The patch titled
serial: add tsi108 8250 serial support
has been added to the -mm tree. Its filename is
serial-add-tsi108-8250-serial-support.patch
See http://www.zip.com.au/~akpm/linux/patches/stuff/added-to-mm.txt to find
out what to do about this
------------------------------------------------------
Subject: serial: add tsi108 8250 serial support
From: Zang Roy-r61911 <tie-fei.zang@xxxxxxxxxxxxx>
The following patch gets rid of CONFIG_TSI108_BRIDGE. I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.
(1) the reason to rewrite serial_in:
TSI108 rev Z1 version ERRATA. Reading the UART's Interrupt
Identification Register (IIR) clears the Transmit Holding Register
Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
are not enabled in the Interrupt Enable Register (IER). This leads to
loss of the interrupts. Interrupts are not cleared when reading UART
registers as 32-bit word.
(2) the reason to rewrite serial_out:
Check for UART_IER_UUE bit in the autoconfig routine. This section
of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
reserved for internal use. They are R/W bits. In addition to
incorrect identification, changing these bits (from 00) will make
Tsi108/109 UART non-functional.
Cc: Russell King <rmk@xxxxxxxxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxx>
---
drivers/serial/8250.c | 12 ++++++++++++
include/linux/serial_core.h | 1 +
2 files changed, 13 insertions(+)
diff -puN drivers/serial/8250.c~serial-add-tsi108-8250-serial-support drivers/serial/8250.c
--- a/drivers/serial/8250.c~serial-add-tsi108-8250-serial-support
+++ a/drivers/serial/8250.c
@@ -300,6 +300,7 @@ static inline int map_8250_out_reg(struc
static unsigned int serial_in(struct uart_8250_port *up, int offset)
{
+ unsigned int tmp;
offset = map_8250_in_reg(up, offset) << up->port.regshift;
switch (up->port.iotype) {
@@ -317,6 +318,13 @@ static unsigned int serial_in(struct uar
case UPIO_AU:
return __raw_readl(up->port.membase + offset);
#endif
+
+ case UPIO_TSI:
+ if (offset == UART_IIR) {
+ tmp = readl((u32 *)(up->port.membase + UART_RX));
+ return (cpu_to_le32(tmp) >> 8) & 0xff;
+ } else
+ return readb(up->port.membase + offset);
default:
return inb(up->port.iobase + offset);
@@ -347,6 +355,10 @@ serial_out(struct uart_8250_port *up, in
__raw_writel(value, up->port.membase + offset);
break;
#endif
+ case UPIO_TSI:
+ if (!((offset == UART_IER) && (value & UART_IER_UUE)))
+ writeb(value, up->port.membase + offset);
+ break;
default:
outb(value, up->port.iobase + offset);
diff -puN include/linux/serial_core.h~serial-add-tsi108-8250-serial-support include/linux/serial_core.h
--- a/include/linux/serial_core.h~serial-add-tsi108-8250-serial-support
+++ a/include/linux/serial_core.h
@@ -223,6 +223,7 @@ struct uart_port {
#define UPIO_MEM (2)
#define UPIO_MEM32 (3)
#define UPIO_AU (4) /* Au1x00 type IO */
+#define UPIO_TSI (5) /* Tsi108/109 type IO */
unsigned int read_status_mask; /* driver specific */
unsigned int ignore_status_mask; /* driver specific */
_
Patches currently in -mm which might be from tie-fei.zang@xxxxxxxxxxxxx are
serial-add-tsi108-8250-serial-support.patch
-
To unsubscribe from this list: send the line "unsubscribe mm-commits" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
