The patch titled
Subject: clk: RK808: add clkout driver for RK808
has been removed from the -mm tree. Its filename was
clk-rk808-add-clkout-driver-for-rk808.patch
This patch was dropped because it was merged into mainline or a subsystem tree
------------------------------------------------------
From: Chris Zhong <zyw@xxxxxxxxxxxxxx>
Subject: clk: RK808: add clkout driver for RK808
This is the initial version of the RK808 PMIC. This is a power management
IC for multimedia products. It provides regulators that are able to
supply power to processor cores and other components. The chip provides
other modules including RTC, Clockout.
Signed-off-by: Chris Zhong <zyw@xxxxxxxxxxxxxx>
Reviewed-by: Doug Anderson <dianders@xxxxxxxxxxxx>
Tested-by: Doug Anderson <dianders@xxxxxxxxxxxx>
Tested-by: Heiko Stuebner <heiko@xxxxxxxxx>
Cc: Pawel Moll <pawel.moll@xxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
Cc: Samuel Ortiz <sameo@xxxxxxxxxxxxxxx> says:
Cc: Alessandro Zummo <a.zummo@xxxxxxxxxxxx>
Cc: Olof Johansson <olof@xxxxxxxxx>
Cc: Dmitry Torokhov <dtor@xxxxxxxxxxxx>
Cc: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
Cc: Kever Yang <kever.yang@xxxxxxxxxxxxxx>
Cc: Li Zhong <zhong@xxxxxxxxxxxxxxxxxx>
Cc: Russell King <rmk@xxxxxxxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/clk/Kconfig | 9 ++
drivers/clk/Makefile | 1
drivers/clk/clk-rk808.c | 170 ++++++++++++++++++++++++++++++++++++++
3 files changed, 180 insertions(+)
diff -puN drivers/clk/Kconfig~clk-rk808-add-clkout-driver-for-rk808 drivers/clk/Kconfig
--- a/drivers/clk/Kconfig~clk-rk808-add-clkout-driver-for-rk808
+++ a/drivers/clk/Kconfig
@@ -38,6 +38,15 @@ config COMMON_CLK_MAX77686
---help---
This driver supports Maxim 77686 crystal oscillator clock.
+config COMMON_CLK_RK808
+ tristate "Clock driver for RK808"
+ depends on MFD_RK808
+ ---help---
+ This driver supports RK808 crystal oscillator clock. These
+ multi-function devices have two fixed-rate oscillators,
+ clocked at 32KHz each. Clkout1 is always on, Clkout2 can off
+ by control register.
+
config COMMON_CLK_SI5351
tristate "Clock driver for SiLabs 5351A/B/C"
depends on I2C
diff -puN drivers/clk/Makefile~clk-rk808-add-clkout-driver-for-rk808 drivers/clk/Makefile
--- a/drivers/clk/Makefile~clk-rk808-add-clkout-driver-for-rk808
+++ a/drivers/clk/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_ARCH_NOMADIK) += clk-nomad
obj-$(CONFIG_ARCH_NSPIRE) += clk-nspire.o
obj-$(CONFIG_COMMON_CLK_PALMAS) += clk-palmas.o
obj-$(CONFIG_CLK_PPC_CORENET) += clk-ppc-corenet.o
+obj-$(CONFIG_COMMON_CLK_RK808) += clk-rk808.o
obj-$(CONFIG_COMMON_CLK_S2MPS11) += clk-s2mps11.o
obj-$(CONFIG_COMMON_CLK_SI5351) += clk-si5351.o
obj-$(CONFIG_COMMON_CLK_SI570) += clk-si570.o
diff -puN /dev/null drivers/clk/clk-rk808.c
--- /dev/null
+++ a/drivers/clk/clk-rk808.c
@@ -0,0 +1,170 @@
+/*
+ * Clkout driver for Rockchip RK808
+ *
+ * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Author:Chris Zhong <zyw@xxxxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/rk808.h>
+#include <linux/i2c.h>
+
+#define RK808_NR_OUTPUT 2
+
+struct rk808_clkout {
+ struct rk808 *rk808;
+ struct clk_onecell_data clk_data;
+ struct clk_hw clkout1_hw;
+ struct clk_hw clkout2_hw;
+};
+
+static unsigned long rk808_clkout_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return 32768;
+}
+
+static int rk808_clkout2_enable(struct clk_hw *hw, bool enable)
+{
+ struct rk808_clkout *rk808_clkout = container_of(hw,
