The patch titled
pata_sis: clean up using cable_detect methods
has been removed from the -mm tree. Its filename was
pata_sis-clean-up-using-cable_detect-methods.patch
This patch was dropped because an updated version will be merged
------------------------------------------------------
Subject: pata_sis: clean up using cable_detect methods
From: Alan Cox <alan@xxxxxxxxxxxxxxxxxxx>
This changeset revolves around the fact that all the SiS controllers have the
same enable bits, but differing cable detection methods. Previously that
meant each type had its own error_handler methods. Instead we can now
implement different ->cable_detect methods and share a single error_handler
which does the filtering by enable bits.
In addition we had some auto const arrays that should be static const. I'm
not sure if gcc already treats them intelligently but adding the static will
make sure.
Signed-off-by: Alan Cox <alan@xxxxxxxxxx>
Cc: Jeff Garzik <jeff@xxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/ata/pata_sis.c | 109 ++++++++++-----------------------------
1 files changed, 29 insertions(+), 80 deletions(-)
diff -puN drivers/ata/pata_sis.c~pata_sis-clean-up-using-cable_detect-methods drivers/ata/pata_sis.c
--- a/drivers/ata/pata_sis.c~pata_sis-clean-up-using-cable_detect-methods
+++ a/drivers/ata/pata_sis.c
@@ -35,7 +35,7 @@
#include "sis.h"
#define DRV_NAME "pata_sis"
-#define DRV_VERSION "0.5.0"
+#define DRV_VERSION "0.5.1"
struct sis_chipset {
u16 device; /* PCI host ID */
@@ -86,106 +86,55 @@ static int sis_port_base(struct ata_devi
}
/**
- * sis_133_pre_reset - check for 40/80 pin
+ * sis_133_cable_detect - check for 40/80 pin
* @ap: Port
*
* Perform cable detection for the later UDMA133 capable
* SiS chipset.
*/
-static int sis_133_pre_reset(struct ata_port *ap)
+static int sis_133_cable_detect(struct ata_port *ap)
{
- static const struct pci_bits sis_enable_bits[] = {
- { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
- { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */
- };
-
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 tmp;
- if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
- return -ENOENT;
-
/* The top bit of this register is the cable detect bit */
pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp);
if ((tmp & 0x8000) && !sis_short_ata40(pdev))
- ap->cbl = ATA_CBL_PATA40;
- else
- ap->cbl = ATA_CBL_PATA80;
-
- return ata_std_prereset(ap);
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
}
/**
- * sis_error_handler - Probe specified port on PATA host controller
- * @ap: Port to probe
- *
- * LOCKING:
- * None (inherited from caller).
- */
-
-static void sis_133_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, sis_133_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
-}
-
-
-/**
- * sis_66_pre_reset - check for 40/80 pin
+ * sis_66_cable_detect - check for 40/80 pin
* @ap: Port
*
* Perform cable detection on the UDMA66, UDMA100 and early UDMA133
* SiS IDE controllers.
*/
-static int sis_66_pre_reset(struct ata_port *ap)
+static int sis_66_cable_detect(struct ata_port *ap)
{
- static const struct pci_bits sis_enable_bits[] = {
- { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
- { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */
- };
-
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 tmp;
- if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
- ata_port_disable(ap);
- ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
- return 0;
- }
/* Older chips keep cable detect in bits 4/5 of reg 0x48 */
pci_read_config_byte(pdev, 0x48, &tmp);
tmp >>= ap->port_no;
if ((tmp & 0x10) && !sis_short_ata40(pdev))
- ap->cbl = ATA_CBL_PATA40;
- else
- ap->cbl = ATA_CBL_PATA80;
-
- return ata_std_prereset(ap);
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
}
-/**
- * sis_66_error_handler - Probe specified port on PATA host controller
- * @ap: Port to probe
- * @classes:
- *
- * LOCKING:
- * None (inherited from caller).
