The patch titled
hwmon: new chip driver for TI ADS7828 A-D
has been added to the -mm tree. Its filename is
hwmon-new-chip-driver-for-ti-ads7828-a-d.patch
*** Remember to use Documentation/SubmitChecklist when testing your code ***
See http://www.zip.com.au/~akpm/linux/patches/stuff/added-to-mm.txt to find
out what to do about this
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: hwmon: new chip driver for TI ADS7828 A-D
From: Steve Hardy <steve@xxxxxxxxxxxxxxxxxxx>
Signed-off-by: Steve Hardy <steve@xxxxxxxxxxxxxxxxxxx>
Cc: Mark M. Hoffman <mhoffman@xxxxxxxxxxxxx>
Cc: Jean Delvare <khali@xxxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
Documentation/hwmon/ads7828 | 38 ++++
drivers/hwmon/Kconfig | 10 +
drivers/hwmon/Makefile | 1
drivers/hwmon/ads7828.c | 296 ++++++++++++++++++++++++++++++++++
4 files changed, 345 insertions(+)
diff -puN /dev/null Documentation/hwmon/ads7828
--- /dev/null
+++ a/Documentation/hwmon/ads7828
@@ -0,0 +1,38 @@
+Kernel driver ads7828
+=====================
+
+Supported chips:
+ * Texas Instruments/Burr-Brown ADS7828
+ Prefix: 'ads7828'
+ Addresses scanned: I2C 0x48, 0x49, 0x4a, 0x4b
+ Datasheet: Publicly available at the Texas Instruments website :
+ http://focus.ti.com/lit/ds/symlink/ads7828.pdf
+
+Authors:
+ Steve Hardy <steve@xxxxxxxxxxxxxxxxxxx>
+
+Module Parameters
+-----------------
+
+* se_input: bool (default Y)
+ Single ended operation - set to N for differential mode
+* int_vref: bool (default Y)
+ Operate with the internal 2.5v reference - set to N for external reference
+* vref_mv: int (default 2500)
+ If using an external reference, set this to the reference voltage in mv
+
+Description
+-----------
+
+This driver implements support for the Texas Instruments ADS7828.
+
+This device is a 12bit 8ch A-D converter.
+
+It can operate in single ended mode (8 +ve inputs) or in differential mode,
+when 4 differential pairs can be measured.
+
+The chip also has the facility to use an external voltage reference. This
+may be required if your hardware supplies the ADS7828 from a 5v supply, see
+the datasheet for more details.
+
+
diff -puN drivers/hwmon/Kconfig~hwmon-new-chip-driver-for-ti-ads7828-a-d drivers/hwmon/Kconfig
--- a/drivers/hwmon/Kconfig~hwmon-new-chip-driver-for-ti-ads7828-a-d
+++ a/drivers/hwmon/Kconfig
@@ -588,6 +588,16 @@ config SENSORS_SMSC47B397
This driver can also be built as a module. If so, the module
will be called smsc47b397.
+config SENSORS_ADS7828
+ tristate "Texas Instruments ADS7828"
+ depends on I2C
+ help
+ If you say yes here you get support for Texas Instruments ADS7828
+ 12-bit 8-channel ADC device.
+
+ This driver can also be built as a module. If so, the module
+ will be called ads7828.
