The patch titled
PATA libata: suspend/resume simple cases
has been added to the -mm tree. Its filename is
pata-libata-suspend-resume-simple-cases.patch
See http://www.zip.com.au/~akpm/linux/patches/stuff/added-to-mm.txt to find
out what to do about this
------------------------------------------------------
Subject: PATA libata: suspend/resume simple cases
From: Alan Cox <alan@xxxxxxxxxxxxxxxxxxx>
Add the suspend/resume callbacks for drivers which don't need any additional
help (beyond the pci resume quirk patch I posted earlier anyway). Also bring
version numbers back inline with master copies.
Signed-off-by: Alan Cox <alan@xxxxxxxxxx>
Cc: Jeff Garzik <jeff@xxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxx>
---
drivers/ata/ata_generic.c | 8 ++++++--
drivers/ata/pata_atiixp.c | 8 ++++++--
drivers/ata/pata_cs5535.c | 6 +++++-
drivers/ata/pata_cypress.c | 8 ++++++--
drivers/ata/pata_efar.c | 6 +++++-
drivers/ata/pata_marvell.c | 6 +++++-
drivers/ata/pata_mpiix.c | 8 ++++++--
drivers/ata/pata_netcell.c | 6 +++++-
drivers/ata/pata_ns87410.c | 8 ++++++--
drivers/ata/pata_oldpiix.c | 4 ++++
drivers/ata/pata_opti.c | 33 ++++++---------------------------
drivers/ata/pata_optidma.c | 8 ++++++--
drivers/ata/pata_radisys.c | 4 ++++
drivers/ata/pata_sc1200.c | 8 ++++++--
drivers/ata/pata_triflex.c | 8 ++++++--
15 files changed, 82 insertions(+), 47 deletions(-)
diff -puN drivers/ata/ata_generic.c~pata-libata-suspend-resume-simple-cases drivers/ata/ata_generic.c
--- a/drivers/ata/ata_generic.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/ata_generic.c
@@ -26,7 +26,7 @@
#include <linux/libata.h>
#define DRV_NAME "ata_generic"
-#define DRV_VERSION "0.2.7"
+#define DRV_VERSION "0.2.10"
/*
* A generic parallel ATA driver using libata
@@ -117,6 +117,8 @@ static struct scsi_host_template generic
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations generic_port_ops = {
@@ -225,7 +227,9 @@ static struct pci_driver ata_generic_pci
.name = DRV_NAME,
.id_table = ata_generic,
.probe = ata_generic_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init ata_generic_init(void)
diff -puN drivers/ata/pata_atiixp.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_atiixp.c
--- a/drivers/ata/pata_atiixp.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_atiixp.c
@@ -22,7 +22,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_atiixp"
-#define DRV_VERSION "0.4.3"
+#define DRV_VERSION "0.4.4"
enum {
ATIIXP_IDE_PIO_TIMING = 0x40,
@@ -217,6 +217,8 @@ static struct scsi_host_template atiixp_
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations atiixp_port_ops = {
@@ -280,7 +282,9 @@ static struct pci_driver atiixp_pci_driv
.name = DRV_NAME,
.id_table = atiixp,
.probe = atiixp_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .resume = ata_pci_device_resume,
+ .suspend = ata_pci_device_suspend,
};
static int __init atiixp_init(void)
diff -puN drivers/ata/pata_cs5535.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_cs5535.c
--- a/drivers/ata/pata_cs5535.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_cs5535.c
@@ -39,7 +39,7 @@
#include <asm/msr.h>
#define DRV_NAME "cs5535"
-#define DRV_VERSION "0.2.10"
+#define DRV_VERSION "0.2.11"
/*
* The Geode (Aka Athlon GX now) uses an internal MSR based
@@ -185,6 +185,8 @@ static struct scsi_host_template cs5535_
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations cs5535_port_ops = {
@@ -268,6 +270,8 @@ static struct pci_driver cs5535_pci_driv
.id_table = cs5535,
.probe = cs5535_init_one,
.remove = ata_pci_remove_one
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init cs5535_init(void)
diff -puN drivers/ata/pata_cypress.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_cypress.c
