The patch titled
tdfxfb: hardware cursor
has been removed from the -mm tree. Its filename was
tdfxfb-hardware-cursor.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
Subject: tdfxfb: hardware cursor
From: Krzysztof Helt <krzysztof.h1@xxxxx>
This patch adds hardware cursor support to the tdfxfb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@xxxxx>
Signed-off-by: Antonino Daplas <adaplas@xxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/video/tdfxfb.c | 169 +++++++++++++++++----------------------
include/video/tdfx.h | 8 -
2 files changed, 74 insertions(+), 103 deletions(-)
diff -puN drivers/video/tdfxfb.c~tdfxfb-hardware-cursor drivers/video/tdfxfb.c
--- a/drivers/video/tdfxfb.c~tdfxfb-hardware-cursor
+++ a/drivers/video/tdfxfb.c
@@ -67,7 +67,6 @@
#include <linux/init.h>
#include <linux/pci.h>
#include <asm/io.h>
-#include <linux/timer.h>
#include <linux/spinlock.h>
#include <video/tdfx.h>
@@ -148,8 +147,9 @@ MODULE_DEVICE_TABLE(pci, tdfxfb_id_table
/*
* Driver data
*/
-static int nopan = 0;
-static int nowrap = 1; // not implemented (yet)
+static int nopan;
+static int nowrap = 1; /* not implemented (yet) */
+static int hwcursor = 1;
static char *mode_option __devinitdata = NULL;
/* -------------------------------------------------------------------------
@@ -378,7 +378,7 @@ static void do_write_regs(struct fb_info
tdfx_outl(par, VGAINIT0, reg->vgainit0);
tdfx_outl(par, DACMODE, reg->dacmode);
tdfx_outl(par, VIDDESKSTRIDE, reg->stride);
- tdfx_outl(par, HWCURPATADDR, 0);
+ tdfx_outl(par, HWCURPATADDR, reg->curspataddr);
tdfx_outl(par, VIDSCREENSIZE, reg->screensize);
tdfx_outl(par, VIDDESKSTART, reg->startaddr);
@@ -453,6 +453,7 @@ static int tdfxfb_check_var(struct fb_va
DPRINTK("xoffset not supported\n");
return -EINVAL;
}
+ var->yoffset = 0;
/* Banshee doesn't support interlace, but Voodoo4/5 and probably Voodoo3 do. */
/* no direct information about device id now? use max_pixclock for this... */
@@ -663,6 +664,9 @@ static int tdfxfb_set_par(struct fb_info
VGAINIT0_EXTSHIFTOUT;
reg.vgainit1 = tdfx_inl(par, VGAINIT1) & 0x1fffff;
+ if (hwcursor)
+ reg.curspataddr = info->fix.smem_len;
+
reg.cursloc = 0;
reg.cursc0 = 0;
@@ -1012,11 +1016,25 @@ static void tdfxfb_imageblit(struct fb_i
}
#endif /* CONFIG_FB_3DFX_ACCEL */
-#ifdef TDFX_HARDWARE_CURSOR
static int tdfxfb_cursor(struct fb_info *info, struct fb_cursor *cursor)
{
struct tdfx_par *par = info->par;
- unsigned long flags;
+ u32 vidcfg;
+
+ if (!hwcursor)
+ return -EINVAL; /* just to force soft_cursor() call */
+
+ /* Too large of a cursor or wrong bpp :-( */
+ if (cursor->image.width > 64 ||
+ cursor->image.height > 64 ||
+ cursor->image.depth > 1)
+ return -EINVAL;
+
+ vidcfg = tdfx_inl(par, VIDPROCCFG);
+ if (cursor->enable)
+ tdfx_outl(par, VIDPROCCFG, vidcfg | VIDCFG_HWCURSOR_ENABLE);
+ else
+ tdfx_outl(par, VIDPROCCFG, vidcfg & ~VIDCFG_HWCURSOR_ENABLE);
/*
* If the cursor is not be changed this means either we want the
@@ -1026,69 +1044,34 @@ static int tdfxfb_cursor(struct fb_info
if (!cursor->set)
return 0;
- /* Too large of a cursor :-( */
- if (cursor->image.width > 64 || cursor->image.height > 64)
