The patch titled
Blackfin: blackfin i2c driver
has been added to the -mm tree. Its filename is
blackfin-blackfin-i2c-driver-update-2.patch
*** Remember to use Documentation/SubmitChecklist when testing your code ***
See http://www.zip.com.au/~akpm/linux/patches/stuff/added-to-mm.txt to find
out what to do about this
------------------------------------------------------
Subject: Blackfin: blackfin i2c driver
From: "Wu, Bryan" <bryan.wu@xxxxxxxxxx>
The i2c linux driver for blackfin architecture which supports both GPIO i2c
operation and blackfin on-chip TWI controller i2c operation.
Signed-off-by: Bryan Wu <bryan.wu@xxxxxxxxxx>
Reviewed-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
Reviewed-by: Alexey Dobriyan <adobriyan@xxxxxxxxx>
Reviewed-by: Jean Delvare <khali@xxxxxxxxxxxx>
Cc: David Brownell <david-b@xxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/i2c/busses/Kconfig | 47 ++
drivers/i2c/busses/Makefile | 2
drivers/i2c/busses/i2c-bfin-gpio.c | 100 ++++
drivers/i2c/busses/i2c-bfin-twi.c | 589 +++++++++++++++++++++++++++
4 files changed, 738 insertions(+)
diff -puN drivers/i2c/busses/Kconfig~blackfin-blackfin-i2c-driver-update-2 drivers/i2c/busses/Kconfig
--- a/drivers/i2c/busses/Kconfig~blackfin-blackfin-i2c-driver-update-2
+++ a/drivers/i2c/busses/Kconfig
@@ -91,6 +91,53 @@ config I2C_AU1550
This driver can also be built as a module. If so, the module
will be called i2c-au1550.
+config I2C_BLACKFIN_GPIO
+ tristate "Blackfin GPIO based I2C interface"
+ depends on I2C && BLACKFIN && EXPERIMENTAL
+ select I2C_ALGOBIT
+ help
+ Say Y here if you have an Blackfin BF5xx based
+ system and are using GPIO lines for an I2C bus.
+
+menu "Blackfin I2C SDA/SCL Selection"
+ depends on I2C_BLACKFIN_GPIO
+config I2C_BLACKFIN_GPIO_SDA
+ int "SDA GPIO pin number"
+ range 0 15 if (BF533 || BF532 || BF531)
+ range 0 47 if (BF534 || BF536 || BF537)
+ range 0 47 if BF561
+ default 2
+
+config I2C_BLACKFIN_GPIO_SCL
+ int "SCL GPIO pin number"
+ range 0 15 if (BF533 || BF532 || BF531)
+ range 0 47 if (BF534 || BF536 || BF537)
+ range 0 47 if BF561
+ default 3
+endmenu
+
+config I2C_BLACKFIN_GPIO_CYCLE_DELAY
+ int "Cycle Delay in uSec"
+ depends on I2C_BLACKFIN_GPIO
+ range 5 100
+ default 40
+
+config I2C_BLACKFIN_TWI
+ tristate "Blackfin TWI I2C support"
+ depends on I2C && (BF534 || BF536 || BF537)
+ help
+ This is the TWI I2C device driver for Blackfin 534/536/537.
+ This driver can also be built as a module. If so, the module
+ will be called i2c-bfin-twi.
+
+config I2C_BLACKFIN_TWI_CLK_KHZ
+ int "Blackfin TWI I2C clock (kHz)"
+ depends on I2C_BLACKFIN_TWI
+ range 10 400
+ default 50
+ help
+ The unit of the TWI clock is kilo HZ.
