.o
obj-$(CONFIG_W1_MASTER_DS1WM) += ds1wm.o
obj-$(CONFIG_W1_MASTER_GPIO) += w1-gpio.o
+obj-$(CONFIG_HDQ_MASTER_OMAP) += omap_hdq.o
diff -puN /dev/null drivers/w1/masters/omap_hdq.c
--- /dev/null
+++ a/drivers/w1/masters/omap_hdq.c
@@ -0,0 +1,725 @@
+/*
+ * drivers/w1/masters/omap_hdq.c
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <asm/irq.h>
+#include <mach/hardware.h>
+
+#include "../w1.h"
+#include "../w1_int.h"
+
+#define MOD_NAME "OMAP_HDQ:"
+
+#define OMAP_HDQ_REVISION 0x00
+#define OMAP_HDQ_TX_DATA 0x04
+#define OMAP_HDQ_RX_DATA 0x08
+#define OMAP_HDQ_CTRL_STATUS 0x0c
+#define OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK (1<<6)
+#define OMAP_HDQ_CTRL_STATUS_CLOCKENABLE (1<<5)
+#define OMAP_HDQ_CTRL_STATUS_GO (1<<4)
+#define OMAP_HDQ_CTRL_STATUS_INITIALIZATION (1<<2)
+#define OMAP_HDQ_CTRL_STATUS_DIR (1<<1)
+#define OMAP_HDQ_CTRL_STATUS_MODE (1<<0)
+#define OMAP_HDQ_INT_STATUS 0x10
+#define OMAP_HDQ_INT_STATUS_TXCOMPLETE (1<<2)
+#define OMAP_HDQ_INT_STATUS_RXCOMPLETE (1<<1)
+#define OMAP_HDQ_INT_STATUS_TIMEOUT (1<<0)
+#define OMAP_HDQ_SYSCONFIG 0x14
+#define OMAP_HDQ_SYSCONFIG_SOFTRESET (1<<1)
+#define OMAP_HDQ_SYSCONFIG_AUTOIDLE (1<<0)
+#define OMAP_HDQ_SYSSTATUS 0x18
+#define OMAP_HDQ_SYSSTATUS_RESETDONE (1<<0)
+
+#define OMAP_HDQ_FLAG_CLEAR 0
+#define OMAP_HDQ_FLAG_SET 1
+#define OMAP_HDQ_TIMEOUT (HZ/5)
+
+#define OMAP_HDQ_MAX_USER 4
+
+static DECLARE_WAIT_QUEUE_HEAD(hdq_wait_queue);
+static int w1_id;
+
+struct hdq_data {
+ struct device *dev;
+ void __iomem *hdq_base;
+ /* lock status update */
+ struct mutex hdq_mutex;
+ int hdq_usecount;
+ struct clk *hdq_ick;
+ struct clk *hdq_fck;
+ u8 hdq_irqstatus;
+ /* device lock */
+ spinlock_t hdq_spinlock;
+ /*
+ * Used to control the call to omap_hdq_get and omap_hdq_put.
+ * HDQ Protocol: Write the CMD|REG_address first, followed by
+ * the data wrire or read.
+ */
+ int init_trans;
+};
+
+static int __init omap_hdq_probe(struct platform_device *pdev);
+static int omap_hdq_remove(struct platform_device *pdev);
+
+static struct platform_driver omap_hdq_driver = {
+ .probe = omap_hdq_probe,
+ .remove = omap_hdq_remove,
+ .driver = {
+ .name = "omap_hdq",
+ },
+};
+
+static u8 omap_w1_read_byte(void *_hdq);
+static void omap_w1_write_byte(void *_hdq, u8 byte);
+static u8 omap_w1_reset_bus(void *_hdq);
+static void omap_w1_search_bus(void *_hdq, u8 search_type,
+ w1_slave_found_callback slave_found);
+
+
+static struct w1_bus_master omap_w1_master = {
+ .read_byte = omap_w1_read_byte,
+ .write_byte = omap_w1_write_byte,
+ .reset_bus = omap_w1_reset_bus,
+ .search = omap_w1_search_bus,
+};
+
+/* HDQ register I/O routines */
+static inline u8 hdq_reg_in(struct hdq_data *hdq_data, u32 offset)
+{
+ return __raw_readb(hdq_data->hdq_base + offset);
+}
+
+static inline void hdq_reg_out(struct hdq_data *hdq_data, u32 offset, u8 val)
+{
+ __raw_writeb(val, hdq_data->hdq_base + offset);
+}
+
+static inline u8 hdq_reg_merge(struct hdq_data *hdq_data, u32 offset,
+ u8 val, u8 mask)
+{
+ u8 new_val = (__raw_readb(hdq_data->hdq_base + offset) & ~mask)
+ | (val & mask);
+ __raw_writeb(new_val, hdq_data->hdq_base + offset);
+
+ return new_val;
+}
+
+/*
+ * Wait for one or more bits in flag change.
