Re: [PATCH 3/8] PCI: host: brcmstb: Broadcom PCIe Host Controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Run "git log --oneline drivers/pci/host" and make yours match, e.g.,

s/PCI: host: brcmstb: Broadcom PCIe Host Controller/
  PCI: brcmstb: Add Broadcom STB PCIe host controller driver/

On Tue, Oct 24, 2017 at 02:15:44PM -0400, Jim Quinlan wrote:
> This commit adds the basic Broadcom STB PCIe controller.  Missing is
> the ability to process MSI and also handle dma-ranges for inbound
> memory accesses.  These two functionalities are added in subsequent
> commits.
> 
> The PCIe block contains an MDIO interface.  This is a local interface
> only accessible by the PCIe controller.  It cannot be used or shared
> by any other HW.  As such, the small amount of code for this
> controller is included in this driver as there is little upside to put
> it elsewhere.
> 
> Signed-off-by: Jim Quinlan <jim2101024@xxxxxxxxx>
> ---
>  drivers/pci/host/Kconfig       |    8 +
>  drivers/pci/host/Makefile      |    1 +
>  drivers/pci/host/pci-brcmstb.c | 1195 ++++++++++++++++++++++++++++++++++++++++

Name this pcie-brcmstb.c.  I used to have the idea we should name
things "pci-" unless they explicitly used some PCIe interfaces or
something, but I think that just made it confusing for PCIe
controllers like yours.

>  drivers/pci/host/pci-brcmstb.h |   33 ++

Unless you need this include file elsewhere, just fold its contents
into the .c file.

>  4 files changed, 1237 insertions(+)
>  create mode 100644 drivers/pci/host/pci-brcmstb.c
>  create mode 100644 drivers/pci/host/pci-brcmstb.h
> 
> diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
> index b868803..b9b4f11 100644
> --- a/drivers/pci/host/Kconfig
> +++ b/drivers/pci/host/Kconfig
> @@ -220,4 +220,12 @@ config VMD
>  	  To compile this driver as a module, choose M here: the
>  	  module will be called vmd.
>  
> +config PCI_BRCMSTB

PCIE_BRCMSTB

> +	tristate "Broadcom Brcmstb PCIe platform host driver"
> +	depends on ARCH_BRCMSTB || BMIPS_GENERIC
> +	depends on OF
> +	depends on SOC_BRCMSTB
> +	default ARCH_BRCMSTB || BMIPS_GENERIC
> +	help
> +	  Adds support for Broadcom Settop Box PCIe host controller.
>  endmenu
> diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
> index 1238278..4398d2c 100644
> --- a/drivers/pci/host/Makefile
> +++ b/drivers/pci/host/Makefile
> @@ -21,6 +21,7 @@ obj-$(CONFIG_PCIE_ROCKCHIP) += pcie-rockchip.o
>  obj-$(CONFIG_PCIE_MEDIATEK) += pcie-mediatek.o
>  obj-$(CONFIG_PCIE_TANGO_SMP8759) += pcie-tango.o
>  obj-$(CONFIG_VMD) += vmd.o
> +obj-$(CONFIG_PCI_BRCMSTB) += pci-brcmstb.o
>  
>  # The following drivers are for devices that use the generic ACPI
>  # pci_root.c driver but don't support standard ECAM config access.
> diff --git a/drivers/pci/host/pci-brcmstb.c b/drivers/pci/host/pci-brcmstb.c
> new file mode 100644
> index 0000000..883b435
> --- /dev/null
> +++ b/drivers/pci/host/pci-brcmstb.c
> @@ -0,0 +1,1195 @@
> +/*
> + * Copyright (C) 2009 - 2017 Broadcom
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +#include <linux/clk.h>
> +#include <linux/compiler.h>
> +#include <linux/delay.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/ioport.h>
> +#include <linux/irqdomain.h>
> +#include <linux/kernel.h>
> +#include <linux/list.h>
> +#include <linux/log2.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_pci.h>
> +#include <linux/of_pci.h>
> +#include <linux/of_platform.h>
> +#include <linux/pci.h>
> +#include <linux/printk.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/sizes.h>
> +#include <linux/slab.h>
> +#include <soc/brcmstb/memory_api.h>
> +#include <linux/string.h>
> +#include <linux/types.h>
> +#include "pci-brcmstb.h"
> +
> +/* Broadcom Settop Box PCIE Register Offsets.  */

s/PCIE/PCIe/ in comments and other English text throughout.

> +#define PCIE_RC_CFG_PCIE_LINK_CAPABILITY		0x00b8
> +#define PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL		0x00bc
> +#define PCIE_RC_CFG_PCIE_ROOT_CAP_CONTROL		0x00c8
> +#define PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_2		0x00dc

Many of these look like they are describing the PCIe capability.  If
so, please define a Broadcom-specific base and use the already-defined
constants from include/uapi/linux/pci_regs.h, e.g., PCI_EXP_LNKCAP,
etc.