+
config I2C_ELEKTOR
tristate "Elektor ISA card"
depends on I2C && ISA && BROKEN_ON_SMP
diff -puN drivers/i2c/busses/Makefile~blackfin-blackfin-i2c-driver-update-2 drivers/i2c/busses/Makefile
--- a/drivers/i2c/busses/Makefile~blackfin-blackfin-i2c-driver-update-2
+++ a/drivers/i2c/busses/Makefile
@@ -10,6 +10,8 @@ obj-$(CONFIG_I2C_AMD756_S4882) += i2c-am
obj-$(CONFIG_I2C_AMD8111) += i2c-amd8111.o
obj-$(CONFIG_I2C_AT91) += i2c-at91.o
obj-$(CONFIG_I2C_AU1550) += i2c-au1550.o
+obj-$(CONFIG_I2C_BLACKFIN_GPIO) += i2c-bfin-gpio.o
+obj-$(CONFIG_I2C_BLACKFIN_TWI) += i2c-bfin-twi.o
obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o
obj-$(CONFIG_I2C_HYDRA) += i2c-hydra.o
obj-$(CONFIG_I2C_I801) += i2c-i801.o
diff -puN /dev/null drivers/i2c/busses/i2c-bfin-gpio.c
--- /dev/null
+++ a/drivers/i2c/busses/i2c-bfin-gpio.c
@@ -0,0 +1,100 @@
+/****************************************************************
+ * Description: *
+ * *
+ * Maintainer: Meihui Fan <mhfan@xxxxxxxx> *
+ * *
+ * CopyRight (c) 2004 HHTech *
+ * www.hhcn.com, www.hhcn.org *
+ * All rights reserved. *
+ * *
+ * This file is free software; *
+ * you are free to modify and/or redistribute it *
+ * under the terms of the GNU General Public Licence (GPL). *
+ * *
+ ****************************************************************/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
+
+#include <asm/blackfin.h>
+#include <asm/gpio.h>
+
+#define I2C_HW_B_HHBF 0x13
+
+static void hhbf_setsda(void *data, int state)
+{
+ if (state) {
+ gpio_direction_input(CONFIG_I2C_BLACKFIN_GPIO_SDA);
+
+ } else {
+ gpio_direction_output(CONFIG_I2C_BLACKFIN_GPIO_SDA);
+ gpio_set_value(CONFIG_I2C_BLACKFIN_GPIO_SDA, 0);
+ }
+}
+
+static void hhbf_setscl(void *data, int state)
+{
+ gpio_set_value(CONFIG_I2C_BLACKFIN_GPIO_SCL, state);
+}
+
+static int hhbf_getsda(void *data)
+{
+ return (gpio_get_value(CONFIG_I2C_BLACKFIN_GPIO_SDA) != 0);
+}
+
+
+static struct i2c_algo_bit_data bit_hhbf_data = {
+ .setsda = hhbf_setsda,
+ .setscl = hhbf_setscl,
+ .getsda = hhbf_getsda,
+ .udelay = CONFIG_I2C_BLACKFIN_GPIO_CYCLE_DELAY,
+ .timeout = HZ
+};
+
+static struct i2c_adapter hhbf_ops = {
+ .owner = THIS_MODULE,
+ .id = I2C_HW_B_HHBF,
+ .algo_data = &bit_hhbf_data,
+ .name = "Blackfin GPIO based I2C driver",
+};
+
+static int __init i2c_hhbf_init(void)
+{
+
+ if (gpio_request(CONFIG_I2C_BLACKFIN_GPIO_SCL, NULL)) {
+ printk(KERN_ERR "%s: gpio_request GPIO %d failed \n", __func__,
+ CONFIG_I2C_BLACKFIN_GPIO_SCL);
+ return -1;
+ }
+
+ if (gpio_request(CONFIG_I2C_BLACKFIN_GPIO_SDA, NULL)) {
+ printk(KERN_ERR "%s: gpio_request GPIO %d failed \n", __func__,
+ CONFIG_I2C_BLACKFIN_GPIO_SDA);
+ return -1;
+ }
+
+
+ gpio_direction_output(CONFIG_I2C_BLACKFIN_GPIO_SCL);
+ gpio_direction_input(CONFIG_I2C_BLACKFIN_GPIO_SDA);
+ gpio_set_value(CONFIG_I2C_BLACKFIN_GPIO_SCL, 1);
+
+ return i2c_bit_add_bus(&hhbf_ops);
+}
+