+ struct rk808_clkout,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clkout->rk808;
+
+ return regmap_update_bits(rk808->regmap, RK808_CLK32OUT_REG,
+ CLK32KOUT2_EN, enable ? CLK32KOUT2_EN : 0);
+}
+
+static int rk808_clkout2_prepare(struct clk_hw *hw)
+{
+ return rk808_clkout2_enable(hw, true);
+}
+
+static void rk808_clkout2_unprepare(struct clk_hw *hw)
+{
+ rk808_clkout2_enable(hw, false);
+}
+
+static int rk808_clkout2_is_prepared(struct clk_hw *hw)
+{
+ struct rk808_clkout *rk808_clkout = container_of(hw,
+ struct rk808_clkout,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clkout->rk808;
+ uint32_t val;
+
+ int ret = regmap_read(rk808->regmap, RK808_CLK32OUT_REG, &val);
+
+ if (ret < 0)
+ return ret;
+
+ return (val & CLK32KOUT2_EN) ? 1 : 0;
+}
+
+static const struct clk_ops rk808_clkout1_ops = {
+ .recalc_rate = rk808_clkout_recalc_rate,
+};
+
+static const struct clk_ops rk808_clkout2_ops = {
+ .prepare = rk808_clkout2_prepare,
+ .unprepare = rk808_clkout2_unprepare,
+ .is_prepared = rk808_clkout2_is_prepared,
+ .recalc_rate = rk808_clkout_recalc_rate,
+};
+
+static int rk808_clkout_probe(struct platform_device *pdev)
+{
+ struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
+ struct i2c_client *client = rk808->i2c;
+ struct device_node *node = client->dev.of_node;
+ struct clk_init_data init = {};
+ struct clk **clk_table;
+ struct rk808_clkout *rk808_clkout;
+
+ rk808_clkout = devm_kzalloc(&client->dev,
+ sizeof(*rk808_clkout), GFP_KERNEL);
+ if (!rk808_clkout)
+ return -ENOMEM;
+
+ rk808_clkout->rk808 = rk808;
+
+ clk_table = devm_kcalloc(&client->dev, RK808_NR_OUTPUT,
+ sizeof(struct clk *), GFP_KERNEL);
+ if (!clk_table)
+ return -ENOMEM;
+
+ init.flags = CLK_IS_ROOT;
+ init.parent_names = NULL;
+ init.num_parents = 0;
+ init.name = "rk808-clkout1";
+ init.ops = &rk808_clkout1_ops;
+ rk808_clkout->clkout1_hw.init = &init;
+
+ /* optional override of the clockname */
+ of_property_read_string_index(node, "clock-output-names",
+ 0, &init.name);
+
+ clk_table[0] = devm_clk_register(&client->dev,
+ &rk808_clkout->clkout1_hw);
+ if (IS_ERR(clk_table[0]))
+ return PTR_ERR(clk_table[0]);
+
+ init.name = "rk808-clkout2";
+ init.ops = &rk808_clkout2_ops;
+ rk808_clkout->clkout2_hw.init = &init;
+
+ /* optional override of the clockname */
+ of_property_read_string_index(node, "clock-output-names",
+ 1, &init.name);
+
+ clk_table[1] = devm_clk_register(&client->dev,
+ &rk808_clkout->clkout2_hw);
+ if (IS_ERR(clk_table[1]))
+ return PTR_ERR(clk_table[1]);
+
+ rk808_clkout->clk_data.clks = clk_table;
+ rk808_clkout->clk_data.clk_num = RK808_NR_OUTPUT;
+
+ return of_clk_add_provider(node, of_clk_src_onecell_get,
+ &rk808_clkout->clk_data);
+}
+
+static int rk808_clkout_remove(struct platform_device *pdev)
+{
+ struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
+ struct i2c_client *client = rk808->i2c;
+ struct device_node *node = client->dev.of_node;
+
+ of_clk_del_provider(node);
+
+ return 0;
+}
+
+static struct platform_driver rk808_clkout_driver = {
+ .probe = rk808_clkout_probe,
+ .remove = rk808_clkout_remove,
+ .driver = {
+ .name = "rk808-clkout",
+ },
+};
+
+module_platform_driver(rk808_clkout_driver);
+
+MODULE_DESCRIPTION("Clkout driver for the rk808 series PMICs");
+MODULE_AUTHOR("Chris Zhong <zyw@xxxxxxxxxxxxxx>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:rk808-clkout");
_
Patches currently in -mm which might be from zyw@xxxxxxxxxxxxxx are
origin.patch
linux-next.patch
--
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