> +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1		0x0188
> +#define PCIE_RC_CFG_PRIV1_ID_VAL3			0x043c
> +#define PCIE_RC_DL_MDIO_ADDR				0x1100
> +#define PCIE_RC_DL_MDIO_WR_DATA				0x1104
> +#define PCIE_RC_DL_MDIO_RD_DATA				0x1108
> +#define PCIE_MISC_MISC_CTRL				0x4008
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO		0x400c
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI		0x4010
> +#define PCIE_MISC_RC_BAR1_CONFIG_LO			0x402c
> +#define PCIE_MISC_RC_BAR1_CONFIG_HI			0x4030
> +#define PCIE_MISC_RC_BAR2_CONFIG_LO			0x4034
> +#define PCIE_MISC_RC_BAR2_CONFIG_HI			0x4038
> +#define PCIE_MISC_RC_BAR3_CONFIG_LO			0x403c
> +#define PCIE_MISC_RC_BAR3_CONFIG_HI			0x4040
> +#define PCIE_MISC_PCIE_CTRL				0x4064
> +#define PCIE_MISC_PCIE_STATUS				0x4068
> +#define PCIE_MISC_REVISION				0x406c
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT	0x4070
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI		0x4080
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI		0x4084
> +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG			0x4204
> +
> +/* Broadcom Settop Box PCIE Register Field Shift, Mask Info.  */
> +#define PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_NEG_LINK_WIDTH_MASK  0x3f00000

Looks suspiciously like PCI_EXP_LNKSTA_NLW.

> +#define PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_NEG_LINK_WIDTH_SHIFT	0x14
> +#define PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_NEG_LINK_SPEED_MASK	0xf0000
> +#define PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_NEG_LINK_SPEED_SHIFT	0x10
> +#define PCIE_RC_CFG_PCIE_LINK_CAPABILITY_MAX_LINK_SPEED_MASK		0xf
> +#define PCIE_RC_CFG_PCIE_LINK_CAPABILITY_MAX_LINK_SPEED_SHIFT		0x0
> +#define PCIE_RC_CFG_PCIE_ROOT_CAP_CONTROL_RC_CRS_EN_MASK		0x10
> +#define PCIE_RC_CFG_PCIE_ROOT_CAP_CONTROL_RC_CRS_EN_SHIFT		0x4
> +#define	PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_2_TARGET_LINK_SPEED_MASK	0xf
> +#define PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_2_TARGET_LINK_SPEED_SHIFT	0x0
> +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR1_MASK	0x3
> +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR1_SHIFT	0x0
> +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK	0xc
> +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_SHIFT	0x2
> +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR3_MASK	0x30
> +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR3_SHIFT	0x4
> +#define PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK		0xffffff
> +#define PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_SHIFT		0x0
> +#define PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK			0x1000
> +#define PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_SHIFT			0xc
> +#define PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK		0x2000
> +#define PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_SHIFT		0xd
> +#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK			0x300000
> +#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_SHIFT		0x14
> +#define PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK			0xf8000000
> +#define PCIE_MISC_MISC_CTRL_SCB0_SIZE_SHIFT			0x1b
> +#define PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK			0x7c00000
> +#define PCIE_MISC_MISC_CTRL_SCB1_SIZE_SHIFT			0x16
> +#define PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK			0x1f
> +#define PCIE_MISC_MISC_CTRL_SCB2_SIZE_SHIFT			0x0
> +#define PCIE_MISC_RC_BAR1_CONFIG_LO_MATCH_ADDRESS_MASK		0xfffff000
> +#define PCIE_MISC_RC_BAR1_CONFIG_LO_MATCH_ADDRESS_SHIFT		0xc
> +#define PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK			0x1f
> +#define PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_SHIFT			0x0
> +#define PCIE_MISC_RC_BAR2_CONFIG_LO_MATCH_ADDRESS_MASK		0xfffff000
> +#define PCIE_MISC_RC_BAR2_CONFIG_LO_MATCH_ADDRESS_SHIFT		0xc
> +#define PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK			0x1f
> +#define PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_SHIFT			0x0
> +#define PCIE_MISC_RC_BAR3_CONFIG_LO_MATCH_ADDRESS_MASK		0xfffff000
> +#define PCIE_MISC_RC_BAR3_CONFIG_LO_MATCH_ADDRESS_SHIFT		0xc
> +#define PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK			0x1f
> +#define PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_SHIFT			0x0
> +#define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK			0x4
> +#define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_SHIFT			0x2
> +#define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK		0x1
> +#define PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_SHIFT		0x0
> +#define PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK			0x80
> +#define PCIE_MISC_PCIE_STATUS_PCIE_PORT_SHIFT			0x7
> +#define PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_MASK		0x20
> +#define PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_SHIFT		0x5
> +#define PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK		0x10
> +#define PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_SHIFT		0x4
> +#define PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK		0x40
> +#define PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_SHIFT		0x6
> +#define PCIE_MISC_REVISION_MAJMIN_MASK				0xffff
> +#define PCIE_MISC_REVISION_MAJMIN_SHIFT				0
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK	0xfff00000
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_SHIFT	0x14
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK	0xfff0
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_SHIFT	0x4
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_NUM_MASK_BITS	0xc
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_MASK		0xff
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_SHIFT	0x0
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK	0xff
> +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_SHIFT	0x0
> +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK	0x2
> +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_SHIFT 0x1
> +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK		0x08000000
> +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_SHIFT	0x1b
> +#define PCIE_RGR1_SW_INIT_1_PERST_MASK				0x1
> +#define PCIE_RGR1_SW_INIT_1_PERST_SHIFT				0x0

Many of these definitions aren't used, and I'm dubious about the value
of including them all.