+ * HDQ_FLAG_SET: wait until any bit in the flag is set.
+ * HDQ_FLAG_CLEAR: wait until all bits in the flag are cleared.
+ * return 0 on success and -ETIMEDOUT in the case of timeout.
+ */
+static int hdq_wait_for_flag(struct hdq_data *hdq_data, u32 offset,
+ u8 flag, u8 flag_set, u8 *status)
+{
+ int ret = 0;
+ unsigned long timeout = jiffies + OMAP_HDQ_TIMEOUT;
+
+ if (flag_set == OMAP_HDQ_FLAG_CLEAR) {
+ /* wait for the flag clear */
+ while (((*status = hdq_reg_in(hdq_data, offset)) & flag)
+ && time_before(jiffies, timeout)) {
+ schedule_timeout_uninterruptible(1);
+ }
+ if (*status & flag)
+ ret = -ETIMEDOUT;
+ } else if (flag_set == OMAP_HDQ_FLAG_SET) {
+ /* wait for the flag set */
+ while (!((*status = hdq_reg_in(hdq_data, offset)) & flag)
+ && time_before(jiffies, timeout)) {
+ schedule_timeout_uninterruptible(1);
+ }
+ if (!(*status & flag))
+ ret = -ETIMEDOUT;
+ } else
+ return -EINVAL;
+
+ return ret;
+}
+
+/* write out a byte and fill *status with HDQ_INT_STATUS */
+static int hdq_write_byte(struct hdq_data *hdq_data, u8 val, u8 *status)
+{
+ int ret;
+ u8 tmp_status;
+ unsigned long irqflags;
+
+ *status = 0;
+
+ spin_lock_irqsave(&hdq_data->hdq_spinlock, irqflags);
+ /* clear interrupt flags via a dummy read */
+ hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
+ /* ISR loads it with new INT_STATUS */
+ hdq_data->hdq_irqstatus = 0;
+ spin_unlock_irqrestore(&hdq_data->hdq_spinlock, irqflags);
+
+ hdq_reg_out(hdq_data, OMAP_HDQ_TX_DATA, val);
+
+ /* set the GO bit */
+ hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS, OMAP_HDQ_CTRL_STATUS_GO,
+ OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_GO);
+ /* wait for the TXCOMPLETE bit */
+ ret = wait_event_timeout(hdq_wait_queue,
+ hdq_data->hdq_irqstatus, OMAP_HDQ_TIMEOUT);
+ if (ret == 0) {
+ dev_dbg(hdq_data->dev, "TX wait elapsed\n");
+ goto out;
+ }
+
+ *status = hdq_data->hdq_irqstatus;
+ /* check irqstatus */
+ if (!(*status & OMAP_HDQ_INT_STATUS_TXCOMPLETE)) {
+ dev_dbg(hdq_data->dev, "timeout waiting for"
+ "TXCOMPLETE/RXCOMPLETE, %x", *status);
+ ret = -ETIMEDOUT;
+ goto out;
+ }
+
+ /* wait for the GO bit return to zero */
+ ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_CTRL_STATUS,
+ OMAP_HDQ_CTRL_STATUS_GO,
+ OMAP_HDQ_FLAG_CLEAR, &tmp_status);
+ if (ret) {
+ dev_dbg(hdq_data->dev, "timeout waiting GO bit"
+ "return to zero, %x", tmp_status);
+ }
+
+out:
+ return ret;
+}
+
+/* HDQ Interrupt service routine */
+static irqreturn_t hdq_isr(int irq, void *_hdq)
+{
+ struct hdq_data *hdq_data = _hdq;
+ unsigned long irqflags;
+
+ spin_lock_irqsave(&hdq_data->hdq_spinlock, irqflags);
+ hdq_data->hdq_irqstatus = hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
+ spin_unlock_irqrestore(&hdq_data->hdq_spinlock, irqflags);
+ dev_dbg(hdq_data->dev, "hdq_isr: %x", hdq_data->hdq_irqstatus);
+
+ if (hdq_data->hdq_irqstatus &
+ (OMAP_HDQ_INT_STATUS_TXCOMPLETE | OMAP_HDQ_INT_STATUS_RXCOMPLETE
+ | OMAP_HDQ_INT_STATUS_TIMEOUT)) {
+ /* wake up sleeping process */
+ wake_up(&hdq_wait_queue);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/* HDQ Mode: always return success */
+static u8 omap_w1_reset_bus(void *_hdq)
+{
+ return 0;
+}
+
+/* W1 search callback function */
+static void omap_w1_search_bus(void *_hdq, u8 search_type,
+ w1_slave_found_callback slave_found)
+{
+ u64 module_id, rn_le, cs, id;
+
+ if (w1_id)
+ module_id = w1_id;
+ else
+ module_id = 0x1;
+
+ rn_le = cpu_to_le64(module_id);
+ /*
+ * HDQ might not obey truly the 1-wire spec.