+static void __exit i2c_hhbf_exit(void)
+{
+ gpio_free(CONFIG_I2C_BLACKFIN_GPIO_SCL);
+ gpio_free(CONFIG_I2C_BLACKFIN_GPIO_SDA);
+ i2c_bit_del_bus(&hhbf_ops);
+}
+
+MODULE_AUTHOR("Meihui Fan <mhfan@xxxxxxxx>");
+MODULE_DESCRIPTION("I2C-Bus adapter routines for Blackfin and HHBF Boards");
+MODULE_LICENSE("GPL");
+
+module_init(i2c_hhbf_init);
+module_exit(i2c_hhbf_exit);
diff -puN /dev/null drivers/i2c/busses/i2c-bfin-twi.c
--- /dev/null
+++ a/drivers/i2c/busses/i2c-bfin-twi.c
@@ -0,0 +1,589 @@
+/****************************************************************
+ * Description: Driver for Blackfin Two Wire Interface *
+ * Maintainer: sonicz <sonic.zhang@xxxxxxxxxx> *
+ * *
+ * Copyright (c) 2005-2007 Analog Device *
+ * *
+ * This file is free software; *
+ * you are free to modify and/or redistribute it *
+ * under the terms of the GNU General Public Licence (GPL). *
+ ****************************************************************/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/mm.h>
+#include <linux/timer.h>
+#include <linux/spinlock.h>
+#include <linux/completion.h>
+#include <linux/interrupt.h>
+
+#include <asm/blackfin.h>
+#include <asm/irq.h>
+
+#define I2C_BLACKFIN_TWI 0x00
+#define POLL_TIMEOUT (2 * HZ)
+#ifndef CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ
+#define CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ 400
+#endif
+
+/* SMBus mode*/
+#define TWI_I2C_MODE_STANDARD 0x01
+#define TWI_I2C_MODE_STANDARDSUB 0x02
+#define TWI_I2C_MODE_COMBINED 0x04
+
+struct bfin_twi_iface
+{
+ struct mutex twi_lock;
+ int irq;
+ spinlock_t lock;
+ char read_write;
+ u8 command;
+ u8 *transPtr;
+ int readNum;
+ int writeNum;
+ int cur_mode;
+ int manual_stop;
+ int result;
+ int timeout_count;
+ struct timer_list timeout_timer;
+ struct i2c_adapter adap;
+ struct completion complete;
+};
+
+static struct bfin_twi_iface twi_iface;
+
+static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface)
+{
+ unsigned short twi_int_status = bfin_read_TWI_INT_STAT();
+ unsigned short mast_stat = bfin_read_TWI_MASTER_STAT();
+
+ if (twi_int_status & XMTSERV) {
+ /* Transmit next data */
+ if (iface->writeNum > 0) {
+ bfin_write_TWI_XMT_DATA8(*(iface->transPtr++));
+ iface->writeNum--;
+ }
+ /* start receive immediately after complete sending in
+ * combine mode.
+ */
+ else if (iface->cur_mode == TWI_I2C_MODE_COMBINED) {
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL()
+ | MDIR | RSTART);
+ } else if (iface->manual_stop)
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL()
+ | STOP);
+ SSYNC();
+ /* Clear status */
+ bfin_write_TWI_INT_STAT(XMTSERV);
+ SSYNC();
+ }
+ if (twi_int_status & RCVSERV) {
+ if (iface->readNum > 0) {
+ /* Receive next data */
+ *(iface->transPtr) = bfin_read_TWI_RCV_DATA8();
+ if (iface->cur_mode == TWI_I2C_MODE_COMBINED) {
+ /* Change combine mode into sub mode after
+ * read first data.