--- a/drivers/ata/pata_cypress.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_cypress.c
@@ -18,7 +18,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_cypress"
-#define DRV_VERSION "0.1.2"
+#define DRV_VERSION "0.1.4"
/* here are the offset definitions for the registers */
@@ -136,6 +136,8 @@ static struct scsi_host_template cy82c69
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations cy82c693_port_ops = {
@@ -203,7 +205,9 @@ static struct pci_driver cy82c693_pci_dr
.name = DRV_NAME,
.id_table = cy82c693,
.probe = cy82c693_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init cy82c693_init(void)
diff -puN drivers/ata/pata_efar.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_efar.c
--- a/drivers/ata/pata_efar.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_efar.c
@@ -22,7 +22,7 @@
#include <linux/ata.h>
#define DRV_NAME "pata_efar"
-#define DRV_VERSION "0.4.2"
+#define DRV_VERSION "0.4.3"
/**
* efar_pre_reset - check for 40/80 pin
@@ -234,6 +234,8 @@ static struct scsi_host_template efar_sh
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations efar_ops = {
@@ -315,6 +317,8 @@ static struct pci_driver efar_pci_driver
.id_table = efar_pci_tbl,
.probe = efar_init_one,
.remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init efar_init(void)
diff -puN drivers/ata/pata_marvell.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_marvell.c
--- a/drivers/ata/pata_marvell.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_marvell.c
@@ -20,7 +20,7 @@
#include <linux/ata.h>
#define DRV_NAME "pata_marvell"
-#define DRV_VERSION "0.0.5u"
+#define DRV_VERSION "0.1.1"
/**
* marvell_pre_reset - check for 40/80 pin
@@ -103,6 +103,8 @@ static struct scsi_host_template marvell
.slave_configure = ata_scsi_slave_config,
/* Use standard CHS mapping rules */
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations marvell_ops = {
@@ -197,6 +199,8 @@ static struct pci_driver marvell_pci_dri
.id_table = marvell_pci_tbl,
.probe = marvell_init_one,
.remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init marvell_init(void)
diff -puN drivers/ata/pata_mpiix.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_mpiix.c
--- a/drivers/ata/pata_mpiix.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_mpiix.c
@@ -35,7 +35,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_mpiix"
-#define DRV_VERSION "0.7.2"
+#define DRV_VERSION "0.7.3"
enum {
IDETIM = 0x6C, /* IDE control register */
@@ -167,6 +167,8 @@ static struct scsi_host_template mpiix_s
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations mpiix_port_ops = {
@@ -284,7 +286,9 @@ static struct pci_driver mpiix_pci_drive
.name = DRV_NAME,
.id_table = mpiix,
.probe = mpiix_init_one,
- .remove = mpiix_remove_one
+ .remove = mpiix_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init mpiix_init(void)
diff -puN drivers/ata/pata_netcell.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_netcell.c
--- a/drivers/ata/pata_netcell.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_netcell.c
@@ -16,7 +16,7 @@
#include <linux/ata.h>
#define DRV_NAME "pata_netcell"
-#define DRV_VERSION "0.1.5"
+#define DRV_VERSION "0.1.6"
/**
* netcell_probe_init - check for 40/80 pin
@@ -64,6 +64,8 @@ static struct scsi_host_template netcell
.slave_configure = ata_scsi_slave_config,
/* Use standard CHS mapping rules */
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations netcell_ops = {
@@ -152,6 +154,8 @@ static struct pci_driver netcell_pci_dri
.id_table = netcell_pci_tbl,
.probe = netcell_init_one,
.remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init netcell_init(void)
diff -puN drivers/ata/pata_ns87410.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_ns87410.c
