The patch titled
pata_artop: remove all the crud again and restore the cable method
has been removed from the -mm tree. Its filename was
pata_artop-remove-all-the-crud-again-and-restore-the-cable.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
Subject: pata_artop: remove all the crud again and restore the cable method
From: Alan Cox <alan@xxxxxxxxxx>
Signed-off-by: Alan Cox <alan@xxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/ata/pata_artop.c | 26 ++++++++++++++++++--------
1 file changed, 18 insertions(+), 8 deletions(-)
diff -puN drivers/ata/pata_artop.c~pata_artop-remove-all-the-crud-again-and-restore-the-cable drivers/ata/pata_artop.c
--- a/drivers/ata/pata_artop.c~pata_artop-remove-all-the-crud-again-and-restore-the-cable
+++ a/drivers/ata/pata_artop.c
@@ -49,8 +49,6 @@ static int artop6210_pre_reset(struct at
if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
return -ENOENT;
-
- ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap, deadline);
}
@@ -86,18 +84,28 @@ static int artop6260_pre_reset(struct at
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u8 tmp;
/* Odd numbered device ids are the units with enable bits (the -R cards) */
if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
return -ENOENT;
+ return ata_std_prereset(ap, deadline);
+}
+
+/**
+ * artop6260_cable_detect - identify cable type
+ * @ap: Port
+ *
+ * Identify the cable type for the ARTOp interface in question
+ */
+static int artop6260_cable_detect(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 tmp;
pci_read_config_byte(pdev, 0x49, &tmp);
if (tmp & (1 << ap->port_no))
- ap->cbl = ATA_CBL_PATA40;
- else
- ap->cbl = ATA_CBL_PATA80;
- return ata_std_prereset(ap, deadline);
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
}
/**
@@ -226,7 +234,7 @@ static void artop6260_set_piomode(struct
/**
* artop6210_set_dmamode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
- * @adev: um
+ * @adev: Device whose timings we are configuring
*
* Set DMA mode for device, in host controller PCI config space.
*
@@ -334,6 +342,7 @@ static const struct ata_port_operations
.thaw = ata_bmdma_thaw,
.error_handler = artop6210_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -367,6 +376,7 @@ static const struct ata_port_operations
.thaw = ata_bmdma_thaw,
.error_handler = artop6260_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = artop6260_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
_
Patches currently in -mm which might be from alan@xxxxxxxxxx are
origin.patch
git-libata-all.patch
pcmcia-spot-slave-decode-flaws-for-testing.patch
ata_generic-remove-all-the-crud-again-and-use-cable.patch
pata_ali-remove-all-the-crap-again-and-switch-to.patch
pata_amd-remove-all-the-crud-and-restore-the-cable-detect.patch
pata_cs5535-re-remove-all-the-crap-and-switch-to-the-cable.patch
pata_cypress-re-remove-all-the-crap-and-switch-back-to.patch
pata_netcell-re-remove-all-the-crud.patch
pata_qdi-restore-cable-detect.patch
pata_sl82c105-restore-cable-detect-method.patch
pata_winbond-restore-cable-method.patch
libata-acpi-add-infrastructure-for-drivers-to-use.patch
pata_optidma-rework-for-cable-detect-and-to-remove.patch
pata_pdc2027x-restore-various-updates-done-on-the-driver.patch
pata_acpi-restore-driver.patch
resend-iphase-64bit-cleanup.patch
pci_module_init-convertion-in-tmscsimc.patch
tty-clarify-documentation-of-write.patch
tty-i386-x86_64-arbitary-speed-support.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