+ * So calculate CRC based on module parameter.
+ */
+ cs = w1_calc_crc8((u8 *)&rn_le, 7);
+ id = (cs << 56) | module_id;
+
+ slave_found(_hdq, id);
+}
+
+static int _omap_hdq_reset(struct hdq_data *hdq_data)
+{
+ int ret;
+ u8 tmp_status;
+
+ hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG, OMAP_HDQ_SYSCONFIG_SOFTRESET);
+ /*
+ * Select HDQ mode & enable clocks.
+ * It is observed that INT flags can't be cleared via a read and GO/INIT
+ * won't return to zero if interrupt is disabled. So we always enable
+ * interrupt.
+ */
+ hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
+ OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
+ OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
+
+ /* wait for reset to complete */
+ ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_SYSSTATUS,
+ OMAP_HDQ_SYSSTATUS_RESETDONE, OMAP_HDQ_FLAG_SET, &tmp_status);
+ if (ret)
+ dev_dbg(hdq_data->dev, "timeout waiting HDQ reset, %x",
+ tmp_status);
+ else {
+ hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
+ OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
+ OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
+ hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
+ OMAP_HDQ_SYSCONFIG_AUTOIDLE);
+ }
+
+ return ret;
+}
+
+/* Issue break pulse to the device */
+static int omap_hdq_break(struct hdq_data *hdq_data)
+{
+ int ret = 0;
+ u8 tmp_status;
+ unsigned long irqflags;
+
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0) {
+ dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
+ ret = -EINTR;
+ goto rtn;
+ }
+
+ spin_lock_irqsave(&hdq_data->hdq_spinlock, irqflags);
+ /* clear interrupt flags via a dummy read */
+ hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
+ /* ISR loads it with new INT_STATUS */
+ hdq_data->hdq_irqstatus = 0;
+ spin_unlock_irqrestore(&hdq_data->hdq_spinlock, irqflags);
+
+ /* set the INIT and GO bit */
+ hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS,
+ OMAP_HDQ_CTRL_STATUS_INITIALIZATION | OMAP_HDQ_CTRL_STATUS_GO,
+ OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_INITIALIZATION |
+ OMAP_HDQ_CTRL_STATUS_GO);
+
+ /* wait for the TIMEOUT bit */
+ ret = wait_event_timeout(hdq_wait_queue,
+ hdq_data->hdq_irqstatus, OMAP_HDQ_TIMEOUT);
+ if (ret == 0) {
+ dev_dbg(hdq_data->dev, "break wait elapsed\n");
+ ret = -EINTR;
+ goto out;
+ }
+
+ tmp_status = hdq_data->hdq_irqstatus;
+ /* check irqstatus */
+ if (!(tmp_status & OMAP_HDQ_INT_STATUS_TIMEOUT)) {
+ dev_dbg(hdq_data->dev, "timeout waiting for TIMEOUT, %x",
+ tmp_status);
+ ret = -ETIMEDOUT;
+ goto out;
+ }
+ /*
+ * wait for both INIT and GO bits rerurn to zero.
+ * zero wait time expected for interrupt mode.