--- a/drivers/ata/pata_ns87410.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_ns87410.c
@@ -28,7 +28,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_ns87410"
-#define DRV_VERSION "0.4.2"
+#define DRV_VERSION "0.4.3"
/**
* ns87410_pre_reset - probe begin
@@ -157,6 +157,8 @@ static struct scsi_host_template ns87410
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations ns87410_port_ops = {
@@ -209,7 +211,9 @@ static struct pci_driver ns87410_pci_dri
.name = DRV_NAME,
.id_table = ns87410,
.probe = ns87410_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init ns87410_init(void)
diff -puN drivers/ata/pata_oldpiix.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_oldpiix.c
--- a/drivers/ata/pata_oldpiix.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_oldpiix.c
@@ -232,6 +232,8 @@ static struct scsi_host_template oldpiix
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations oldpiix_pata_ops = {
@@ -313,6 +315,8 @@ static struct pci_driver oldpiix_pci_dri
.id_table = oldpiix_pci_tbl,
.probe = oldpiix_init_one,
.remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init oldpiix_init(void)
diff -puN drivers/ata/pata_opti.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_opti.c
--- a/drivers/ata/pata_opti.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_opti.c
@@ -34,7 +34,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_opti"
-#define DRV_VERSION "0.2.5"
+#define DRV_VERSION "0.2.7"
enum {
READ_REG = 0, /* index of Read cycle timing register */
@@ -109,30 +109,6 @@ static void opti_write_reg(struct ata_po
outb(0x83, regio + 2);
}
-#if 0
-/**
- * opti_read_reg - control register read
- * @ap: ATA port
- * @reg: control register number
- *
- * The Opti uses magic 'trapdoor' register accesses to do configuration
- * rather than using PCI space as other controllers do. The double inw
- * on the error register activates configuration mode. We can then read
- * the control register
- */
-
-static u8 opti_read_reg(struct ata_port *ap, int reg)
-{
- unsigned long regio = ap->ioaddr.cmd_addr;
- u8 ret;
- inw(regio + 1);
- inw(regio + 1);
- outb(3, regio + 2);
- ret = inb(regio + reg);
- outb(0x83, regio + 2);
-}
-#endif
-
/**
* opti_set_piomode - set initial PIO mode data
* @ap: ATA interface
@@ -203,12 +179,13 @@ static struct scsi_host_template opti_sh
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations opti_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = opti_set_piomode,
-/* .set_dmamode = opti_set_dmamode, */
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
@@ -266,7 +243,9 @@ static struct pci_driver opti_pci_driver
.name = DRV_NAME,
.id_table = opti,
.probe = opti_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init opti_init(void)
diff -puN drivers/ata/pata_optidma.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_optidma.c
--- a/drivers/ata/pata_optidma.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_optidma.c
@@ -33,7 +33,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_optidma"
-#define DRV_VERSION "0.2.2"
+#define DRV_VERSION "0.2.3"
enum {
READ_REG = 0, /* index of Read cycle timing register */
@@ -360,6 +360,8 @@ static struct scsi_host_template optidma
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations optidma_port_ops = {
@@ -521,7 +523,9 @@ static struct pci_driver optidma_pci_dri
.name = DRV_NAME,
.id_table = optidma,
.probe = optidma_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init optidma_init(void)
diff -puN drivers/ata/pata_radisys.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_radisys.c
--- a/drivers/ata/pata_radisys.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_radisys.c