+
config SENSORS_THMC50
tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
depends on I2C && EXPERIMENTAL
diff -puN drivers/hwmon/Makefile~hwmon-new-chip-driver-for-ti-ads7828-a-d drivers/hwmon/Makefile
--- a/drivers/hwmon/Makefile~hwmon-new-chip-driver-for-ti-ads7828-a-d
+++ a/drivers/hwmon/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_SENSORS_ADM1026) += adm1026
obj-$(CONFIG_SENSORS_ADM1029) += adm1029.o
obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o
obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o
+obj-$(CONFIG_SENSORS_ADS7828) += ads7828.o
obj-$(CONFIG_SENSORS_ADT7470) += adt7470.o
obj-$(CONFIG_SENSORS_APPLESMC) += applesmc.o
obj-$(CONFIG_SENSORS_AMS) += ams/
diff -puN /dev/null drivers/hwmon/ads7828.c
--- /dev/null
+++ a/drivers/hwmon/ads7828.c
@@ -0,0 +1,296 @@
+/*
+ ads7828.c - lm_sensors driver for ads7828 12bit 8ch ADC
+ (C) 2007 EADS Astrium
+
+ This driver is based on the lm75 and other lm_sensors/hwmon drivers
+
+ Written by Steve Hardy <steve@xxxxxxxxxxxxxxxxxxx>
+
+ Datasheet available at : http://focus.ti.com/lit/ds/symlink/ads7828.pdf
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+
+/* The ADS7828 registers */
+#define ADS7828_NCH 8 /* 8 channels of 12bit A-D supported */
+#define ADS7828_CMD_SD_SE 0x80 /* Single ended inputs */
+#define ADS7828_CMD_SD_DIFF 0x00 /* Differential inputs */
+#define ADS7828_CMD_PD0 0x0 /* Power Down between A-D conversions */
+#define ADS7828_CMD_PD1 0x04 /* Internal ref OFF && A-D ON */
+#define ADS7828_CMD_PD2 0x08 /* Internal ref ON && A-D OFF */
+#define ADS7828_CMD_PD3 0x0C /* Internal ref ON && A-D ON */
+#define ADS7828_INT_VREF_MV 2500 /* Internal vref is 2.5v, 2500mV */
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b,
+ I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(ads7828);
+
+/* Other module parameters */
+static int se_input = 1; /* Default is SE, 0 == diff */
+static int int_vref = 1; /* Default is internal ref ON */
+static int vref_mv = ADS7828_INT_VREF_MV; /* set if vref != 2.5v */
+module_param(se_input, bool, S_IRUGO);
+module_param(int_vref, bool, S_IRUGO);
+module_param(vref_mv, int, S_IRUGO);
+
+/* Global Variables */
+static u8 ads7828_cmd_byte; /* cmd byte without channel bits */
+static unsigned int ads7828_lsb_resol; /* resolution of the ADC sample lsb */
+
+/* Each client has this additional data */
+struct ads7828_data {
+ struct i2c_client client;
+ struct device *hwmon_dev;
+ struct mutex update_lock; /* mutex protect updates */
+ char valid; /* !=0 if following fields are valid */
+ unsigned long last_updated; /* In jiffies */
+ u16 adc_input[ADS7828_NCH]; /* ADS7828_NCH 12bit samples */
+};
+
+/* Function declaration - neccesary due to function dependencies */
+static int ads7828_detect(struct i2c_adapter *adapter, int address, int kind);
+
+/* The ADS7828 returns the 12bit sample in two bytes,
+ these are read as a word then byte-swapped */
+static u16 ads7828_read_value(struct i2c_client *client, u8 reg)
+{
+ return swab16(i2c_smbus_read_word_data(client, reg));
+}
+
+static inline u8 channel_cmd_byte(int ch)
+{
+ /* cmd byte C2,C1,C0 - see datasheet */
+ u8 cmd = (((ch>>1) | (ch&0x01)<<2)<<4);
+ cmd |= ads7828_cmd_byte;
+ return cmd;
+}
+
+/* Update data for the device (all 8 channels) */
+static struct ads7828_data *ads7828_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct ads7828_data *data = i2c_get_clientdata(client);
+
+ mutex_lock(&data->update_lock);
+
+ if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
+ || !data->valid) {
+ unsigned int ch;
+ dev_dbg(&client->dev, "Starting ads7828 update\n");
+
+ for (ch = 0; ch < ADS7828_NCH; ch++) {
+ u8 cmd = channel_cmd_byte(ch);
+ data->adc_input[ch] = ads7828_read_value(client, cmd);
+ }
+ data->last_updated = jiffies;
+ data->valid = 1;
+ }
+
+ mutex_unlock(&data->update_lock);
+
+ return data;
+}
+
+/* sysfs callback function */
+static ssize_t show_in(struct device *dev, struct device_attribute *da,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+ struct ads7828_data *data = ads7828_update_device(dev);
+ /* Print value (in mv as specified in sysfs-interface documentation) */
+ return sprintf(buf, "%d\n", (data->adc_input[attr->index] *
+ ads7828_lsb_resol)/1000);
+}
+
+#define in_reg(offset)\
+static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO, show_in,\
+ NULL, offset);