> +#define BRCM_NUM_PCI_OUT_WINS		0x4
> +#define BRCM_MAX_SCB			0x4
> +
> +#define BRCM_MSI_TARGET_ADDR_LT_4GB	0x0fffffffcULL
> +#define BRCM_MSI_TARGET_ADDR_GT_4GB	0xffffffffcULL
> +
> +#define BURST_SIZE_128			0
> +#define BURST_SIZE_256			1
> +#define BURST_SIZE_512			2
> +
> +/* Offsets from PCIE_INTR2_CPU_BASE */
> +#define STATUS				0x0
> +#define SET				0x4
> +#define CLR				0x8
> +#define MASK_STATUS			0xc
> +#define MASK_SET			0x10
> +#define MASK_CLR			0x14
> +
> +#define PCI_BUSNUM_SHIFT		20
> +#define PCI_SLOT_SHIFT			15
> +#define PCI_FUNC_SHIFT			12
> +
> +#if defined(__BIG_ENDIAN)
> +#define	DATA_ENDIAN		2	/* PCI->DDR inbound accesses */
> +#define MMIO_ENDIAN		2	/* CPU->PCI outbound accesses */
> +#else
> +#define	DATA_ENDIAN		0
> +#define MMIO_ENDIAN		0
> +#endif
> +
> +#define MDIO_PORT0		0x0
> +#define MDIO_DATA_MASK		0x7fffffff
> +#define MDIO_DATA_SHIFT		0x0
> +#define MDIO_PORT_MASK		0xf0000
> +#define MDIO_PORT_SHIFT		0x16
> +#define MDIO_REGAD_MASK		0xffff
> +#define MDIO_REGAD_SHIFT	0x0
> +#define MDIO_CMD_MASK		0xfff00000
> +#define MDIO_CMD_SHIFT		0x14
> +#define MDIO_CMD_READ		0x1
> +#define MDIO_CMD_WRITE		0x0
> +#define MDIO_DATA_DONE_MASK	0x80000000
> +#define MDIO_RD_DONE(x)		(((x) & MDIO_DATA_DONE_MASK) ? 1 : 0)
> +#define MDIO_WT_DONE(x)		(((x) & MDIO_DATA_DONE_MASK) ? 0 : 1)
> +#define SSC_REGS_ADDR		0x1100
> +#define SET_ADDR_OFFSET		0x1f
> +#define SSC_CNTL_OFFSET		0x2
> +#define SSC_CNTL_OVRD_EN_MASK	0x8000
> +#define SSC_CNTL_OVRD_EN_SHIFT	0xf
> +#define SSC_CNTL_OVRD_VAL_MASK	0x4000
> +#define SSC_CNTL_OVRD_VAL_SHIFT	0xe
> +#define SSC_STATUS_OFFSET	0x1
> +#define SSC_STATUS_SSC_MASK	0x400
> +#define SSC_STATUS_SSC_SHIFT	0xa
> +#define SSC_STATUS_PLL_LOCK_MASK	0x800
> +#define SSC_STATUS_PLL_LOCK_SHIFT	0xb
> +
> +#define IDX_ADDR(pcie)	\
> +	((pcie)->reg_offsets[EXT_CFG_INDEX])
> +#define DATA_ADDR(pcie)	\
> +	((pcie)->reg_offsets[EXT_CFG_DATA])
> +#define PCIE_RGR1_SW_INIT_1(pcie) \
> +	((pcie)->reg_offsets[RGR1_SW_INIT_1])
> +
> +enum {
> +	RGR1_SW_INIT_1,
> +	EXT_CFG_INDEX,
> +	EXT_CFG_DATA,
> +};
> +
> +enum {
> +	RGR1_SW_INIT_1_INIT_MASK,
> +	RGR1_SW_INIT_1_INIT_SHIFT,
> +	RGR1_SW_INIT_1_PERST_MASK,
> +	RGR1_SW_INIT_1_PERST_SHIFT,
> +};
> +
> +enum pcie_type {
> +	BCM7425,
> +	BCM7435,
> +	GENERIC,
> +	BCM7278,
> +};
> +
> +#define RD_FLD(base, reg, field) \
> +	rd_fld(base + reg, reg##_##field##_MASK, reg##_##field##_SHIFT)
> +#define WR_FLD(base, reg, field, val) \
> +	wr_fld(base + reg, reg##_##field##_MASK, reg##_##field##_SHIFT, val)
> +#define WR_FLD_RB(base, reg, field, val) \
> +	wr_fld_rb(base + reg, reg##_##field##_MASK, reg##_##field##_SHIFT, val)
> +#define WR_FLD_WITH_OFFSET(base, off, reg, field, val) \
> +	wr_fld(base + reg + off, reg##_##field##_MASK, \
> +	       reg##_##field##_SHIFT, val)
> +#define EXTRACT_FIELD(val, reg, field) \
> +	((val & reg##_##field##_MASK) >> reg##_##field##_SHIFT)
> +#define INSERT_FIELD(val, reg, field, field_val) \
> +	((val & ~reg##_##field##_MASK) | \
> +	 (reg##_##field##_MASK & (field_val << reg##_##field##_SHIFT)))
> +
> +struct pcie_cfg_data {
> +	const int *reg_field_info;
> +	const int *offsets;
> +	const enum pcie_type type;
> +};
> +
> +static const int pcie_reg_field_info[] = {
> +	[RGR1_SW_INIT_1_INIT_MASK] = 0x2,
> +	[RGR1_SW_INIT_1_INIT_SHIFT] = 0x1,
> +};
> +
> +static const int pcie_reg_field_info_bcm7278[] = {
> +	[RGR1_SW_INIT_1_INIT_MASK] = 0x1,
> +	[RGR1_SW_INIT_1_INIT_SHIFT] = 0x0,
> +};
> +
> +static const int pcie_offset_bcm7425[] = {
> +	[RGR1_SW_INIT_1] = 0x8010,
> +	[EXT_CFG_INDEX]  = 0x8300,
> +	[EXT_CFG_DATA]   = 0x8304,
> +};
> +
> +static const struct pcie_cfg_data bcm7425_cfg = {
> +	.reg_field_info	= pcie_reg_field_info,
> +	.offsets	= pcie_offset_bcm7425,
> +	.type		= BCM7425,
> +};
> +
> +static const int pcie_offsets[] = {
> +	[RGR1_SW_INIT_1] = 0x9210,
> +	[EXT_CFG_INDEX]  = 0x9000,
> +	[EXT_CFG_DATA]   = 0x9004,
> +};
> +
> +static const struct pcie_cfg_data bcm7435_cfg = {
> +	.reg_field_info	= pcie_reg_field_info,
> +	.offsets	= pcie_offsets,
> +	.type		= BCM7435,
> +};
> +
> +static const struct pcie_cfg_data generic_cfg = {
> +	.reg_field_info	= pcie_reg_field_info,
> +	.offsets	= pcie_offsets,
> +	.type		= GENERIC,
> +};
> +
> +static const int pcie_offset_bcm7278[] = {
> +	[RGR1_SW_INIT_1] = 0xc010,
> +	[EXT_CFG_INDEX] = 0x9000,
> +	[EXT_CFG_DATA] = 0x9004,
> +};
> +
> +static const struct pcie_cfg_data bcm7278_cfg = {
> +	.reg_field_info = pcie_reg_field_info_bcm7278,
> +	.offsets	= pcie_offset_bcm7278,
> +	.type		= BCM7278,
> +};
> +
> +static void __iomem *brcm_pci_map_cfg(struct pci_bus *bus, unsigned int devfn,
> +				      int where);
> +
> +static struct pci_ops brcm_pci_ops = {
> +	.map_bus = brcm_pci_map_cfg,
> +	.read = pci_generic_config_read32,
> +	.write = pci_generic_config_write32,

