The quilt patch titled
Subject: kasan: move boot parameters section in documentation
has been removed from the -mm tree. Its filename was
kasan-move-boot-parameters-section-in-documentation.patch
This patch was dropped because it was merged into the mm-stable branch\nof git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
------------------------------------------------------
From: Andrey Konovalov <andreyknvl@xxxxxxxxxx>
Subject: kasan: move boot parameters section in documentation
Move the "Boot parameters" section in KASAN documentation next to the
section that describes KASAN build options.
No content changes.
Link: https://lkml.kernel.org/r/870628e1293b4f44edf7cbcb92374ff9eb7503d7.1652203271.git.andreyknvl@xxxxxxxxxx
Link: https://lkml.kernel.org/r/ec9c923f35e7c5312836c4624a7f317dc1ee2c1c.1652123204.git.andreyknvl@xxxxxxxxxx
Signed-off-by: Andrey Konovalov <andreyknvl@xxxxxxxxxx>
Reviewed-by: Marco Elver <elver@xxxxxxxxxx>
Cc: Alexander Potapenko <glider@xxxxxxxxxx>
Cc: Andrey Ryabinin <ryabinin.a.a@xxxxxxxxx>
Cc: Dmitry Vyukov <dvyukov@xxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
Documentation/dev-tools/kasan.rst | 82 ++++++++++++++--------------
1 file changed, 41 insertions(+), 41 deletions(-)
--- a/Documentation/dev-tools/kasan.rst~kasan-move-boot-parameters-section-in-documentation
+++ a/Documentation/dev-tools/kasan.rst
@@ -94,6 +94,47 @@ To include alloc and free stack traces o
enable ``CONFIG_STACKTRACE``. To include alloc and free stack traces of affected
physical pages, enable ``CONFIG_PAGE_OWNER`` and boot with ``page_owner=on``.
+Boot parameters
+~~~~~~~~~~~~~~~
+
+KASAN is affected by the generic ``panic_on_warn`` command line parameter.
+When it is enabled, KASAN panics the kernel after printing a bug report.
+
+By default, KASAN prints a bug report only for the first invalid memory access.
+With ``kasan_multi_shot``, KASAN prints a report on every invalid access. This
+effectively disables ``panic_on_warn`` for KASAN reports.
+
+Alternatively, independent of ``panic_on_warn``, the ``kasan.fault=`` boot
+parameter can be used to control panic and reporting behaviour:
+
+- ``kasan.fault=report`` or ``=panic`` controls whether to only print a KASAN
+ report or also panic the kernel (default: ``report``). The panic happens even
+ if ``kasan_multi_shot`` is enabled.
+
+Hardware Tag-Based KASAN mode (see the section about various modes below) is
+intended for use in production as a security mitigation. Therefore, it supports
+additional boot parameters that allow disabling KASAN or controlling features:
+
+- ``kasan=off`` or ``=on`` controls whether KASAN is enabled (default: ``on``).
+
+- ``kasan.mode=sync``, ``=async`` or ``=asymm`` controls whether KASAN
+ is configured in synchronous, asynchronous or asymmetric mode of
+ execution (default: ``sync``).
+ Synchronous mode: a bad access is detected immediately when a tag
+ check fault occurs.
+ Asynchronous mode: a bad access detection is delayed. When a tag check
+ fault occurs, the information is stored in hardware (in the TFSR_EL1
+ register for arm64). The kernel periodically checks the hardware and
+ only reports tag faults during these checks.
+ Asymmetric mode: a bad access is detected synchronously on reads and
+ asynchronously on writes.
+
+- ``kasan.vmalloc=off`` or ``=on`` disables or enables tagging of vmalloc
+ allocations (default: ``on``).
+
+- ``kasan.stacktrace=off`` or ``=on`` disables or enables alloc and free stack
+ traces collection (default: ``on``).
+
Error reports
~~~~~~~~~~~~~
@@ -208,47 +249,6 @@ traces point to places in code that inte
directly present in the bad access stack trace. Currently, this includes
call_rcu() and workqueue queuing.
-Boot parameters
-~~~~~~~~~~~~~~~
-
-KASAN is affected by the generic ``panic_on_warn`` command line parameter.
-When it is enabled, KASAN panics the kernel after printing a bug report.
-
-By default, KASAN prints a bug report only for the first invalid memory access.
-With ``kasan_multi_shot``, KASAN prints a report on every invalid access. This
-effectively disables ``panic_on_warn`` for KASAN reports.
-
-Alternatively, independent of ``panic_on_warn``, the ``kasan.fault=`` boot
-parameter can be used to control panic and reporting behaviour:
-
-- ``kasan.fault=report`` or ``=panic`` controls whether to only print a KASAN
- report or also panic the kernel (default: ``report``). The panic happens even
- if ``kasan_multi_shot`` is enabled.
-
-Hardware Tag-Based KASAN mode (see the section about various modes below) is
-intended for use in production as a security mitigation. Therefore, it supports
-additional boot parameters that allow disabling KASAN or controlling features:
-
-- ``kasan=off`` or ``=on`` controls whether KASAN is enabled (default: ``on``).
-
-- ``kasan.mode=sync``, ``=async`` or ``=asymm`` controls whether KASAN
- is configured in synchronous, asynchronous or asymmetric mode of
- execution (default: ``sync``).
- Synchronous mode: a bad access is detected immediately when a tag
- check fault occurs.
- Asynchronous mode: a bad access detection is delayed. When a tag check
- fault occurs, the information is stored in hardware (in the TFSR_EL1
- register for arm64). The kernel periodically checks the hardware and
- only reports tag faults during these checks.
- Asymmetric mode: a bad access is detected synchronously on reads and
- asynchronously on writes.
-
-- ``kasan.vmalloc=off`` or ``=on`` disables or enables tagging of vmalloc
- allocations (default: ``on``).
-
-- ``kasan.stacktrace=off`` or ``=on`` disables or enables alloc and free stack
- traces collection (default: ``on``).
-
Implementation details
----------------------
_
Patches currently in -mm which might be from andreyknvl@xxxxxxxxxx are