+
+in_reg(0);
+in_reg(1);
+in_reg(2);
+in_reg(3);
+in_reg(4);
+in_reg(5);
+in_reg(6);
+in_reg(7);
+
+static struct attribute *ads7828_attributes[] = {
+ &sensor_dev_attr_in0_input.dev_attr.attr,
+ &sensor_dev_attr_in1_input.dev_attr.attr,
+ &sensor_dev_attr_in2_input.dev_attr.attr,
+ &sensor_dev_attr_in3_input.dev_attr.attr,
+ &sensor_dev_attr_in4_input.dev_attr.attr,
+ &sensor_dev_attr_in5_input.dev_attr.attr,
+ &sensor_dev_attr_in6_input.dev_attr.attr,
+ &sensor_dev_attr_in7_input.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group ads7828_group = {
+ .attrs = ads7828_attributes,
+};
+
+static int ads7828_attach_adapter(struct i2c_adapter *adapter)
+{
+ if (!(adapter->class & I2C_CLASS_HWMON))
+ return 0;
+ return i2c_probe(adapter, &addr_data, ads7828_detect);
+}
+
+static int ads7828_detach_client(struct i2c_client *client)
+{
+ struct ads7828_data *data = i2c_get_clientdata(client);
+ hwmon_device_unregister(data->hwmon_dev);
+ sysfs_remove_group(&client->dev.kobj, &ads7828_group);
+ i2c_detach_client(client);
+ kfree(i2c_get_clientdata(client));
+ return 0;
+}
+
+/* This is the driver that will be inserted */
+static struct i2c_driver ads7828_driver = {
+ .driver = {
+ .name = "ads7828",
+ },
+ .attach_adapter = ads7828_attach_adapter,
+ .detach_client = ads7828_detach_client,
+};
+
+/* This function is called by i2c_detect */
+static int ads7828_detect(struct i2c_adapter *adapter, int address, int kind)
+{
+ struct i2c_client *client;
+ struct ads7828_data *data;
+ int err=0;
+ const char *name = "";
+
+ /* Check we have a valid client */
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA))
+ goto exit;
+
+ /* OK. For now, we presume we have a valid client. We now create the
+ client structure, even though we cannot fill it completely yet.
+ But it allows us to access ads7828_read_value. */
+ data = kzalloc(sizeof(struct ads7828_data), GFP_KERNEL);
+ if (!data) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ client = &data->client;
+ i2c_set_clientdata(client, data);
+ client->addr = address;
+ client->adapter = adapter;
+ client->driver = &ads7828_driver;
+
+ /* Now, we do the remaining detection. There is no identification
+ dedicated register so attempt to sanity check using knowledge of the chip
+ - Read from the 8 channel addresses
+ - Check the top 4 bits of each result are not set (12 data bits)
+ */
+ if (kind < 0) {
+ int ch;
+ for (ch = 0; ch < ADS7828_NCH; ch++) {
+ u16 in_data;
+ u8 cmd = channel_cmd_byte(ch);
+ in_data = ads7828_read_value(client, cmd);
+ if (in_data & 0xF000) {
+ printk(KERN_DEBUG
+ "%s : Doesn't look like an ads7828 device\n",
+ __FUNCTION__);
+ goto exit_free;
+ }
+ }
+ }
+
+ /* Determine the chip type - only one kind supported! */
+ if (kind <= 0)
+ kind = ads7828;
+
+ if (kind == ads7828)
+ name = "ads7828";
+
+ /* Fill in the remaining client fields, put it into the global list */
+ strlcpy(client->name, name, I2C_NAME_SIZE);
+
+ mutex_init(&data->update_lock);
+
+ /* Tell the I2C layer a new client has arrived */
+ err = i2c_attach_client(client);
+ if (err)
+ goto exit_free;
+
+ /* Register sysfs hooks */
+ err = sysfs_create_group(&client->dev.kobj, &ads7828_group);
+ if (err)
+ goto exit_detach;
+
+ data->hwmon_dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ goto exit_remove;
+ }
+
+ return 0;
+
+exit_remove:
+ sysfs_remove_group(&client->dev.kobj, &ads7828_group);
+exit_detach:
+ i2c_detach_client(client);
+exit_free:
+ kfree(data);
+exit:
+ return err;
+}
+
+static int __init sensors_ads7828_init(void)
+{
+ /* Initialise the command byte according to module parameters */
+ ads7828_cmd_byte = se_input ?
+ ADS7828_CMD_SD_SE : ADS7828_CMD_SD_DIFF;
+ ads7828_cmd_byte |= int_vref ?
+ ADS7828_CMD_PD3 : ADS7828_CMD_PD1;
+
+ /* Calculate the LSB resolution */
+ ads7828_lsb_resol = (vref_mv*1000)/4096;
+
+ return i2c_add_driver(&ads7828_driver);
+}
+
+static void __exit sensors_ads7828_exit(void)
+{
+ i2c_del_driver(&ads7828_driver);
+}
+
+MODULE_AUTHOR("Steve Hardy <steve@xxxxxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("ADS7828 driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_ads7828_init);
+module_exit(sensors_ads7828_exit);
_
Patches currently in -mm which might be from steve@xxxxxxxxxxxxxxxxxxx are
hwmon-new-chip-driver-for-ti-ads7828-a-d.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
