Since commit 3af5a67c86a3 ("MIPS: Fix early CM probing") the MT7621
has not been able to boot.
This patched caused mips_cm_probe() to be called before
mt7621.c::proc_soc_init().
prom_soc_init() has a comment explaining that mips_cm_probe()
"wipes out the bootloader config" and means that configuration
registers are no longer available. It has some code to re-enable
this config.
Before this re-enable code is run, the sysc register cannot be
read, so when SYSC_REG_CHIP_NAME0 is read, a garbage value
is returned and panic() is called.
If we move the config-repair code to the top of prom_soc_init(),
the registers can be read and boot can proceed.
Fixes: 3af5a67c86a3 ("MIPS: Fix early CM probing")
Signed-off-by: NeilBrown <neil@xxxxxxxxxx>
---
arch/mips/ralink/mt7621.c | 41 +++++++++++++++++++++--------------------
1 file changed, 21 insertions(+), 20 deletions(-)
diff --git a/arch/mips/ralink/mt7621.c b/arch/mips/ralink/mt7621.c
index 1b274742077d..5a1b19bebd5b 100644
--- a/arch/mips/ralink/mt7621.c
+++ b/arch/mips/ralink/mt7621.c
@@ -170,6 +170,27 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
u32 n1;
u32 rev;
+ /* Early detection of CMP support */
+ mips_cm_probe();
+ mips_cpc_probe();
+
+ if (mips_cps_numiocu(0)) {
+ /*
+ * mips_cm_probe() wipes out bootloader
+ * config for CM regions and we have to configure them
+ * again. This SoC cannot talk to pamlbus devices
+ * witout proper iocu region set up.
+ *
+ * FIXME: it would be better to do this with values
+ * from DT, but we need this very early because
+ * without this we cannot talk to pretty much anything
+ * including serial.
+ */
+ write_gcr_reg0_base(MT7621_PALMBUS_BASE);
+ write_gcr_reg0_mask(~MT7621_PALMBUS_SIZE |
+ CM_GCR_REGn_MASK_CMTGT_IOCU0);
+ }
+
n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
@@ -194,26 +215,6 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
rt2880_pinmux_data = mt7621_pinmux_data;
- /* Early detection of CMP support */
- mips_cm_probe();
- mips_cpc_probe();
-
- if (mips_cps_numiocu(0)) {
- /*
- * mips_cm_probe() wipes out bootloader
- * config for CM regions and we have to configure them
- * again. This SoC cannot talk to pamlbus devices
- * witout proper iocu region set up.
- *
- * FIXME: it would be better to do this with values
- * from DT, but we need this very early because
- * without this we cannot talk to pretty much anything
- * including serial.
- */
- write_gcr_reg0_base(MT7621_PALMBUS_BASE);
- write_gcr_reg0_mask(~MT7621_PALMBUS_SIZE |
- CM_GCR_REGn_MASK_CMTGT_IOCU0);
- }
if (!register_cps_smp_ops())
return;
--
2.14.0.rc0.dirty
Attachment:
signature.asc
Description: PGP signature