- return -ENXIO;
-
- /*
- * If we are going to be changing things we should disable
- * the cursor first
- */
- if (info->cursor.enable) {
- spin_lock_irqsave(&par->DAClock, flags);
- info->cursor.enable = 0;
- del_timer(&(par->hwcursor.timer));
- tdfx_outl(par, VIDPROCCFG, par->hwcursor.disable);
- spin_unlock_irqrestore(&par->DAClock, flags);
- }
-
- /* Disable the Cursor */
- if ((cursor->set && FB_CUR_SETCUR) && !cursor->enable)
- return 0;
-
/* fix cursor color - XFree86 forgets to restore it properly */
- if (cursor->set && FB_CUR_SETCMAP) {
- struct fb_cmap cmap = cursor->image.cmap;
+ if (cursor->set & FB_CUR_SETCMAP) {
+ struct fb_cmap cmap = info->cmap;
+ u32 bg_idx = cursor->image.bg_color;
+ u32 fg_idx = cursor->image.fg_color;
unsigned long bg_color, fg_color;
- cmap.len = 2; /* Voodoo 3+ only support 2 color cursors */
- fg_color = ((cmap.red[cmap.start] << 16) |
- (cmap.green[cmap.start] << 8) |
- (cmap.blue[cmap.start]));
- bg_color = ((cmap.red[cmap.start + 1] << 16) |
- (cmap.green[cmap.start + 1] << 8) |
- (cmap.blue[cmap.start + 1]));
- fb_copy_cmap(&cmap, &info->cursor.image.cmap);
- spin_lock_irqsave(&par->DAClock, flags);
+ fg_color = (((u32)cmap.red[fg_idx] & 0xff00) << 8) |
+ (((u32)cmap.green[fg_idx] & 0xff00) << 0) |
+ (((u32)cmap.blue[fg_idx] & 0xff00) >> 8);
+ bg_color = (((u32)cmap.red[bg_idx] & 0xff00) << 8) |
+ (((u32)cmap.green[bg_idx] & 0xff00) << 0) |
+ (((u32)cmap.blue[bg_idx] & 0xff00) >> 8);
banshee_make_room(par, 2);
tdfx_outl(par, HWCURC0, bg_color);
tdfx_outl(par, HWCURC1, fg_color);
- spin_unlock_irqrestore(&par->DAClock, flags);
}
- if (cursor->set && FB_CUR_SETPOS) {
- int x, y;
+ if (cursor->set & FB_CUR_SETPOS) {
+ int x = cursor->image.dx;
+ int y = cursor->image.dy - info->var.yoffset;
- x = cursor->image.dx;
- y = cursor->image.dy;
- y -= info->var.yoffset;
- info->cursor.image.dx = x;
- info->cursor.image.dy = y;
x += 63;
y += 63;
- spin_lock_irqsave(&par->DAClock, flags);
banshee_make_room(par, 1);
tdfx_outl(par, HWCURLOC, (y << 16) + x);
- spin_unlock_irqrestore(&par->DAClock, flags);
}
-
- /* Not supported so we fake it */
- if (cursor->set && FB_CUR_SETHOT) {
- info->cursor.hot.x = cursor->hot.x;
- info->cursor.hot.y = cursor->hot.y;
- }
-
- if (cursor->set && FB_CUR_SETSHAPE) {
+ if (cursor->set & (FB_CUR_SETIMAGE | FB_CUR_SETSHAPE)) {
/*
* Voodoo 3 and above cards use 2 monochrome cursor patterns.
* The reason is so the card can fetch 8 words at a time
@@ -1096,7 +1079,7 @@ static int tdfxfb_cursor(struct fb_info
* This reduces the number of times for access to draw the
* cursor for each screen refresh.
* Each pattern is a bitmap of 64 bit wide and 64 bit high
- * (total of 8192 bits or 1024 Kbytes). The two patterns are
+ * (total of 8192 bits or 1024 bytes). The two patterns are
* stored in such a way that pattern 0 always resides in the
* lower half (least significant 64 bits) of a 128 bit word
* and pattern 1 the upper half. If you examine the data of
@@ -1107,50 +1090,34 @@ static int tdfxfb_cursor(struct fb_info
* (128 bits) which is the maximum cursor width times two for
* the two monochrome patterns.