+ */
+ ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_CTRL_STATUS,
+ OMAP_HDQ_CTRL_STATUS_INITIALIZATION |
+ OMAP_HDQ_CTRL_STATUS_GO, OMAP_HDQ_FLAG_CLEAR,
+ &tmp_status);
+ if (ret)
+ dev_dbg(hdq_data->dev, "timeout waiting INIT&GO bits"
+ "return to zero, %x", tmp_status);
+
+out:
+ mutex_unlock(&hdq_data->hdq_mutex);
+rtn:
+ return ret;
+}
+
+static int hdq_read_byte(struct hdq_data *hdq_data, u8 *val)
+{
+ int ret = 0;
+ u8 status;
+ unsigned long timeout = jiffies + OMAP_HDQ_TIMEOUT;
+
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0) {
+ ret = -EINTR;
+ goto rtn;
+ }
+
+ if (!hdq_data->hdq_usecount) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (!(hdq_data->hdq_irqstatus & OMAP_HDQ_INT_STATUS_RXCOMPLETE)) {
+ hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS,
+ OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_GO,
+ OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_GO);
+ /*
+ * The RX comes immediately after TX. It
+ * triggers another interrupt before we
+ * sleep. So we have to wait for RXCOMPLETE bit.
+ */
+ while (!(hdq_data->hdq_irqstatus
+ & OMAP_HDQ_INT_STATUS_RXCOMPLETE)
+ && time_before(jiffies, timeout)) {
+ schedule_timeout_uninterruptible(1);
+ }
+ hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS, 0,
+ OMAP_HDQ_CTRL_STATUS_DIR);
+ status = hdq_data->hdq_irqstatus;
+ /* check irqstatus */
+ if (!(status & OMAP_HDQ_INT_STATUS_RXCOMPLETE)) {
+ dev_dbg(hdq_data->dev, "timeout waiting for"
+ "RXCOMPLETE, %x", status);
+ ret = -ETIMEDOUT;
+ goto out;
+ }
+ }
+ /* the data is ready. Read it in! */
+ *val = hdq_reg_in(hdq_data, OMAP_HDQ_RX_DATA);
+out:
+ mutex_unlock(&hdq_data->hdq_mutex);
+rtn:
+ return 0;
+
+}
+
+/* Enable clocks and set the controller to HDQ mode */
+static int omap_hdq_get(struct hdq_data *hdq_data)
+{
+ int ret = 0;
+
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0) {
+ ret = -EINTR;
+ goto rtn;
+ }
+
+ if (OMAP_HDQ_MAX_USER == hdq_data->hdq_usecount) {
+ dev_dbg(hdq_data->dev, "attempt to exceed the max use count");
+ ret = -EINVAL;
+ goto out;
+ } else {
+ hdq_data->hdq_usecount++;
+ try_module_get(THIS_MODULE);
+ if (1 == hdq_data->hdq_usecount) {
+ if (clk_enable(hdq_data->hdq_ick)) {
+ dev_dbg(hdq_data->dev, "Can not enable ick\n");
+ ret = -ENODEV;
+ goto clk_err;
+ }
+ if (clk_enable(hdq_data->hdq_fck)) {
+ dev_dbg(hdq_data->dev, "Can not enable fck\n");
+ clk_disable(hdq_data->hdq_ick);
+ ret = -ENODEV;
+ goto clk_err;
+ }
+
+ /* make sure HDQ is out of reset */
+ if (!(hdq_reg_in(hdq_data, OMAP_HDQ_SYSSTATUS) &
+ OMAP_HDQ_SYSSTATUS_RESETDONE)) {
+ ret = _omap_hdq_reset(hdq_data);
+ if (ret)
+ /* back up the count */
+ hdq_data->hdq_usecount--;
+ } else {
+ /* select HDQ mode & enable clocks */
+ hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
+ OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
+ OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
+ hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
+ OMAP_HDQ_SYSCONFIG_AUTOIDLE);
+ hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
+ }
+ }
+ }
+
+clk_err:
+ clk_put(hdq_data->hdq_ick);
+ clk_put(hdq_data->hdq_fck);
+out:
+ mutex_unlock(&hdq_data->hdq_mutex);