+ */
+ iface->cur_mode = TWI_I2C_MODE_STANDARDSUB;
+ /* Get read number from first byte in block
+ * combine mode.
+ */
+ if (iface->readNum == 1 && iface->manual_stop)
+ iface->readNum = *iface->transPtr+1;
+ }
+ iface->transPtr++;
+ iface->readNum--;
+ } else if (iface->manual_stop) {
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL()
+ | STOP);
+ SSYNC();
+ }
+ /* Clear interrupt source */
+ bfin_write_TWI_INT_STAT(RCVSERV);
+ SSYNC();
+ }
+ if (twi_int_status & MERR) {
+ bfin_write_TWI_INT_STAT(MERR);
+ bfin_write_TWI_INT_MASK(0);
+ bfin_write_TWI_MASTER_STAT(0x3e);
+ bfin_write_TWI_MASTER_CTL(0);
+ SSYNC();
+ iface->result = -1;
+ /* if both err and complete int stats are set, return proper
+ * results.
+ */
+ if (twi_int_status & MCOMP) {
+ bfin_write_TWI_INT_STAT(MCOMP);
+ bfin_write_TWI_INT_MASK(0);
+ bfin_write_TWI_MASTER_CTL(0);
+ SSYNC();
+ /* If it is a quick transfer, only address bug no data,
+ * not an err, return 1.
+ */
+ if (iface->writeNum == 0 && (mast_stat & BUFRDERR))
+ iface->result = 1;
+ /* If address not acknowledged return -1,
+ * else return 0.
+ */
+ else if (!(mast_stat & ANAK))
+ iface->result = 0;
+ }
+ complete(&iface->complete);
+ return;
+ }
+ if (twi_int_status & MCOMP) {
+ bfin_write_TWI_INT_STAT(MCOMP);
+ SSYNC();
+ if (iface->cur_mode == TWI_I2C_MODE_COMBINED) {
+ if (iface->readNum == 0) {
+ /* set the read number to 1 and ask for manual
+ * stop in block combine mode
+ */
+ iface->readNum = 1;
+ iface->manual_stop = 1;
+ bfin_write_TWI_MASTER_CTL(
+ bfin_read_TWI_MASTER_CTL()
+ | (0xff << 6));
+ } else {
+ /* set the readd number in other
+ * combine mode.
+ */
+ bfin_write_TWI_MASTER_CTL(
+ (bfin_read_TWI_MASTER_CTL() &
+ (~(0xff << 6))) |
+ ( iface->readNum << 6));
+ }
+ /* remove restart bit and enable master receive */
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL() &
+ ~RSTART);
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL() |
+ MEN | MDIR);
+ SSYNC();
+ } else {
+ iface->result = 1;
+ bfin_write_TWI_INT_MASK(0);
+ bfin_write_TWI_MASTER_CTL(0);
+ SSYNC();
+ complete(&iface->complete);
+ }
+ }
+}
+
+/* Interrupt handler */
+static irqreturn_t bfin_twi_interrupt_entry(int irq, void *dev_id)
+{
+ struct bfin_twi_iface *iface = (struct bfin_twi_iface *)dev_id;
+ unsigned long flags;
+
+ spin_lock_irqsave(&iface->lock, flags);
