The patch titled
Subject: mm/sparse: cleanup the code surrounding memory_present()
has been removed from the -mm tree. Its filename was
mm-sparse-cleanup-the-code-surrounding-memory_present.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
From: Mike Rapoport <rppt@xxxxxxxxxxxxx>
Subject: mm/sparse: cleanup the code surrounding memory_present()
After removal of CONFIG_HAVE_MEMBLOCK_NODE_MAP we have two equivalent
functions that call memory_present() for each region in memblock.memory:
sparse_memory_present_with_active_regions() and membocks_present().
Moreover, all architectures have a call to either of these functions
preceding the call to sparse_init() and in the most cases they are called
one after the other.
Mark the regions from memblock.memory as present during sparce_init() by
making sparse_init() call memblocks_present(), make memblocks_present()
and memory_present() functions static and remove redundant
sparse_memory_present_with_active_regions() function.
Also remove no longer required HAVE_MEMORY_PRESENT configuration option.
Link: http://lkml.kernel.org/r/20200712083130.22919-1-rppt@xxxxxxxxxx
Signed-off-by: Mike Rapoport <rppt@xxxxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
Documentation/vm/memory-model.rst | 7 ++-----
arch/arm/mm/init.c | 9 ++-------
arch/arm64/mm/init.c | 6 ++----
arch/ia64/mm/discontig.c | 1 -
arch/microblaze/mm/init.c | 3 ---
arch/mips/kernel/setup.c | 8 --------
arch/mips/loongson64/numa.c | 1 -
arch/mips/sgi-ip27/ip27-memory.c | 2 --
arch/parisc/mm/init.c | 5 -----
arch/powerpc/mm/mem.c | 2 --
arch/powerpc/mm/numa.c | 1 -
arch/riscv/mm/init.c | 1 -
arch/s390/mm/init.c | 1 -
arch/sh/mm/init.c | 6 ------
arch/sh/mm/numa.c | 3 ---
arch/sparc/mm/init_64.c | 1 -
arch/x86/mm/init_32.c | 2 --
arch/x86/mm/init_64.c | 1 -
include/linux/mm.h | 4 ----
include/linux/mmzone.h | 14 --------------
mm/Kconfig | 6 +-----
mm/page_alloc.c | 16 ----------------
mm/sparse.c | 20 ++++++++++++--------
23 files changed, 19 insertions(+), 101 deletions(-)
--- a/arch/arm64/mm/init.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/arm64/mm/init.c
@@ -430,11 +430,9 @@ void __init bootmem_init(void)
#endif
/*
- * Sparsemem tries to allocate bootmem in memory_present(), so must be
- * done after the fixed reservations.
+ * sparse_init() tries to allocate memory from memblock, so must be
+ * done after the fixed reservations
*/
- memblocks_present();
-
sparse_init();
zone_sizes_init(min, max);
--- a/arch/arm/mm/init.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/arm/mm/init.c
@@ -243,13 +243,8 @@ void __init bootmem_init(void)
(phys_addr_t)max_low_pfn << PAGE_SHIFT);
/*
- * Sparsemem tries to allocate bootmem in memory_present(),
- * so must be done after the fixed reservations
- */
- memblocks_present();
-
- /*
- * sparse_init() needs the bootmem allocator up and running.
+ * sparse_init() tries to allocate memory from memblock, so must be
+ * done after the fixed reservations
*/
sparse_init();
--- a/arch/ia64/mm/discontig.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/ia64/mm/discontig.c
@@ -600,7 +600,6 @@ void __init paging_init(void)
max_dma = virt_to_phys((void *) MAX_DMA_ADDRESS) >> PAGE_SHIFT;
- sparse_memory_present_with_active_regions(MAX_NUMNODES);
sparse_init();
#ifdef CONFIG_VIRTUAL_MEM_MAP
--- a/arch/microblaze/mm/init.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/microblaze/mm/init.c
@@ -172,9 +172,6 @@ void __init setup_memory(void)
&memblock.memory, 0);
}
- /* XXX need to clip this if using highmem? */
- sparse_memory_present_with_active_regions(0);
-
paging_init();
}
--- a/arch/mips/kernel/setup.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/mips/kernel/setup.c
@@ -371,14 +371,6 @@ static void __init bootmem_init(void)
#endif
}
-
- /*
- * In any case the added to the memblock memory regions
- * (highmem/lowmem, available/reserved, etc) are considered
- * as present, so inform sparsemem about them.
- */
- memblocks_present();
-
/*
* Reserve initrd memory if needed.
*/
--- a/arch/mips/loongson64/numa.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/mips/loongson64/numa.c
@@ -220,7 +220,6 @@ static __init void prom_meminit(void)
cpumask_clear(&__node_cpumask[node]);
}
}
- memblocks_present();
max_low_pfn = PHYS_PFN(memblock_end_of_DRAM());
for (cpu = 0; cpu < loongson_sysconf.nr_cpus; cpu++) {
--- a/arch/mips/sgi-ip27/ip27-memory.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/mips/sgi-ip27/ip27-memory.c
@@ -402,8 +402,6 @@ void __init prom_meminit(void)
}
__node_data[node] = &null_node;
}
-
- memblocks_present();
}
void __init prom_free_prom_memory(void)
--- a/arch/parisc/mm/init.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/parisc/mm/init.c
@@ -689,11 +689,6 @@ void __init paging_init(void)
flush_cache_all_local(); /* start with known state */
flush_tlb_all_local(NULL);
- /*
- * Mark all memblocks as present for sparsemem using
- * memory_present() and then initialize sparsemem.