*/
- u8 *cursorbase = (u8 *)info->cursor.image.data;
- char *bitmap = (char *)cursor->image.data;
- char *mask = (char *)cursor->mask;
- int i, j, k, h = 0;
-
- for (i = 0; i < 64; i++) {
- if (i < cursor->image.height) {
- j = (cursor->image.width + 7) >> 3;
- k = 8 - j;
-
- for (; j > 0; j--) {
- /* Pattern 0. Copy the cursor bitmap to it */
- fb_writeb(*bitmap, cursorbase + h);
- bitmap++;
- /* Pattern 1. Copy the cursor mask to it */
- fb_writeb(*mask, cursorbase + h + 8);
- mask++;
- h++;
- }
- for (; k > 0; k--) {
- fb_writeb(0, cursorbase + h);
- fb_writeb(~0, cursorbase + h + 8);
- h++;
- }
- } else {
- fb_writel(0, cursorbase + h);
- fb_writel(0, cursorbase + h + 4);
- fb_writel(~0, cursorbase + h + 8);
- fb_writel(~0, cursorbase + h + 12);
- h += 16;
+ u8 __iomem *cursorbase = info->screen_base + info->fix.smem_len;
+ u8 *bitmap = (u8 *)cursor->image.data;
+ u8 *mask = (u8 *)cursor->mask;
+ int i;
+
+ fb_memset(cursorbase, 0, 1024);
+
+ for (i = 0; i < cursor->image.height; i++) {
+ int h = 0;
+ int j = (cursor->image.width + 7) >> 3;
+
+ for (; j > 0; j--) {
+ u8 data = *mask ^ *bitmap;
+ if (cursor->rop == ROP_COPY)
+ data = *mask & *bitmap;
+ /* Pattern 0. Copy the cursor mask to it */
+ fb_writeb(*mask, cursorbase + h);
+ mask++;
+ /* Pattern 1. Copy the cursor bitmap to it */
+ fb_writeb(data, cursorbase + h + 8);
+ bitmap++;
+ h++;
}
+ cursorbase += 16;
}
}
- /* Turn the cursor on */
- cursor->enable = 1;
- info->cursor = *cursor;
- mod_timer(&par->hwcursor.timer, jiffies + HZ / 2);
- spin_lock_irqsave(&par->DAClock, flags);
- banshee_make_room(par, 1);
- tdfx_outl(par, VIDPROCCFG, par->hwcursor.enable);
- spin_unlock_irqrestore(&par->DAClock, flags);
return 0;
}
-#endif
static struct fb_ops tdfxfb_ops = {
.owner = THIS_MODULE,
@@ -1160,6 +1127,7 @@ static struct fb_ops tdfxfb_ops = {
.fb_blank = tdfxfb_blank,
.fb_pan_display = tdfxfb_pan_display,
.fb_sync = banshee_wait_idle,
+ .fb_cursor = tdfxfb_cursor,
#ifdef CONFIG_FB_3DFX_ACCEL
.fb_fillrect = tdfxfb_fillrect,
.fb_copyarea = tdfxfb_copyarea,
@@ -1272,6 +1240,11 @@ static int __devinit tdfxfb_probe(struct
FBINFO_HWACCEL_IMAGEBLIT |
FBINFO_READS_FAST;
#endif
+ /* reserve 8192 bits for cursor */
+ /* the 2.4 driver says PAGE_MASK boundary is not enough for Voodoo4 */
+ if (hwcursor)
+ info->fix.smem_len = (info->fix.smem_len - 1024) &
+ (PAGE_MASK << 1);
if (!mode_option)
mode_option = "640x480@60";
@@ -1336,6 +1309,8 @@ static void tdfxfb_setup(char *options)
nopan = 1;
} else if (!strcmp(this_opt, "nowrap")) {
nowrap = 1;
+ } else if (!strcmp(this_opt, "hwcursor")) {
+ hwcursor = simple_strtoul(opt + 9, NULL, 0);
} else {
mode_option = this_opt;
}
@@ -1394,5 +1369,9 @@ MODULE_AUTHOR("Hannu Mallat <hmallat@cc.
MODULE_DESCRIPTION("3Dfx framebuffer device driver");
MODULE_LICENSE("GPL");
+module_param(hwcursor, int, 0644);
+MODULE_PARM_DESC(hwcursor, "Enable hardware cursor "
+ "(1=enable, 0=disable, default=1)");
+
module_init(tdfxfb_init);
module_exit(tdfxfb_exit);
diff -puN include/video/tdfx.h~tdfxfb-hardware-cursor include/video/tdfx.h
--- a/include/video/tdfx.h~tdfxfb-hardware-cursor
+++ a/include/video/tdfx.h
@@ -175,14 +175,6 @@ struct tdfx_par {
u32 palette[16];
void __iomem *regbase_virt;
unsigned long iobase;
-
- struct {
- int w, u, d;
- unsigned long enable, disable;
- struct timer_list timer;
- } hwcursor;
-
- spinlock_t DAClock;
};
#endif /* __KERNEL__ */
_
Patches currently in -mm which might be from krzysztof.h1@xxxxx are
origin.patch
git-alsa.patch
cyber2000fb-checkpatch-fixes.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