@@ -228,6 +228,8 @@ static struct scsi_host_template radisys
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations radisys_pata_ops = {
@@ -310,6 +312,8 @@ static struct pci_driver radisys_pci_dri
.id_table = radisys_pci_tbl,
.probe = radisys_init_one,
.remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init radisys_init(void)
diff -puN drivers/ata/pata_sc1200.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_sc1200.c
--- a/drivers/ata/pata_sc1200.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_sc1200.c
@@ -40,7 +40,7 @@
#include <linux/libata.h>
#define DRV_NAME "sc1200"
-#define DRV_VERSION "0.2.3"
+#define DRV_VERSION "0.2.4"
#define SC1200_REV_A 0x00
#define SC1200_REV_B1 0x01
@@ -194,6 +194,8 @@ static struct scsi_host_template sc1200_
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations sc1200_port_ops = {
@@ -263,7 +265,9 @@ static struct pci_driver sc1200_pci_driv
.name = DRV_NAME,
.id_table = sc1200,
.probe = sc1200_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init sc1200_init(void)
diff -puN drivers/ata/pata_triflex.c~pata-libata-suspend-resume-simple-cases drivers/ata/pata_triflex.c
--- a/drivers/ata/pata_triflex.c~pata-libata-suspend-resume-simple-cases
+++ a/drivers/ata/pata_triflex.c
@@ -43,7 +43,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_triflex"
-#define DRV_VERSION "0.2.5"
+#define DRV_VERSION "0.2.7"
/**
* triflex_prereset - probe begin
@@ -193,6 +193,8 @@ static struct scsi_host_template triflex
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations triflex_port_ops = {
@@ -257,7 +259,9 @@ static struct pci_driver triflex_pci_dri
.name = DRV_NAME,
.id_table = triflex,
.probe = triflex_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static int __init triflex_init(void)
_
Patches currently in -mm which might be from alan@xxxxxxxxxxxxxxxxxxx are
git-libata-all.patch
pata-libata-suspend-resume-simple-cases.patch
pata_cmd64x-suspend-resume.patch
pata_cs5520-resume-support.patch
pata_jmicron-fix-jmb368-support-add-suspend-resume.patch
pata_cs5530-suspend-resume-support.patch
pata_rz1000-force-readahead-off-on-resume.patch
pata_ali-suspend-resume-support.patch
pata_sil680-suspend-resume.patch
via-pata-controller-xfer-fixes.patch
via-pata-controller-xfer-fixes-fix.patch
ahci-ati-sb600-sata-support-for-various-modes.patch
git-mtd.patch
resend-iphase-64bit-cleanup.patch
make-sure-uart-is-powered-up-when-dumping-mctrl-status.patch
perle-multimodem-card-pci-ras-detection.patch
pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
pci-fix-multiple-problems-with-via-hardware.patch
drivers-scsi-ncr5380c-replacing-yield-with-a.patch
drivers-scsi-mca_53c9xc-save_flags-cli-removal.patch
alpha-switch-to-pci_get-api.patch
edac-new-opteron-athlon64-memory-controller-driver.patch
serial-uartlite-driver.patch
serial-uartlite-driver-fix.patch
fix-serial-uartlite-after-global-pt_regs.patch
serial-uartlite-support-multiple-devices.patch
serial-uartlite-initialize-port-parameters-in-console_setup.patch
honour-mnt_noexec-for-access.patch
i2o-more-error-checking.patch
ide-complete-switch-to-pci_get.patch
via82cxxx-handle-error-condition-properly.patch
lockdep-fix-ide-proc-interaction.patch
exar-quad-port-serial.patch
exar-quad-port-serial-fix.patch
hz-300hz-support.patch
do_task_stat-dont-take-tty_mutex.patch
mxser-correct-tty-driver-name.patch
pci-mxser-pci-refcounts.patch
mxser-make-an-experimental-clone.patch
char-mxser_new-correct-include-file.patch
char-mxser_new-upgrade-to-191.patch
char-mxser_new-rework-to-allow-dynamic-structs.patch
char-mxser_new-eliminate-tty-ldisc-deref.patch
char-mxser_new-testbit-for-bit-testing.patch
char-mxser_new-correct-fail-paths.patch
