The patch titled
SPI controller drivers: check for unsupported modes
has been removed from the -mm tree. Its filename was
spi-controller-drivers-check-for-unsupported-modes.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
Subject: SPI controller drivers: check for unsupported modes
From: David Brownell <david-b@xxxxxxxxxxx>
Minor SPI controller driver updates: make the setup() methods reject
spi->mode bits they don't support, by masking aginst the inverse of bits
they *do* support. This insures against misbehavior later when new mode
bits get added.
Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH.
Support for all four SPI clock/transfer modes is routine.
Signed-off-by: David Brownell <dbrownell@xxxxxxxxxxxxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/spi/atmel_spi.c | 1 +
drivers/spi/au1550_spi.c | 9 +++++++++
drivers/spi/mpc52xx_psc_spi.c | 9 +++++++++
drivers/spi/omap_uwire.c | 9 +++++++++
drivers/spi/pxa2xx_spi.c | 9 +++++++++
drivers/spi/spi_bitbang.c | 8 +++-----
drivers/spi/spi_imx.c | 24 +++++++++---------------
drivers/spi/spi_mpc83xx.c | 9 +++++++++
drivers/spi/spi_s3c24xx.c | 8 +++++++-
include/linux/spi/spi_bitbang.h | 1 +
10 files changed, 66 insertions(+), 21 deletions(-)
diff -puN drivers/spi/atmel_spi.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/atmel_spi.c
--- a/drivers/spi/atmel_spi.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/atmel_spi.c
@@ -350,6 +350,7 @@ atmel_spi_interrupt(int irq, void *dev_i
return ret;
}
+/* the spi->mode bits understood by this driver: */
#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
static int atmel_spi_setup(struct spi_device *spi)
diff -puN drivers/spi/au1550_spi.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/au1550_spi.c
--- a/drivers/spi/au1550_spi.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/au1550_spi.c
@@ -280,6 +280,9 @@ static int au1550_spi_setupxfer(struct s
return 0;
}
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LSB_FIRST)
+
static int au1550_spi_setup(struct spi_device *spi)
{
struct au1550_spi *hw = spi_master_get_devdata(spi->master);
@@ -292,6 +295,12 @@ static int au1550_spi_setup(struct spi_d
return -EINVAL;
}
+ if (spi->mode & ~MODEBITS) {
+ dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode & ~MODEBITS);
+ return -EINVAL;
+ }
+
if (spi->max_speed_hz == 0)
spi->max_speed_hz = hw->freq_max;
if (spi->max_speed_hz > hw->freq_max
diff -puN drivers/spi/mpc52xx_psc_spi.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/mpc52xx_psc_spi.c
--- a/drivers/spi/mpc52xx_psc_spi.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/mpc52xx_psc_spi.c
@@ -270,6 +270,9 @@ static void mpc52xx_psc_spi_work(struct
spin_unlock_irq(&mps->lock);
}
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LSB_FIRST)
+
static int mpc52xx_psc_spi_setup(struct spi_device *spi)
{
struct mpc52xx_psc_spi *mps = spi_master_get_devdata(spi->master);
@@ -279,6 +282,12 @@ static int mpc52xx_psc_spi_setup(struct
if (spi->bits_per_word%8)
return -EINVAL;
+ if (spi->mode & ~MODEBITS) {
+ dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode & ~MODEBITS);
+ return -EINVAL;
+ }
+
if (!cs) {
cs = kzalloc(sizeof *cs, GFP_KERNEL);
if (!cs)
diff -puN drivers/spi/omap_uwire.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/omap_uwire.c
--- a/drivers/spi/omap_uwire.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/omap_uwire.c
@@ -445,10 +445,19 @@ done:
return status;
}
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
+
static int uwire_setup(struct spi_device *spi)
{
struct uwire_state *ust = spi->controller_state;
+ if (spi->mode & ~MODEBITS) {
+ dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode & ~MODEBITS);
+ return -EINVAL;
+ }
+
if (ust == NULL) {
ust = kzalloc(sizeof(*ust), GFP_KERNEL);
if (ust == NULL)
diff -puN drivers/spi/pxa2xx_spi.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/pxa2xx_spi.c
--- a/drivers/spi/pxa2xx_spi.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/pxa2xx_spi.c
@@ -1067,6 +1067,9 @@ static int transfer(struct spi_device *s
return 0;
}
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA)
+
static int setup(struct spi_device *spi)
{
struct pxa2xx_spi_chip *chip_info = NULL;
@@ -1093,6 +1096,12 @@ static int setup(struct spi_device *spi)
return -EINVAL;
}
+ if (spi->mode & ~MODEBITS) {
+ dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode & ~MODEBITS);
+ return -EINVAL;
+ }
+
/* Only alloc on first setup */
chip = spi_get_ctldata(spi);
if (!chip) {
diff -puN drivers/spi/spi_bitbang.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/spi_bitbang.c
--- a/drivers/spi/spi_bitbang.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/spi_bitbang.c
@@ -187,12 +187,10 @@ int spi_bitbang_setup(struct spi_device
bitbang = spi_master_get_devdata(spi->master);
- /* REVISIT: some systems will want to support devices using lsb-first
- * bit encodings on the wire. In pure software that would be trivial,
- * just bitbang_txrx_le_cphaX() routines shifting the other way, and
- * some hardware controllers also have this support.