Ouch, does your hardware really not support 8- and 16-bit config
accesses?  As you probably know, that can lead to config space
corruption with devices that have RW1C bits in registers.

> +};
> +
> +struct brcm_dev_pwr_supply {
> +	struct list_head node;
> +	char name[32];
> +	struct regulator *regulator;
> +};
> +
> +struct brcm_window {
> +	dma_addr_t pci_addr;
> +	phys_addr_t cpu_addr;
> +	dma_addr_t size;
> +};
> +
> +/* Internal Bus Controller Information.*/
> +struct brcm_pcie {
> +	struct list_head	list;
> +	void __iomem		*base;
> +	char			name[BRCM_PCIE_NAME_SIZE];
> +	bool			suspended;
> +	struct clk		*clk;
> +	struct device_node	*dn;
> +	int			irq;
> +	int			num_out_wins;
> +	bool			ssc;
> +	int			gen;
> +	struct brcm_window	out_wins[BRCM_NUM_PCI_OUT_WINS];
> +	struct list_head	resources;
> +	struct device		*dev;
> +	struct list_head	pwr_supplies;
> +	unsigned int		rev;
> +	unsigned int		num;
> +	bool			bridge_setup_done;

Nobody else needs a "bridge_setup_done" variable; I'm skeptical that
you do.  Please use similar style to other drivers whenever possible.

> +	const int		*reg_offsets;
> +	const int		*reg_field_info;
> +	enum pcie_type		type;
> +	struct pci_bus		*root_bus;
> +	int			id;

Please reorder with more generic info at the top, e.g., "* dev",
"*base", "resources", etc., should be near the top, as other drivers
do.

> +};
> +
> +static struct list_head brcm_pcie = LIST_HEAD_INIT(brcm_pcie);

Do you really need a list of controllers?  It looks like this is only
used for remove.  If you get rid of the list, you probably don't need
brcm_pcie_lock either.

