From: Alexandre Bounine <alexandre.bounine@xxxxxxx> Subject: rapidio/tsi721_dma: add channel mask and queue size parameters Add module parameters to allow load time configuration of DMA channels. Depending on application, performance of DMA data transfers can benefit from adjusted sizes of buffer descriptor ring and/or transaction requests queue. Having HW DMA channel selector mask allows to define which channels (from seven available) are controlled by the mport device driver and reserve some of them for direct use by other drivers. Link: http://lkml.kernel.org/r/1469125134-16523-5-git-send-email-alexandre.bounine@xxxxxxx Signed-off-by: Alexandre Bounine <alexandre.bounine@xxxxxxx> Tested-by: Barry Wood <barry.wood@xxxxxxx> Cc: Matt Porter <mporter@xxxxxxxxxxxxxxxxxxx> Cc: Andre van Herk <andre.van.herk@xxxxxxxxxxxxxxxxxxxxxxxxx> Cc: Barry Wood <barry.wood@xxxxxxx> Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx> --- Documentation/rapidio/tsi721.txt | 14 +++++++++++++ drivers/rapidio/devices/tsi721.h | 2 - drivers/rapidio/devices/tsi721_dma.c | 26 ++++++++++++++++--------- 3 files changed, 32 insertions(+), 10 deletions(-) diff -puN Documentation/rapidio/tsi721.txt~rapidio-tsi721_dma-add-channel-mask-and-queue-size-parameters Documentation/rapidio/tsi721.txt --- a/Documentation/rapidio/tsi721.txt~rapidio-tsi721_dma-add-channel-mask-and-queue-size-parameters +++ a/Documentation/rapidio/tsi721.txt @@ -25,6 +25,20 @@ fully compatible with RIONET driver (Eth This parameter can be changed dynamically. Use CONFIG_RAPIDIO_DEBUG=y to enable debug output at the top level. +- 'dma_desc_per_channel' - This parameter defines number of hardware buffer + descriptors allocated for each registered Tsi721 DMA channel. + Its default value is 128. + +- 'dma_txqueue_sz' - DMA transactions queue size. Defines number of pending + transaction requests that can be accepted by each DMA channel. + Default value is 16. + +- 'dma_sel' - DMA channel selection mask. Bitmask that defines which hardware + DMA channels (0 ... 6) will be registered with DmaEngine core. + If bit is set to 1, the corresponding DMA channel will be registered. + DMA channels not selected by this mask will not be used by this device + driver. Default value is 0x7f (use all channels). + II. Known problems None. diff -puN drivers/rapidio/devices/tsi721.h~rapidio-tsi721_dma-add-channel-mask-and-queue-size-parameters drivers/rapidio/devices/tsi721.h --- a/drivers/rapidio/devices/tsi721.h~rapidio-tsi721_dma-add-channel-mask-and-queue-size-parameters +++ a/drivers/rapidio/devices/tsi721.h @@ -661,7 +661,7 @@ enum dma_rtype { */ #define TSI721_DMA_CHNUM TSI721_DMA_MAXCH -#define TSI721_DMACH_MAINT 0 /* DMA channel for maint requests */ +#define TSI721_DMACH_MAINT 7 /* DMA channel for maint requests */ #define TSI721_DMACH_MAINT_NBD 32 /* Number of BDs for maint requests */ #define TSI721_DMACH_DMA 1 /* DMA channel for data transfers */ diff -puN drivers/rapidio/devices/tsi721_dma.c~rapidio-tsi721_dma-add-channel-mask-and-queue-size-parameters