+ del_timer(&iface->timeout_timer);
+ bfin_twi_handle_interrupt(iface);
+ spin_unlock_irqrestore(&iface->lock, flags);
+ return IRQ_HANDLED;
+}
+
+static void bfin_twi_timeout(unsigned long data)
+{
+ struct bfin_twi_iface *iface = (struct bfin_twi_iface *)data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&iface->lock, flags);
+ bfin_twi_handle_interrupt(iface);
+ if (iface->result == 0) {
+ iface->timeout_count--;
+ if (iface->timeout_count > 0) {
+ iface->timeout_timer.expires = jiffies + POLL_TIMEOUT;
+ add_timer(&iface->timeout_timer);
+ } else {
+ iface->result = -1;
+ complete(&iface->complete);
+ }
+ }
+ spin_unlock_irqrestore(&iface->lock, flags);
+}
+
+/*
+ * Generic i2c master transfer entrypoint
+ */
+static int bfin_twi_master_xfer(struct i2c_adapter *adap,
+ struct i2c_msg msgs[], int num)
+{
+ struct bfin_twi_iface* iface = adap->algo_data;
+ struct i2c_msg *pmsg;
+ int i, ret;
+ int rc = 0;
+
+ if (!(bfin_read_TWI_CONTROL() & TWI_ENA))
+ return -ENXIO;
+
+ mutex_lock(&iface->twi_lock);
+
+ while (bfin_read_TWI_MASTER_STAT() & BUSBUSY) {
+ mutex_unlock(&iface->twi_lock);
+ cond_resched();
+ mutex_lock(&iface->twi_lock);
+ }
+
+ ret = 0;
+ for (i = 0; rc >= 0 && i < num; i++) {
+ pmsg = &msgs[i];
+ if (pmsg->flags & I2C_M_TEN) {
+ printk(KERN_ERR "i2c-bfin-twi: 10 bits addr \
+ not supported !\n");
+ rc = -EINVAL;
+ break;
+ }
+
+ iface->cur_mode = TWI_I2C_MODE_STANDARD;
+ iface->manual_stop = 0;
+ iface->transPtr = pmsg->buf;
+ iface->writeNum = iface->readNum = pmsg->len;
+ iface->result = 0;
+ iface->timeout_count = 10;
+ /* Set Transmit device address */
+ bfin_write_TWI_MASTER_ADDR(pmsg->addr);
+
+ /* FIFO Initiation. Data in FIFO should be
+ * discarded before start a new operation.
+ */
+ bfin_write_TWI_FIFO_CTL(0x3);
+ SSYNC();
+ bfin_write_TWI_FIFO_CTL(0);
+ SSYNC();
+
+ if (pmsg->flags & I2C_M_RD)
+ iface->read_write = I2C_SMBUS_READ;
+ else {
+ iface->read_write = I2C_SMBUS_WRITE;
+ /* Transmit first data */
+ if (iface->writeNum > 0) {
+ bfin_write_TWI_XMT_DATA8(*(iface->transPtr++));
+ iface->writeNum--;
+ SSYNC();
+ }
+ }
+
+ /* clear int stat */
+ bfin_write_TWI_INT_STAT(MERR|MCOMP|XMTSERV|RCVSERV);
+
+ /* Interrupt mask . Enable XMT, RCV interrupt */
+ bfin_write_TWI_INT_MASK(MCOMP | MERR |
+ ((iface->read_write == I2C_SMBUS_READ)?