> +static phys_addr_t scb_size[BRCM_MAX_SCB];
> +static int num_memc;
> +static DEFINE_MUTEX(brcm_pcie_lock);
> +
> +/*
> + * The roundup_pow_of_two() from log2.h invokes
> + * __roundup_pow_of_two(unsigned long), but we really need a
> + * such a function to take a native u64 since unsigned long
> + * is 32 bits on some configurations.  So we provide this helper
> + * function below.
> + */
> +static u64 roundup_pow_of_two_64(u64 n)
> +{
> +	return 1ULL << fls64(n - 1);
> +}
> +
> +static int brcm_pcie_add_controller(struct brcm_pcie *pcie)
> +{
> +	mutex_lock(&brcm_pcie_lock);
> +	snprintf(pcie->name, sizeof(pcie->name) - 1, "PCIe%d", pcie->id);
> +	list_add_tail(&pcie->list, &brcm_pcie);
> +	mutex_unlock(&brcm_pcie_lock);
> +
> +	return 0;
> +}
> +
> +static void brcm_pcie_remove_controller(struct brcm_pcie *pcie)
> +{
> +	struct list_head *pos, *q;
> +	struct brcm_pcie *tmp;
> +
> +	mutex_lock(&brcm_pcie_lock);
> +	list_for_each_safe(pos, q, &brcm_pcie) {
> +		tmp = list_entry(pos, struct brcm_pcie, list);
> +		if (tmp == pcie) {
> +			list_del(pos);
> +			if (list_empty(&brcm_pcie))
> +				num_memc = 0;
> +			break;
> +		}
> +	}
> +	mutex_unlock(&brcm_pcie_lock);
> +}
> +
> +/* This is to convert the size of the inbound bar region to the
> + * non-liniear values of PCIE_X_MISC_RC_BAR[123]_CONFIG_LO.SIZE