+ /* Bitbangers can support SPI_CS_HIGH, SPI_3WIRE, and so on;
+ * add those to master->flags, and provide the other support.
*/
- if ((spi->mode & SPI_LSB_FIRST) != 0)
+ if ((spi->mode & ~(SPI_CPOL|SPI_CPHA|bitbang->flags)) != 0)
return -EINVAL;
if (!cs) {
diff -puN drivers/spi/spi_imx.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/spi_imx.c
--- a/drivers/spi/spi_imx.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/spi_imx.c
@@ -1163,6 +1163,9 @@ msg_rejected:
return -EINVAL;
}
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
+
/* On first setup bad values must free chip_data memory since will cause
spi_new_device to fail. Bad value setup from protocol driver are simply not
applied and notified to the calling driver. */
@@ -1174,6 +1177,12 @@ static int setup(struct spi_device *spi)
u32 tmp;
int status = 0;
+ if (spi->mode & ~MODEBITS) {
+ dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode & ~MODEBITS);
+ return -EINVAL;
+ }
+
/* Get controller data */
chip_info = spi->controller_data;
@@ -1245,21 +1254,6 @@ static int setup(struct spi_device *spi)
/* SPI mode */
tmp = spi->mode;
- if (tmp & SPI_LSB_FIRST) {
- status = -EINVAL;
- if (first_setup) {
- dev_err(&spi->dev,
- "setup - "
- "HW doesn't support LSB first transfer\n");
- goto err_first_setup;
- } else {
- dev_err(&spi->dev,
- "setup - "
- "HW doesn't support LSB first transfer, "
- "default to MSB first\n");
- spi->mode &= ~SPI_LSB_FIRST;
- }
- }
if (tmp & SPI_CS_HIGH) {
u32_EDIT(chip->control,
SPI_CONTROL_SSPOL, SPI_CONTROL_SSPOL_ACT_HIGH);
diff -puN drivers/spi/spi_mpc83xx.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/spi_mpc83xx.c
--- a/drivers/spi/spi_mpc83xx.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/spi_mpc83xx.c
@@ -232,12 +232,21 @@ int mpc83xx_spi_setup_transfer(struct sp
return 0;
}
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
+
static int mpc83xx_spi_setup(struct spi_device *spi)
{
struct spi_bitbang *bitbang;
struct mpc83xx_spi *mpc83xx_spi;
int retval;
+ if (spi->mode & ~MODEBITS) {
+ dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode & ~MODEBITS);
+ return -EINVAL;
+ }
+
if (!spi->max_speed_hz)
return -EINVAL;
diff -puN drivers/spi/spi_s3c24xx.c~spi-controller-drivers-check-for-unsupported-modes drivers/spi/spi_s3c24xx.c
--- a/drivers/spi/spi_s3c24xx.c~spi-controller-drivers-check-for-unsupported-modes
+++ a/drivers/spi/spi_s3c24xx.c
@@ -146,6 +146,9 @@ static int s3c24xx_spi_setupxfer(struct
return 0;
}
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
+
static int s3c24xx_spi_setup(struct spi_device *spi)
{
int ret;
@@ -153,8 +156,11 @@ static int s3c24xx_spi_setup(struct spi_
if (!spi->bits_per_word)
spi->bits_per_word = 8;
- if ((spi->mode & SPI_LSB_FIRST) != 0)
+ if (spi->mode & ~MODEBITS) {
+ dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode & ~MODEBITS);
return -EINVAL;
+ }
ret = s3c24xx_spi_setupxfer(spi, NULL);
if (ret < 0) {
diff -puN include/linux/spi/spi_bitbang.h~spi-controller-drivers-check-for-unsupported-modes include/linux/spi/spi_bitbang.h
--- a/include/linux/spi/spi_bitbang.h~spi-controller-drivers-check-for-unsupported-modes
+++ a/include/linux/spi/spi_bitbang.h
@@ -26,6 +26,7 @@ struct spi_bitbang {
struct list_head queue;
u8 busy;
u8 use_dma;
+ u8 flags; /* extra spi->mode support */
struct spi_master *master;
_
Patches currently in -mm which might be from david-b@xxxxxxxxxxx are
origin.patch
git-leds.patch
git-mmc.patch
git-mtd.patch
git-backlight.patch
use-mutex-instead-of-semaphore-in-the-usb-gadget-serial-driver.patch
geode-basic-infrastructure-support-for-amd-geode-class.patch
drivers-pmc-msp71xx-gpio-char-driver.patch
gpio-calls-dont-need-i-o-barriers.patch
dev_vdbg-available-with-dverbose_debug.patch
dev_vdbg-available-with-dverbose_debug-docs.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