+ RCVSERV : XMTSERV));
+ SSYNC();
+
+ if (pmsg->len > 0 && pmsg->len <= 255)
+ bfin_write_TWI_MASTER_CTL(pmsg->len << 6);
+ else if (pmsg->len > 255) {
+ bfin_write_TWI_MASTER_CTL(0xff << 6);
+ iface->manual_stop = 1;
+ } else
+ break;
+
+ iface->timeout_timer.expires = jiffies + POLL_TIMEOUT;
+ add_timer(&iface->timeout_timer);
+
+ /* Master enable */
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL() | MEN |
+ ((iface->read_write == I2C_SMBUS_READ) ? MDIR : 0) |
+ ((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ>100) ? FAST : 0));
+ SSYNC();
+
+ wait_for_completion(&iface->complete);
+
+ rc = iface->result;
+ if (rc == 1)
+ ret++;
+ else if (rc == -1)
+ break;
+ }
+
+ /* Release mutex */
+ mutex_unlock(&iface->twi_lock);
+
+ return ret;
+}
+
+/*
+ * SMBus type transfer entrypoint
+ */
+
+int bfin_twi_smbus_xfer(struct i2c_adapter *adap, u16 addr,
+ unsigned short flags, char read_write,
+ u8 command, int size, union i2c_smbus_data * data)
+{
+ struct bfin_twi_iface* iface = adap->algo_data;
+ int rc = 0;
+
+ if (!(bfin_read_TWI_CONTROL() & TWI_ENA))
+ return -ENXIO;
+
+ mutex_lock(&iface->twi_lock);
+
+ while(bfin_read_TWI_MASTER_STAT() & BUSBUSY) {
+ mutex_unlock(&iface->twi_lock);
+ cond_resched();
+ mutex_lock(&iface->twi_lock);
+ }
+
+ iface->writeNum = 0;
+ iface->readNum = 0;
+
+ /* Prepare datas & select mode */
+ switch (size) {
+ case I2C_SMBUS_QUICK:
+ iface->transPtr = NULL;
+ iface->cur_mode = TWI_I2C_MODE_STANDARD;
+ break;
+ case I2C_SMBUS_BYTE:
+ if (data == NULL)
+ iface->transPtr = NULL;
+ else {
+ if (read_write == I2C_SMBUS_READ)
+ iface->readNum = 1;
+ else
+ iface->writeNum = 1;
+ iface->transPtr = &data->byte;
+ }
+ iface->cur_mode = TWI_I2C_MODE_STANDARD;
+ break;
+ case I2C_SMBUS_BYTE_DATA:
+ if (read_write == I2C_SMBUS_READ) {
+ iface->readNum = 1;
+ iface->cur_mode = TWI_I2C_MODE_COMBINED;
+ } else {
+ iface->writeNum = 1;
+ iface->cur_mode = TWI_I2C_MODE_STANDARDSUB;
+ }
+ iface->transPtr = &data->byte;
+ break;
+ case I2C_SMBUS_WORD_DATA:
+ if (read_write == I2C_SMBUS_READ) {
+ iface->readNum = 2;
+ iface->cur_mode = TWI_I2C_MODE_COMBINED;
+ } else {
+ iface->writeNum = 2;
+ iface->cur_mode = TWI_I2C_MODE_STANDARDSUB;
+ }
+ iface->transPtr = (u8 *)&data->word;
+ break;
+ case I2C_SMBUS_PROC_CALL:
+ iface->writeNum = 2;
+ iface->readNum = 2;
+ iface->cur_mode = TWI_I2C_MODE_COMBINED;
+ iface->transPtr = (u8 *)&data->word;
+ break;
+ case I2C_SMBUS_BLOCK_DATA:
+ if (read_write == I2C_SMBUS_READ) {
+ iface->readNum = 0;
+ iface->cur_mode = TWI_I2C_MODE_COMBINED;
+ } else {
+ iface->writeNum = data->block[0]+1;
+ iface->cur_mode = TWI_I2C_MODE_STANDARDSUB;
+ }
+ iface->transPtr = data->block;
+ break;
+ default:
+ return -1;
+ }
+
+ iface->result = 0;
+ iface->manual_stop = 0;
+ iface->read_write = read_write;
+ iface->command = command;
+ iface->timeout_count = 10;
+
+ /* FIFO Initiation. Data in FIFO should be discarded before
+ * start a new operation.
+ */
+ bfin_write_TWI_FIFO_CTL(0x3);
+ SSYNC();
+ bfin_write_TWI_FIFO_CTL(0);
+
+ /* clear int stat */
+ bfin_write_TWI_INT_STAT(MERR|MCOMP|XMTSERV|RCVSERV);
+
+ /* Set Transmit device address */
+ bfin_write_TWI_MASTER_ADDR(addr);
+ SSYNC();
+
+ iface->timeout_timer.expires = jiffies + POLL_TIMEOUT;
+ add_timer(&iface->timeout_timer);
+
+ switch (iface->cur_mode) {
+ case TWI_I2C_MODE_STANDARDSUB:
+ bfin_write_TWI_XMT_DATA8(iface->command);
+ bfin_write_TWI_INT_MASK(MCOMP | MERR |
+ ((iface->read_write == I2C_SMBUS_READ) ?