Please use conventional comment style for multi-line comments, i.e.,

  /*
   * text ...
   */

> + */
> +int encode_ibar_size(u64 size)
> +{
> +	int log2_in = ilog2(size);
> +
> +	if (log2_in >= 12 && log2_in <= 15)
> +		/* Covers 4KB to 32KB (inclusive) */
> +		return (log2_in - 12) + 0x1c;
> +	else if (log2_in >= 16 && log2_in <= 37)
> +		/* Covers 64KB to 32GB, (inclusive) */
> +		return log2_in - 15;
> +	/* Something is awry so disable */
> +	return 0;
> +}
> +
> +static u32 mdio_form_pkt(int port, int regad, int cmd)
> +{
> +	u32 pkt = 0;
> +
> +	pkt |= (port << MDIO_PORT_SHIFT) & MDIO_PORT_MASK;
> +	pkt |= (regad << MDIO_REGAD_SHIFT) & MDIO_REGAD_MASK;
> +	pkt |= (cmd << MDIO_CMD_SHIFT) & MDIO_CMD_MASK;
> +
> +	return pkt;
> +}
> +
> +/* negative return value indicates error */
> +static int mdio_read(void __iomem *base, u8 port, u8 regad)
> +{
> +	int tries;
> +	u32 data;
> +
> +	bcm_writel(mdio_form_pkt(port, regad, MDIO_CMD_READ),
> +		   base + PCIE_RC_DL_MDIO_ADDR);
> +	bcm_readl(base + PCIE_RC_DL_MDIO_ADDR);
> +
> +	data = bcm_readl(base + PCIE_RC_DL_MDIO_RD_DATA);
> +	for (tries = 0; !MDIO_RD_DONE(data) && tries < 10; tries++) {
> +		udelay(10);
> +		data = bcm_readl(base + PCIE_RC_DL_MDIO_RD_DATA);
> +	}
> +
> +	return MDIO_RD_DONE(data)
> +		? (data & MDIO_DATA_MASK) >> MDIO_DATA_SHIFT
> +		: -EIO;
> +}
> +
> +/* negative return value indicates error */
> +static int mdio_write(void __iomem *base, u8 port, u8 regad, u16 wrdata)
> +{
> +	int tries;
> +	u32 data;
> +
> +	bcm_writel(mdio_form_pkt(port, regad, MDIO_CMD_WRITE),
> +		   base + PCIE_RC_DL_MDIO_ADDR);
> +	bcm_readl(base + PCIE_RC_DL_MDIO_ADDR);
> +	bcm_writel(MDIO_DATA_DONE_MASK | wrdata,
> +		   base + PCIE_RC_DL_MDIO_WR_DATA);
> +
> +	data = bcm_readl(base + PCIE_RC_DL_MDIO_WR_DATA);
> +	for (tries = 0; !MDIO_WT_DONE(data) && tries < 10; tries++) {
> +		udelay(10);
> +		data = bcm_readl(base + PCIE_RC_DL_MDIO_WR_DATA);
> +	}
> +
> +	return MDIO_WT_DONE(data) ? 0 : -EIO;
> +}
> +
> +static u32 rd_fld(void __iomem *p, u32 mask, int shift)
> +{
> +	return (bcm_readl(p) & mask) >> shift;
> +}
> +
> +static void wr_fld(void __iomem *p, u32 mask, int shift, u32 val)
> +{
> +	u32 reg = bcm_readl(p);
> +
> +	reg = (reg & ~mask) | ((val << shift) & mask);
> +	bcm_writel(reg, p);
> +}
> +
> +static void wr_fld_rb(void __iomem *p, u32 mask, int shift, u32 val)
> +{
> +	wr_fld(p, mask, shift, val);
> +	(void)bcm_readl(p);
> +}
> +
> +/* configures device for ssc mode; negative return value indicates error */
> +static int set_ssc(void __iomem *base)
> +{
> +	int tmp;
> +	u16 wrdata;
> +	int pll, ssc;
> +
> +	tmp = mdio_write(base, MDIO_PORT0, SET_ADDR_OFFSET, SSC_REGS_ADDR);
> +	if (tmp < 0)
> +		return tmp;
> +
> +	tmp = mdio_read(base, MDIO_PORT0, SSC_CNTL_OFFSET);
> +	if (tmp < 0)
> +		return tmp;
> +
> +	wrdata = INSERT_FIELD(tmp, SSC_CNTL_OVRD, EN, 1);
> +	wrdata = INSERT_FIELD(wrdata, SSC_CNTL_OVRD, VAL, 1);
> +	tmp = mdio_write(base, MDIO_PORT0, SSC_CNTL_OFFSET, wrdata);
> +	if (tmp < 0)
> +		return tmp;
> +
> +	usleep_range(1000, 2000);
> +	tmp = mdio_read(base, MDIO_PORT0, SSC_STATUS_OFFSET);
> +	if (tmp < 0)
> +		return tmp;
> +
> +	ssc = EXTRACT_FIELD(tmp, SSC_STATUS, SSC);
> +	pll = EXTRACT_FIELD(tmp, SSC_STATUS, PLL_LOCK);
> +
> +	return (ssc && pll) ? 0 : -EIO;
> +}
> +
> +/* limits operation to a specific generation (1, 2, or 3) */
> +static void set_gen(void __iomem *base, int gen)
> +{
> +	WR_FLD(base, PCIE_RC_CFG_PCIE_LINK_CAPABILITY, MAX_LINK_SPEED, gen);
> +	WR_FLD(base, PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL_2,
> +	       TARGET_LINK_SPEED, gen);
> +}
> +
> +static void set_pcie_outbound_win(struct brcm_pcie *pcie, unsigned int win,
> +				  phys_addr_t cpu_addr, dma_addr_t  pci_addr,
> +				  dma_addr_t size)
> +{
> +	void __iomem *base = pcie->base;
> +	phys_addr_t cpu_addr_mb, limit_addr_mb;
> +	u32 tmp;
> +
> +	/* Set the base of the pci_addr window */
> +	bcm_writel(lower_32_bits(pci_addr) + MMIO_ENDIAN,
> +		   base + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + (win * 8));
> +	bcm_writel(upper_32_bits(pci_addr),
> +		   base + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + (win * 8));
> +
> +	cpu_addr_mb = cpu_addr >> 20;
> +	limit_addr_mb = (cpu_addr + size - 1) >> 20;
> +
> +	/* Write the addr base low register */
> +	WR_FLD_WITH_OFFSET(base, (win * 4),
> +			   PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT,
> +			   BASE, cpu_addr_mb);
> +	/* Write the addr limit low register */
> +	WR_FLD_WITH_OFFSET(base, (win * 4),
> +			   PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT,
> +			   LIMIT, limit_addr_mb);
> +
> +	if (pcie->type != BCM7435 && pcie->type != BCM7425) {
> +		/* Write the cpu addr high register */
> +		tmp = (u32)(cpu_addr_mb >>
> +			PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_NUM_MASK_BITS);
> +		WR_FLD_WITH_OFFSET(base, (win * 8),
> +				   PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI,
> +				   BASE, tmp);
> +		/* Write the cpu limit high register */
> +		tmp = (u32)(limit_addr_mb >>
> +			PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_NUM_MASK_BITS);
> +		WR_FLD_WITH_OFFSET(base, (win * 8),
> +				   PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI,
> +				   LIMIT, tmp);
> +	}
> +}
> +
> +static int is_pcie_link_up(struct brcm_pcie *pcie, bool silent)

Please use function names similar to other drivers, e.g.,
brcm_pcie_link_up() in this case.