- */
- memblocks_present();
sparse_init();
parisc_bootmem_free();
}
--- a/arch/powerpc/mm/mem.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/powerpc/mm/mem.c
@@ -183,8 +183,6 @@ void __init mem_topology_setup(void)
void __init initmem_init(void)
{
- /* XXX need to clip this if using highmem? */
- sparse_memory_present_with_active_regions(0);
sparse_init();
}
--- a/arch/powerpc/mm/numa.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/powerpc/mm/numa.c
@@ -949,7 +949,6 @@ void __init initmem_init(void)
get_pfn_range_for_nid(nid, &start_pfn, &end_pfn);
setup_node_data(nid, start_pfn, end_pfn);
- sparse_memory_present_with_active_regions(nid);
}
sparse_init();
--- a/arch/riscv/mm/init.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/riscv/mm/init.c
@@ -544,7 +544,6 @@ void mark_rodata_ro(void)
void __init paging_init(void)
{
setup_vm_final();
- memblocks_present();
sparse_init();
setup_zero_page();
zone_sizes_init();
--- a/arch/s390/mm/init.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/s390/mm/init.c
@@ -115,7 +115,6 @@ void __init paging_init(void)
__load_psw_mask(psw.mask);
kasan_free_early_identity();
- sparse_memory_present_with_active_regions(MAX_NUMNODES);
sparse_init();
zone_dma_bits = 31;
memset(max_zone_pfns, 0, sizeof(max_zone_pfns));
--- a/arch/sh/mm/init.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/sh/mm/init.c
@@ -241,12 +241,6 @@ static void __init do_init_bootmem(void)
plat_mem_setup();
- for_each_memblock(memory, reg) {
- int nid = memblock_get_region_node(reg);
-
- memory_present(nid, memblock_region_memory_base_pfn(reg),
- memblock_region_memory_end_pfn(reg));
- }
sparse_init();
}
--- a/arch/sh/mm/numa.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/sh/mm/numa.c
@@ -53,7 +53,4 @@ void __init setup_bootmem_node(int nid,
/* It's up */
node_set_online(nid);
-
- /* Kick sparsemem */
- sparse_memory_present_with_active_regions(nid);
}
--- a/arch/sparc/mm/init_64.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/sparc/mm/init_64.c
@@ -1610,7 +1610,6 @@ static unsigned long __init bootmem_init
/* XXX cpu notifier XXX */
- sparse_memory_present_with_active_regions(MAX_NUMNODES);
sparse_init();
return end_pfn;
--- a/arch/x86/mm/init_32.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/x86/mm/init_32.c
@@ -678,7 +678,6 @@ void __init initmem_init(void)
#endif
memblock_set_node(0, PHYS_ADDR_MAX, &memblock.memory, 0);
- sparse_memory_present_with_active_regions(0);
#ifdef CONFIG_FLATMEM
max_mapnr = IS_ENABLED(CONFIG_HIGHMEM) ? highend_pfn : max_low_pfn;
@@ -718,7 +717,6 @@ void __init paging_init(void)
* NOTE: at this point the bootmem allocator is fully available.
*/
olpc_dt_build_devicetree();
- sparse_memory_present_with_active_regions(MAX_NUMNODES);
sparse_init();
zone_sizes_init();
}
--- a/arch/x86/mm/init_64.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/arch/x86/mm/init_64.c
@@ -817,7 +817,6 @@ void __init initmem_init(void)
void __init paging_init(void)
{
- sparse_memory_present_with_active_regions(MAX_NUMNODES);
sparse_init();
/*
--- a/Documentation/vm/memory-model.rst~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/Documentation/vm/memory-model.rst
@@ -141,11 +141,8 @@ sections:
`mem_section` objects and the number of rows is calculated to fit
all the memory sections.
-The architecture setup code should call :c:func:`memory_present` for
-each active memory range or use :c:func:`memblocks_present` or
-:c:func:`sparse_memory_present_with_active_regions` wrappers to
-initialize the memory sections. Next, the actual memory maps should be
-set up using :c:func:`sparse_init`.
+The architecture setup code should call sparse_init() to
+initialize the memory sections and the memory maps.
With SPARSEMEM there are two possible ways to convert a PFN to the
corresponding `struct page` - a "classic sparse" and "sparse
--- a/include/linux/mm.h~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/include/linux/mm.h
@@ -2382,9 +2382,6 @@ static inline unsigned long get_num_phys
* for_each_valid_physical_page_range()
* memblock_add_node(base, size, nid)
* free_area_init(max_zone_pfns);
- *
- * sparse_memory_present_with_active_regions() calls memory_present() for
- * each range when SPARSEMEM is enabled.