+ RCVSERV : XMTSERV));
+ SSYNC();
+
+ if (iface->writeNum + 1 <= 255)
+ bfin_write_TWI_MASTER_CTL((iface->writeNum+1) << 6);
+ else {
+ bfin_write_TWI_MASTER_CTL(0xff << 6);
+ iface->manual_stop = 1;
+ }
+ /* Master enable */
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL() | MEN |
+ ((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ>100) ? FAST : 0));
+ break;
+ case TWI_I2C_MODE_COMBINED:
+ bfin_write_TWI_XMT_DATA8(iface->command);
+ bfin_write_TWI_INT_MASK(MCOMP | MERR | RCVSERV | XMTSERV);
+ SSYNC();
+
+ if (iface->writeNum > 0)
+ bfin_write_TWI_MASTER_CTL((iface->writeNum+1) << 6);
+ else
+ bfin_write_TWI_MASTER_CTL(0x1 << 6);
+ /* Master enable */
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL() | MEN |
+ ((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ>100) ? FAST : 0));
+ break;
+ default:
+ bfin_write_TWI_MASTER_CTL(0);
+ if (size != I2C_SMBUS_QUICK) {
+ /* Don't access xmit data register when this is a
+ * read operation.
+ */
+ if (iface->read_write != I2C_SMBUS_READ) {
+ if (iface->writeNum > 0) {
+ bfin_write_TWI_XMT_DATA8
+ (*(iface->transPtr++));
+ if (iface->writeNum <= 255)
+ bfin_write_TWI_MASTER_CTL
+ (iface->writeNum << 6);
+ else {
+ bfin_write_TWI_MASTER_CTL
+ (0xff << 6);
+ iface->manual_stop = 1;
+ }
+ iface->writeNum--;
+ } else {
+ bfin_write_TWI_XMT_DATA8
+ (iface->command);
+ bfin_write_TWI_MASTER_CTL(1 << 6);
+ }
+ } else {
+ if (iface->readNum > 0
+ && iface->readNum <= 255)
+ bfin_write_TWI_MASTER_CTL
+ (iface->readNum << 6);
+ else if (iface->readNum > 255) {
+ bfin_write_TWI_MASTER_CTL( 0xff << 6 );
+ iface->manual_stop = 1;
+ } else {
+ del_timer(&iface->timeout_timer);
+ break;
+ }
+ }
+ }
+ bfin_write_TWI_INT_MASK(MCOMP | MERR |
+ ((iface->read_write == I2C_SMBUS_READ) ?