char-mxser_new-dont-check-tty_unregister-retval.patch
char-mxser_new-compress-isa-finding.patch
char-mxser_new-register-tty-devices-on-the-fly.patch
char-mxser_new-compact-structures-round2.patch
char-mxser_new-reverse-if-else-paths-patch.patch
char-mxser_new-comments-cleanup.patch
char-mxser_new-correct-intr-handler-proto.patch
char-mxser_new-delete-ttys-and-termios.patch
char-mxser_new-pci-probing.patch
mxser_new-correct-tty-driver-name.patch
char-stallion-use-pr_debug-macro.patch
char-stallion-remove-unneeded-casts.patch
char-stallion-kill-typedefs.patch
char-stallion-move-init-deinit.patch
char-stallion-uninline-functions.patch
char-stallion-mark-functions-as-init.patch
char-stallion-remove-many-prototypes.patch
tty-preparatory-structures-for-termios-revamp.patch
tty-preparatory-structures-for-termios-revamp-strip-fix.patch
tty-switch-to-ktermios-and-new-framework.patch
tty-switch-to-ktermios.patch
tty-switch-to-ktermios-nozomi-fix.patch
tty-switch-to-ktermios-bluetooth-fix.patch
tty-switch-to-ktermios-3270-fix.patch
tty-switch-to-ktermios-uml-fix.patch
tty_ioctl-use-termios-for-the-old-structure-and-termios2.patch
tty_ioctl-use-termios-for-the-old-structure-and-termios2-update.patch
termios-enable-new-style-termios-ioctls-on-x86-64.patch
char-isicom-use-completion.patch
char-isicom-simplify-timer.patch
char-isicom-remove-cvs-stuff.patch
char-isicom-fix-tty-index-check.patch
char-sx-convert-to-pci-probing.patch
char-sx-use-kcalloc.patch
char-sx-mark-functions-as-devinit.patch
char-sx-use-eisa-probing.patch
char-sx-ifdef-isa-code.patch
char-sx-lock-boards-struct.patch
char-sx-remove-duplicite-code.patch
char-sx-whitespace-cleanup.patch
char-sx-simplify-timer-logic.patch
char-sx-fix-return-in-module-init.patch
char-sx-use-pci_iomap.patch
char-sx-request-regions.patch
char-stallion-convert-to-pci-probing.patch
char-stallion-prints-cleanup.patch
char-stallion-implement-fail-paths.patch
char-stallion-correct-__init-macros.patch
char-stallion-functions-cleanup.patch
char-stallion-fix-fail-paths.patch
char-stallion-brd-struct-locking.patch
char-stallion-remove-syntactic-sugar.patch
char-stallion-variables-cleanup.patch
char-stallion-use-dynamic-dev.patch
char-istallion-convert-to-pci-probing.patch
char-istallion-remove-the-mess.patch
char-istallion-eliminate-typedefs.patch
char-istallion-variables-cleanup.patch
char-istallion-ifdef-eisa-code.patch
char-istallion-brdnr-locking.patch
char-istallion-free-only-isa.patch
char-istallion-correct-fail-paths.patch
char-istallion-correct-fail-paths-fix.patch
char-istallion-fix-enabling.patch
char-istallion-move-init-and-exit-code.patch
char-istallion-change-init-sequence.patch
char-istallion-dynamic-tty-device.patch
char-istallion-use-mod_timer.patch
char-cyclades-save-indent-levels.patch
char-cyclades-lindent-the-code.patch
char-cyclades-cleanup.patch
char-cyclades-fix-warnings.patch
ide-hpt3xxn-clocking-fixes.patch
ide-fix-hpt37x-timing-tables.patch
ide-optimize-hpt37x-timing-tables.patch
ide-fix-hpt3xx-hotswap-support.patch
ide-fix-the-case-of-multiple-hpt3xx-chips-present.patch
ide-hpt3xx-fix-pci-clock-detection.patch
ide-hpt3xx-fix-pci-clock-detection-fix-2.patch
piix-fix-82371mx-enablebits.patch
piix-remove-check-for-broken-mw-dma-mode-0.patch
piix-slc90e66-pio-mode-fallback-fix.patch
hpt3xx-rework-rate-filtering.patch
hpt3xx-rework-rate-filtering-tidy.patch
hpt3xx-print-the-real-chip-name-at-startup.patch
hpt3xx-switch-to-using-pci_get_slot.patch
hpt3xx-cache-channels-mcr-address.patch
hpt3x7-merge-speedproc-handlers.patch
hpt370-clean-up-dma-timeout-handling.patch
hpt3xx-init-code-rewrite.patch
ide-more-conversion-to-pci_get-apis.patch
igafb-switch-to-pci_get-api.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