*/
void free_area_init(unsigned long *max_zone_pfn);
unsigned long node_map_pfn_alignment(void);
@@ -2395,7 +2392,6 @@ extern unsigned long absent_pages_in_ran
extern void get_pfn_range_for_nid(unsigned int nid,
unsigned long *start_pfn, unsigned long *end_pfn);
extern unsigned long find_min_pfn_with_active_regions(void);
-extern void sparse_memory_present_with_active_regions(int nid);
#ifndef CONFIG_NEED_MULTIPLE_NODES
static inline int early_pfn_to_nid(unsigned long pfn)
--- a/include/linux/mmzone.h~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/include/linux/mmzone.h
@@ -839,18 +839,6 @@ static inline struct pglist_data *lruvec
extern unsigned long lruvec_lru_size(struct lruvec *lruvec, enum lru_list lru, int zone_idx);
-#ifdef CONFIG_HAVE_MEMORY_PRESENT
-void memory_present(int nid, unsigned long start, unsigned long end);
-#else
-static inline void memory_present(int nid, unsigned long start, unsigned long end) {}
-#endif
-
-#if defined(CONFIG_SPARSEMEM)
-void memblocks_present(void);
-#else
-static inline void memblocks_present(void) {}
-#endif
-
#ifdef CONFIG_HAVE_MEMORYLESS_NODES
int local_memory_node(int node_id);
#else
@@ -1407,8 +1395,6 @@ struct mminit_pfnnid_cache {
#define early_pfn_valid(pfn) (1)
#endif
-void memory_present(int nid, unsigned long start, unsigned long end);
-
/*
* If it is possible to have holes within a MAX_ORDER_NR_PAGES, then we
* need to check pfn validity within that MAX_ORDER_NR_PAGES block.
--- a/mm/Kconfig~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/mm/Kconfig
@@ -88,13 +88,9 @@ config NEED_MULTIPLE_NODES
def_bool y
depends on DISCONTIGMEM || NUMA
-config HAVE_MEMORY_PRESENT
- def_bool y
- depends on ARCH_HAVE_MEMORY_PRESENT || SPARSEMEM
-
#
# SPARSEMEM_EXTREME (which is the default) does some bootmem
-# allocations when memory_present() is called. If this cannot
+# allocations when sparse_init() is called. If this cannot
# be done on your architecture, select this option. However,
# statically allocating the mem_section[] array can potentially
# consume vast quantities of .bss, so be careful.
--- a/mm/page_alloc.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/mm/page_alloc.c
@@ -6325,22 +6325,6 @@ void __meminit init_currently_empty_zone
}
/**
- * sparse_memory_present_with_active_regions - Call memory_present for each active range
- * @nid: The node to call memory_present for. If MAX_NUMNODES, all nodes will be used.
- *
- * If an architecture guarantees that all ranges registered contain no holes and may
- * be freed, this function may be used instead of calling memory_present() manually.
- */
-void __init sparse_memory_present_with_active_regions(int nid)
-{
- unsigned long start_pfn, end_pfn;
- int i, this_nid;
-
- for_each_mem_pfn_range(i, nid, &start_pfn, &end_pfn, &this_nid)
- memory_present(this_nid, start_pfn, end_pfn);
-}
-
-/**
* get_pfn_range_for_nid - Return the start and end page frames for a node
* @nid: The nid to return the range for. If MAX_NUMNODES, the min and max PFN are returned.
* @start_pfn: Passed by reference. On return, it will have the node start_pfn.
--- a/mm/sparse.c~mm-sparse-cleanup-the-code-surrounding-memory_present
+++ a/mm/sparse.c
@@ -249,7 +249,7 @@ void __init subsection_map_init(unsigned
#endif
/* Record a memory area against a node. */
-void __init memory_present(int nid, unsigned long start, unsigned long end)
+static void __init memory_present(int nid, unsigned long start, unsigned long end)
{
unsigned long pfn;
@@ -285,11 +285,11 @@ void __init memory_present(int nid, unsi
}
/*
- * Mark all memblocks as present using memory_present(). This is a
- * convenience function that is useful for a number of arches
- * to mark all of the systems memory as present during initialization.
+ * Mark all memblocks as present using memory_present().
+ * This is a convenience function that is useful to mark all of the systems
+ * memory as present during initialization.
*/
-void __init memblocks_present(void)
+static void __init memblocks_present(void)
{
struct memblock_region *reg;
@@ -574,9 +574,13 @@ failed:
*/
void __init sparse_init(void)
{
- unsigned long pnum_begin = first_present_section_nr();
- int nid_begin = sparse_early_nid(__nr_to_section(pnum_begin));
- unsigned long pnum_end, map_count = 1;
+ unsigned long pnum_end, pnum_begin, map_count = 1;
+ int nid_begin;
+
+ memblocks_present();
+
+ pnum_begin = first_present_section_nr();
+ nid_begin = sparse_early_nid(__nr_to_section(pnum_begin));
/* Setup pageblock_order for HUGETLB_PAGE_SIZE_VARIABLE */
set_pageblock_order();
_
Patches currently in -mm which might be from rppt@xxxxxxxxxxxxx are