+ RCVSERV : XMTSERV));
+ SSYNC();
+
+ /* Master enable */
+ bfin_write_TWI_MASTER_CTL(bfin_read_TWI_MASTER_CTL() | MEN |
+ ((iface->read_write == I2C_SMBUS_READ) ? MDIR : 0) |
+ ((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ > 100) ? FAST : 0));
+ break;
+ }
+ SSYNC();
+
+ wait_for_completion(&iface->complete);
+
+ rc = (iface->result >= 0) ? 0 : -1;
+
+ /* Release mutex */
+ mutex_unlock(&iface->twi_lock);
+
+ return rc;
+}
+
+/*
+ * Return what the adapter supports
+ */
+static u32 bfin_twi_functionality(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE |
+ I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA |
+ I2C_FUNC_SMBUS_BLOCK_DATA | I2C_FUNC_SMBUS_PROC_CALL |
+ I2C_FUNC_I2C;
+}
+
+
+static struct i2c_algorithm bfin_twi_algorithm = {
+ .master_xfer = bfin_twi_master_xfer,
+ .smbus_xfer = bfin_twi_smbus_xfer,
+ .functionality = bfin_twi_functionality,
+};
+
+static int __init i2c_bfin_twi_init(void)
+{
+ struct i2c_adapter *p_adap;
+ int rc;
+
+ mutex_init(&(twi_iface.twi_lock));
+ spin_lock_init(&twi_iface.lock);
+ init_completion(&twi_iface.complete);
+ twi_iface.irq = IRQ_TWI;
+
+ init_timer(&twi_iface.timeout_timer);
+ twi_iface.timeout_timer.function = bfin_twi_timeout;
+ twi_iface.timeout_timer.data = (unsigned long)&twi_iface;
+
+ p_adap = &twi_iface.adap;
+ p_adap->id = I2C_BLACKFIN_TWI;
+ strcpy(p_adap->name, "i2c-bfin-twi");
+ p_adap->algo = &bfin_twi_algorithm;
+ p_adap->algo_data = &twi_iface;
+ p_adap->client_register = NULL;
+ p_adap->client_unregister = NULL;
+ p_adap->class = I2C_CLASS_ALL;
+
+ rc = request_irq(twi_iface.irq, bfin_twi_interrupt_entry,
+ SA_INTERRUPT, "i2c-bfin-twi", &twi_iface);
+ if (rc) {
+ printk(KERN_ERR "i2c-bfin-twi: can't get IRQ %d !\n",
+ twi_iface.irq);
+ return -ENODEV;
+ }
+
+ /* Set TWI internal clock as 10MHz */
+ bfin_write_TWI_CONTROL(((get_sclk() / 1024 / 1024 + 5) / 10) & 0x7F);
+
+ /* Set Twi interface clock as specified */
+ if (CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ > 400)
+ bfin_write_TWI_CLKDIV((( 5*1024 / 400 ) << 8) |
+ (( 5*1024 / 400 ) & 0xFF));
+ else
+ bfin_write_TWI_CLKDIV((( 5*1024 / CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ ) << 8) |
+ (( 5*1024 / CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ ) & 0xFF));
+
+ /* Enable TWI */
+ bfin_write_TWI_CONTROL(bfin_read_TWI_CONTROL() | TWI_ENA);
+ SSYNC();
+
+ rc = i2c_add_adapter(p_adap);
+ if(rc < 0)
+ free_irq(twi_iface.irq, &twi_iface);
+ return rc;
+}
+
+static void __exit i2c_bfin_twi_exit(void)
+{
+ i2c_del_adapter(&twi_iface.adap);
+ free_irq(twi_iface.irq, &twi_iface);
+}
+
+MODULE_AUTHOR("Sonic Zhang <sonic.zhang@xxxxxxxxxx>");
+MODULE_DESCRIPTION("I2C-Bus adapter routines for Blackfin TWI");
+MODULE_LICENSE("GPL");
+
+module_init(i2c_bfin_twi_init);
+module_exit(i2c_bfin_twi_exit);
_
Patches currently in -mm which might be from bryan.wu@xxxxxxxxxx are
blackfin-Documentation.patch
blackfin-arch.patch
driver_bfin_serial_core.patch
driver_bfin_serial_core-update.patch
blackfin-on-chip-ethernet-mac-controller-driver.patch
blackfin-on-chip-ethernet-mac-controller-driver-update.patch
blackfin-patch-add-blackfin-support-in-smc91x.patch
blackfin-on-chip-rtc-controller-driver.patch
blackfin-blackfin-on-chip-spi-controller-driver.patch
blackfin-blackfin-i2c-driver-update-2.patch
blackfin-blackfin-i2c-driver.patch
blackfin-blackfin-i2c-driver-update.patch
blackfin-blackfin-i2c-driver-fix.patch
blackfin-blackfin-utrace-patch.patch
utrace-nommu-fixup-support-utrace.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