> +{
> +	void __iomem *base = pcie->base;
> +	u32 val = bcm_readl(base + PCIE_MISC_PCIE_STATUS);
> +	u32 dla = EXTRACT_FIELD(val, PCIE_MISC_PCIE_STATUS, PCIE_DL_ACTIVE);
> +	u32 plu = EXTRACT_FIELD(val, PCIE_MISC_PCIE_STATUS, PCIE_PHYLINKUP);
> +	u32 rc = EXTRACT_FIELD(val, PCIE_MISC_PCIE_STATUS, PCIE_PORT);
> +
> +	if (!rc && !silent)
> +		dev_err(pcie->dev, "controller configured in EP mode\n");
> +
> +	return  (rc && dla && plu) ? 1 : 0;
> +}
> +
> +static inline void brcm_pcie_bridge_sw_init_set(struct brcm_pcie *pcie,
> +						unsigned int val)
> +{
> +	unsigned int offset;
> +	unsigned int shift = pcie->reg_field_info[RGR1_SW_INIT_1_INIT_SHIFT];
> +	u32 mask =  pcie->reg_field_info[RGR1_SW_INIT_1_INIT_MASK];
> +
> +	if (pcie->type != BCM7278) {
> +		wr_fld_rb(pcie->base + PCIE_RGR1_SW_INIT_1(pcie), mask, shift,
> +			  val);
> +	} else if (of_machine_is_compatible("brcm,bcm7278a0")) {
> +		/* The two PCIE instance on 7278a0 are not even consistent with
> +		 * respect to each other for internal offsets, here we offset
> +		 * by 0x14000 + RGR1_SW_INIT_1's relative offset to account for
> +		 * that.
> +		 */
> +		offset = pcie->id ? 0x14010 : pcie->reg_offsets[RGR1_SW_INIT_1];
> +		wr_fld_rb(pcie->base + offset, mask, shift, val);
> +	} else {
> +		wr_fld_rb(pcie->base + PCIE_RGR1_SW_INIT_1(pcie), mask, shift,
> +			  val);
> +	}
> +}
> +
> +static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie,
> +				       unsigned int val)
> +{
> +	if (pcie->type != BCM7278)
> +		wr_fld_rb(pcie->base + PCIE_RGR1_SW_INIT_1(pcie),
> +			  PCIE_RGR1_SW_INIT_1_PERST_MASK,
> +			  PCIE_RGR1_SW_INIT_1_PERST_SHIFT, val);
> +	else
> +		/* Assert = 0, de-assert = 1 on 7278 */
> +		WR_FLD_RB(pcie->base, PCIE_MISC_PCIE_CTRL, PCIE_PERSTB, !val);
> +}
> +
> +static int brcm_parse_ranges(struct brcm_pcie *pcie)
> +{
> +	struct resource_entry *win;
> +	int ret;
> +
> +	ret = of_pci_get_host_bridge_resources(pcie->dn, 0, 0xff,
> +					       &pcie->resources, NULL);
> +	if (ret) {
> +		dev_err(pcie->dev, "failed to get host resources\n");
> +		return ret;
> +	}
> +
> +	resource_list_for_each_entry(win, &pcie->resources) {
> +		struct resource *parent, *res = win->res;
> +		dma_addr_t offset = (dma_addr_t)win->offset;
> +
> +		if (resource_type(res) == IORESOURCE_IO) {
> +			parent = &ioport_resource;
> +		} else if (resource_type(res) == IORESOURCE_MEM) {
> +			if (pcie->num_out_wins >= BRCM_NUM_PCI_OUT_WINS) {
> +				dev_err(pcie->dev, "too many outbound wins\n");
> +				return -EINVAL;
> +			}
> +			pcie->out_wins[pcie->num_out_wins].cpu_addr
> +				= (phys_addr_t)res->start;
> +			pcie->out_wins[pcie->num_out_wins].pci_addr
> +				= (dma_addr_t)(res->start
> +					       - (phys_addr_t)offset);
> +			pcie->out_wins[pcie->num_out_wins].size
> +				= (dma_addr_t)(res->end - res->start + 1);
> +			pcie->num_out_wins++;
> +			parent = &iomem_resource;
> +		} else {
> +			continue;
> +		}
> +
> +		ret = devm_request_resource(pcie->dev, parent, res);
> +		if (ret) {
> +			dev_err(pcie->dev, "failed to get res %pR\n", res);
> +			return ret;
> +		}
> +	}
> +	return 0;
> +}
> +
> +static void set_regulators(struct brcm_pcie *pcie, bool on)
> +{
> +	struct list_head *pos;
> +
> +	list_for_each(pos, &pcie->pwr_supplies) {
> +		struct brcm_dev_pwr_supply *supply
> +			= list_entry(pos, struct brcm_dev_pwr_supply, node);
> +
> +		if (on && regulator_enable(supply->regulator))
> +			pr_debug("Unable to turn on %s supply.\n",
> +				 supply->name);
> +		else if (!on && regulator_disable(supply->regulator))
> +			pr_debug("Unable to turn off %s supply.\n",
> +				 supply->name);
> +	}
> +}
> +
> +static void brcm_pcie_setup_prep(struct brcm_pcie *pcie)
> +{
> +	void __iomem *base = pcie->base;
> +	unsigned int scb_size_val;
> +	u64 rc_bar2_size = 0, rc_bar2_offset = 0, total_mem_size = 0;
> +	u32 tmp, burst;
> +	int i;
> +
> +	/* reset the bridge and the endpoint device */
> +	/* field: PCIE_BRIDGE_SW_INIT = 1 */
> +	brcm_pcie_bridge_sw_init_set(pcie, 1);
> +
> +	/* field: PCIE_SW_PERST = 1, on 7278, we start de-asserted already */
> +	if (pcie->type != BCM7278)
> +		brcm_pcie_perst_set(pcie, 1);
> +
> +	usleep_range(100, 200);
> +
> +	/* take the bridge out of reset */
> +	/* field: PCIE_BRIDGE_SW_INIT = 0 */
> +	brcm_pcie_bridge_sw_init_set(pcie, 0);
> +
> +	WR_FLD_RB(base, PCIE_MISC_HARD_PCIE_HARD_DEBUG, SERDES_IDDQ, 0);
> +	/* wait for serdes to be stable */
> +	usleep_range(100, 200);
> +
> +	/* Grab the PCIe hw revision number */
> +	tmp = bcm_readl(base + PCIE_MISC_REVISION);
> +	pcie->rev = EXTRACT_FIELD(tmp, PCIE_MISC_REVISION, MAJMIN);
> +
> +	/* Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN */
> +	tmp = INSERT_FIELD(0, PCIE_MISC_MISC_CTRL, SCB_ACCESS_EN, 1);
> +	tmp = INSERT_FIELD(tmp, PCIE_MISC_MISC_CTRL, CFG_READ_UR_MODE, 1);
> +	burst = (pcie->type == GENERIC || pcie->type == BCM7278)
> +		? BURST_SIZE_512 : BURST_SIZE_256;
> +	tmp = INSERT_FIELD(tmp, PCIE_MISC_MISC_CTRL, MAX_BURST_SIZE, burst);
> +	bcm_writel(tmp, base + PCIE_MISC_MISC_CTRL);
> +
> +	/* Set up inbound memory view for the EP (called RC_BAR2,
> +	 * not to be confused with the BARs that are advertised by
> +	 * the EP).