drivers/rapidio/devices/tsi721_dma.c --- a/drivers/rapidio/devices/tsi721_dma.c~rapidio-tsi721_dma-add-channel-mask-and-queue-size-parameters +++ a/drivers/rapidio/devices/tsi721_dma.c @@ -36,18 +36,26 @@ #include "tsi721.h" -#define TSI721_DMA_TX_QUEUE_SZ 16 /* number of transaction descriptors */ - #ifdef CONFIG_PCI_MSI static irqreturn_t tsi721_bdma_msix(int irq, void *ptr); #endif static int tsi721_submit_sg(struct tsi721_tx_desc *desc); static unsigned int dma_desc_per_channel = 128; -module_param(dma_desc_per_channel, uint, S_IWUSR | S_IRUGO); +module_param(dma_desc_per_channel, uint, S_IRUGO); MODULE_PARM_DESC(dma_desc_per_channel, "Number of DMA descriptors per channel (default: 128)"); +static unsigned int dma_txqueue_sz = 16; +module_param(dma_txqueue_sz, uint, S_IRUGO); +MODULE_PARM_DESC(dma_txqueue_sz, + "DMA Transactions Queue Size (default: 16)"); + +static u8 dma_sel = 0x7f; +module_param(dma_sel, byte, S_IRUGO); +MODULE_PARM_DESC(dma_sel, + "DMA Channel Selection Mask (default: 0x7f = all)"); + static inline struct tsi721_bdma_chan *to_tsi721_chan(struct dma_chan *chan) { return container_of(chan, struct tsi721_bdma_chan, dchan); @@ -732,7 +740,7 @@ static int tsi721_alloc_chan_resources(s tsi_debug(DMA, &dchan->dev->device, "DMAC%d", bdma_chan->id); if (bdma_chan->bd_base) - return TSI721_DMA_TX_QUEUE_SZ; + return dma_txqueue_sz; /* Initialize BDMA channel */ if (tsi721_bdma_ch_init(bdma_chan, dma_desc_per_channel)) { @@ -742,7 +750,7 @@ static int tsi721_alloc_chan_resources(s } /* Allocate queue of transaction descriptors */ - desc = kcalloc(TSI721_DMA_TX_QUEUE_SZ, sizeof(struct tsi721_tx_desc), + desc = kcalloc(dma_txqueue_sz, sizeof(struct tsi721_tx_desc), GFP_ATOMIC); if (!desc) { tsi_err(&dchan->dev->device, @@ -754,7 +762,7 @@ static int tsi721_alloc_chan_resources(s bdma_chan->tx_desc = desc; - for (i = 0; i < TSI721_DMA_TX_QUEUE_SZ; i++) { + for (i = 0; i < dma_txqueue_sz; i++) { dma_async_tx_descriptor_init(&desc[i].txd, dchan); desc[i].txd.tx_submit = tsi721_tx_submit; desc[i].txd.flags = DMA_CTRL_ACK; @@ -766,7 +774,7 @@ static int tsi721_alloc_chan_resources(s bdma_chan->active = true; tsi721_bdma_interrupt_enable(bdma_chan, 1); - return TSI721_DMA_TX_QUEUE_SZ; + return dma_txqueue_sz; } static void tsi721_sync_dma_irq(struct tsi721_bdma_chan *bdma_chan) @@ -962,7 +970,7 @@ void tsi721_dma_stop_all(struct tsi721_d int i; for (i = 0; i < TSI721_DMA_MAXCH; i++) { - if (i != TSI721_DMACH_MAINT) + if ((i != TSI721_DMACH_MAINT) && (dma_sel & (1 << i))) tsi721_dma_stop(&priv->bdma[i]); } } @@ -979,7 +987,7 @@ int tsi721_register_dma(struct tsi721_de for (i = 0; i < TSI721_DMA_MAXCH; i++) { struct tsi721_bdma_chan *bdma_chan = &priv->bdma[i]; - if (i == TSI721_DMACH_MAINT) + if ((i == TSI721_DMACH_MAINT) || (dma_sel & (1 << i)) == 0) continue; bdma_chan->regs = priv->regs + TSI721_DMAC_BASE(i); _ -- To unsubscribe from this list: send the line "unsubscribe mm-commits" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