+rtn:
+ return ret;
+}
+
+/* Disable clocks to the module */
+static int omap_hdq_put(struct hdq_data *hdq_data)
+{
+ int ret = 0;
+
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0)
+ return -EINTR;
+
+ if (0 == hdq_data->hdq_usecount) {
+ dev_dbg(hdq_data->dev, "attempt to decrement use count"
+ "when it is zero");
+ ret = -EINVAL;
+ } else {
+ hdq_data->hdq_usecount--;
+ module_put(THIS_MODULE);
+ if (0 == hdq_data->hdq_usecount) {
+ clk_disable(hdq_data->hdq_ick);
+ clk_disable(hdq_data->hdq_fck);
+ }
+ }
+ mutex_unlock(&hdq_data->hdq_mutex);
+
+ return ret;
+}
+
+/* Read a byte of data from the device */
+static u8 omap_w1_read_byte(void *_hdq)
+{
+ struct hdq_data *hdq_data = _hdq;
+ u8 val = 0;
+ int ret;
+
+ ret = hdq_read_byte(hdq_data, &val);
+ if (ret) {
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0) {
+ dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
+ return -EINTR;
+ }
+ hdq_data->init_trans = 0;
+ mutex_unlock(&hdq_data->hdq_mutex);
+ omap_hdq_put(hdq_data);
+ return -1;
+ }
+
+ /* Write followed by a read, release the module */
+ if (hdq_data->init_trans) {
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0) {
+ dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
+ return -EINTR;
+ }
+ hdq_data->init_trans = 0;
+ mutex_unlock(&hdq_data->hdq_mutex);
+ omap_hdq_put(hdq_data);
+ }
+
+ return val;
+}
+
+/* Write a byte of data to the device */
+static void omap_w1_write_byte(void *_hdq, u8 byte)
+{
+ struct hdq_data *hdq_data = _hdq;
+ int ret;
+ u8 status;
+
+ /* First write to initialize the transfer */
+ if (hdq_data->init_trans == 0)
+ omap_hdq_get(hdq_data);
+
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0) {
+ dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
+ return;
+ }
+ hdq_data->init_trans++;
+ mutex_unlock(&hdq_data->hdq_mutex);
+
+ ret = hdq_write_byte(hdq_data, byte, &status);
+ if (ret == 0) {
+ dev_dbg(hdq_data->dev, "TX failure:Ctrl status %x\n", status);
+ return;
+ }
+
+ /* Second write, data transfered. Release the module */
+ if (hdq_data->init_trans > 1) {
+ omap_hdq_put(hdq_data);
+ ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
+ if (ret < 0) {
+ dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
+ return;
+ }
+ hdq_data->init_trans = 0;
+ mutex_unlock(&hdq_data->hdq_mutex);
+ }
+
+ return;
+}
+
+static int __init omap_hdq_probe(struct platform_device *pdev)
+{
+ struct hdq_data *hdq_data;
+ struct resource *res;
+ int ret, irq;
+ u8 rev;
+
+ hdq_data = kmalloc(sizeof(*hdq_data), GFP_KERNEL);
+ if (!hdq_data) {
+ dev_dbg(&pdev->dev, "unable to allocate memory\n");
+ ret = -ENOMEM;
+ goto err_kmalloc;
+ }
+
+ hdq_data->dev = &pdev->dev;
+ platform_set_drvdata(pdev, hdq_data);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_dbg(&pdev->dev, "unable to get resource\n");
+ ret = -ENXIO;
+ goto err_resource;
+ }
+
+ hdq_data->hdq_base = ioremap(res->start, SZ_4K);
+ if (!hdq_data->hdq_base) {
+ dev_dbg(&pdev->dev, "ioremap failed\n");
+ ret = -EINVAL;
+ goto err_ioremap;
+ }
+
+ /* get interface & functional clock objects */
+ hdq_data->hdq_ick = clk_get(&pdev->dev, "hdq_ick");
+ hdq_data->hdq_fck = clk_get(&pdev->dev, "hdq_fck");