- */
-
-static void sis_66_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, sis_66_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
-}
/**
- * sis_old_pre_reset - probe begin
+ * sis_pre_reset - probe begin
* @ap: ATA port
*
* Set up cable type and use generic probe init
*/
-static int sis_old_pre_reset(struct ata_port *ap)
+static int sis_pre_reset(struct ata_port *ap)
{
static const struct pci_bits sis_enable_bits[] = {
{ 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
@@ -194,27 +143,23 @@ static int sis_old_pre_reset(struct ata_
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
- ata_port_disable(ap);
- ata_port_printk(ap, KERN_INFO, "port disabled. ignoring.\n");
- return 0;
- }
- ap->cbl = ATA_CBL_PATA40;
+ if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
+ return -ENOENT;
return ata_std_prereset(ap);
}
/**
- * sis_old_error_handler - Probe specified port on PATA host controller
+ * sis_error_handler - Probe specified port on PATA host controller
* @ap: Port to probe
*
* LOCKING:
* None (inherited from caller).
*/
-static void sis_old_error_handler(struct ata_port *ap)
+static void sis_error_handler(struct ata_port *ap)
{
- ata_bmdma_drive_eh(ap, sis_old_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+ ata_bmdma_drive_eh(ap, sis_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
@@ -494,7 +439,7 @@ static void sis_133_early_set_dmamode (s
int drive_pci = sis_port_base(adev);
u16 timing;
- const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
+ static const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
pci_read_config_word(pdev, drive_pci, &timing);
@@ -531,8 +476,8 @@ static void sis_133_set_dmamode (struct
u32 reg54;
/* bits 4- cycle time 8 - cvs time */
- const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
- const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
+ static const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
+ static const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
/* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
pci_read_config_dword(pdev, 0x54, ®54);
@@ -595,8 +540,9 @@ static const struct ata_port_operations
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_133_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = sis_133_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -628,8 +574,9 @@ static const struct ata_port_operations
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_66_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = sis_66_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -661,9 +608,9 @@ static const struct ata_port_operations
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_66_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
-
+ .cable_detect = sis_66_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -692,10 +639,11 @@ static const struct ata_port_operations
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
+ .cable_detect = sis_66_cable_detect,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_66_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
@@ -728,8 +676,9 @@ static const struct ata_port_operations
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sis_old_error_handler,
+ .error_handler = sis_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
_
Patches currently in -mm which might be from alan@xxxxxxxxxxxxxxxxxxx are
git-libata-all.patch
expose-set_mode-method-so-it-can-be-wrapped.patch
pcmcia-spot-slave-decode-flaws-for-testing.patch
pata_platform-set-a-cable-type-which-to-set.patch
pata_qdi-set-cable-type.patch
pata_sl82c105-missing-methods-cable.patch
pata_isapnp-set-cable-type.patch
pata_legacy-fix-missing-methods-and-add-cable-types.patch
pata_sc1200-set-cable-type-add-freeze-thaw-methods.patch
pata_winbond-set-cable-type.patch
ata_piix-remove-ugly-layering-violation.patch
pata_mpc52xx-cable-detect.patch
pata_mpiix-cable-detect-method.patch
pata_ns87410-cable-detect-method.patch
pata_oldpiix-cable-detect.patch
pata_opti-cable-detect.patch
pata_pcmcia-cable-detect.patch
pata_triflex-cable-detect.patch
pata_cmd640-multiple-updates.patch
pata_sis-clean-up-using-cable_detect-methods.patch
pata_via-use-cable_detect-method.patch
pata_hpt366-cable-detect-methods.patch
pata_atiixp-switch-to-cable_detect-method-with-correct.patch
libata-fix-hopefully-all-the-remaining-problems-with.patch
dilnetpc-fix-warning.patch
resend-iphase-64bit-cleanup.patch
serial-suppress-rts-assertion-with-disabled-crtscts.patch
drivers-scsi-ncr5380c-replacing-yield-with-a.patch
drivers-scsi-mca_53c9xc-save_flags-cli-removal.patch
x86_64-do-not-enable-the-nmi-watchdog-by-default.patch
z85230-fix-fifo-handling.patch
driver_bfin_serial_core.patch
driver_bfin_serial_core-update.patch
documentation-ask-driver-writers-to-provide-pm-support.patch
tty-clarify-documentation-of-write.patch
edac-new-opteron-athlon64-memory-controller-driver.patch
edac-k8-driver-coding-tidy.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