+
+ if (IS_ERR(hdq_data->hdq_ick) || IS_ERR(hdq_data->hdq_fck)) {
+ dev_dbg(&pdev->dev, "Can't get HDQ clock objects\n");
+ if (IS_ERR(hdq_data->hdq_ick)) {
+ ret = PTR_ERR(hdq_data->hdq_ick);
+ goto err_clk;
+ }
+ if (IS_ERR(hdq_data->hdq_fck)) {
+ ret = PTR_ERR(hdq_data->hdq_fck);
+ clk_put(hdq_data->hdq_ick);
+ goto err_clk;
+ }
+ }
+
+ hdq_data->hdq_usecount = 0;
+ mutex_init(&hdq_data->hdq_mutex);
+
+ if (clk_enable(hdq_data->hdq_ick)) {
+ dev_dbg(&pdev->dev, "Can not enable ick\n");
+ ret = -ENODEV;
+ goto err_intfclk;
+ }
+
+ if (clk_enable(hdq_data->hdq_fck)) {
+ dev_dbg(&pdev->dev, "Can not enable fck\n");
+ ret = -ENODEV;
+ goto err_fnclk;
+ }
+
+ rev = hdq_reg_in(hdq_data, OMAP_HDQ_REVISION);
+ dev_info(&pdev->dev, "OMAP HDQ Hardware Rev %c.%c. Driver in %s mode\n",
+ (rev >> 4) + '0', (rev & 0x0f) + '0', "Interrupt");
+
+ spin_lock_init(&hdq_data->hdq_spinlock);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ ret = -ENXIO;
+ goto err_irq;
+ }
+
+ ret = request_irq(irq, hdq_isr, IRQF_DISABLED, "omap_hdq", hdq_data);
+ if (ret < 0) {
+ dev_dbg(&pdev->dev, "could not request irq\n");
+ goto err_irq;
+ }
+
+ omap_hdq_break(hdq_data);
+
+ /* don't clock the HDQ until it is needed */
+ clk_disable(hdq_data->hdq_ick);
+ clk_disable(hdq_data->hdq_fck);
+
+ omap_w1_master.data = hdq_data;
+
+ ret = w1_add_master_device(&omap_w1_master);
+ if (ret) {
+ dev_dbg(&pdev->dev, "Failure in registering w1 master\n");
+ goto err_w1;
+ }
+
+ return 0;
+
+err_w1:
+err_irq:
+ clk_disable(hdq_data->hdq_fck);
+
+err_fnclk:
+ clk_disable(hdq_data->hdq_ick);
+
+err_intfclk:
+ clk_put(hdq_data->hdq_ick);
+ clk_put(hdq_data->hdq_fck);
+
+err_clk:
+ iounmap(hdq_data->hdq_base);
+
+err_ioremap:
+err_resource:
+ platform_set_drvdata(pdev, NULL);
+ kfree(hdq_data);
+
+err_kmalloc:
+ return ret;
+
+}
+
+static int omap_hdq_remove(struct platform_device *pdev)
+{
+ struct hdq_data *hdq_data = platform_get_drvdata(pdev);
+
+ mutex_lock(&hdq_data->hdq_mutex);
+
+ if (hdq_data->hdq_usecount) {
+ dev_dbg(&pdev->dev, "removed when use count is not zero\n");
+ return -EBUSY;
+ }
+
+ mutex_unlock(&hdq_data->hdq_mutex);
+
+ /* remove module dependency */
+ clk_put(hdq_data->hdq_ick);
+ clk_put(hdq_data->hdq_fck);
+ free_irq(INT_24XX_HDQ_IRQ, hdq_data);
+ platform_set_drvdata(pdev, NULL);
+ iounmap(hdq_data->hdq_base);
+ kfree(hdq_data);
+
+ return 0;
+}
+
+static int __init
+omap_hdq_init(void)
+{
+ return platform_driver_register(&omap_hdq_driver);
+}
+module_init(omap_hdq_init);
+
+static void __exit
+omap_hdq_exit(void)
+{
+ platform_driver_unregister(&omap_hdq_driver);
+}
+module_exit(omap_hdq_exit);
+
+module_param(w1_id, int, S_IRUSR);
+MODULE_PARM_DESC(w1_id, "1-wire id for the slave detection");
+
+MODULE_AUTHOR("Texas Instruments");
+MODULE_DESCRIPTION("HDQ driver Library");
+MODULE_LICENSE("GPL");
_
Patches currently in -mm which might be from madhu.cr@xxxxxx are
w1-export-w1_read_8-function.patch
w1-export-w1_read_8-function-checkpatch-fixes.patch
hdq-driver-for-omap2430-3430.patch
hdq-bq27000-hdq-slave-interface-driver.patch
hdq-documentation-for-omap-hdq.patch
--
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