Multi-line comment style here and below.

> +	 */
> +	for (i = 0; i < num_memc; i++)
> +		total_mem_size += scb_size[i];
> +
> +	/* The PCI host controller by design must set the inbound
> +	 * viewport to be a contiguous arrangement of all of the
> +	 * system's memory.  In addition, its size mut be a power of
> +	 * two.  To further complicate matters, the viewport must
> +	 * start on a pci-address that is aligned on a multiple of its
> +	 * size.  If a portion of the viewport does not represent
> +	 * system memory -- e.g. 3GB of memory requires a 4GB viewport
> +	 * -- we can map the outbound memory in or after 3GB and even
> +	 * though the viewport will overlap the outbound memory the
> +	 * controller will know to send outbound memory downstream and
> +	 * everything else upstream.
> +	 */
> +	rc_bar2_size = roundup_pow_of_two_64(total_mem_size);
> +
> +	/* Set simple configuration based on memory sizes
> +	 * only.  We always start the viewport at address 0.
> +	 */
> +	rc_bar2_offset = 0;
> +
> +	tmp = lower_32_bits(rc_bar2_offset);
> +	tmp = INSERT_FIELD(tmp, PCIE_MISC_RC_BAR2_CONFIG_LO, SIZE,
> +			   encode_ibar_size(rc_bar2_size));
> +	bcm_writel(tmp, base + PCIE_MISC_RC_BAR2_CONFIG_LO);
> +	bcm_writel(upper_32_bits(rc_bar2_offset),
> +		   base + PCIE_MISC_RC_BAR2_CONFIG_HI);
> +
> +	/* field: SCB0_SIZE, default = 0xf (1 GB) */
> +	scb_size_val = scb_size[0]
> +		? ilog2(scb_size[0]) - 15 : 0xf;
> +	WR_FLD(base, PCIE_MISC_MISC_CTRL, SCB0_SIZE, scb_size_val);
> +
> +	/* field: SCB1_SIZE, default = 0xf (1 GB) */
> +	if (num_memc > 1) {
> +		scb_size_val = scb_size[1]
> +			? ilog2(scb_size[1]) - 15 : 0xf;
> +		WR_FLD(base, PCIE_MISC_MISC_CTRL, SCB1_SIZE, scb_size_val);
> +	}
> +
> +	/* field: SCB2_SIZE, default = 0xf (1 GB) */
> +	if (num_memc > 2) {
> +		scb_size_val = scb_size[2]
> +			? ilog2(scb_size[2]) - 15 : 0xf;
> +		WR_FLD(base, PCIE_MISC_MISC_CTRL, SCB2_SIZE, scb_size_val);
> +	}
> +
> +	/* disable the PCIE->GISB memory window (RC_BAR1) */
> +	WR_FLD(base, PCIE_MISC_RC_BAR1_CONFIG_LO, SIZE, 0);
> +
> +	/* disable the PCIE->SCB memory window (RC_BAR3) */
> +	WR_FLD(base, PCIE_MISC_RC_BAR3_CONFIG_LO, SIZE, 0);
> +
> +	if (!pcie->suspended) {
> +		/* clear any interrupts we find on boot */
> +		bcm_writel(0xffffffff, base + PCIE_INTR2_CPU_BASE + CLR);
> +		(void)bcm_readl(base + PCIE_INTR2_CPU_BASE + CLR);
> +	}
> +
> +	/* Mask all interrupts since we are not handling any yet */
> +	bcm_writel(0xffffffff, base + PCIE_INTR2_CPU_BASE + MASK_SET);
> +	(void)bcm_readl(base + PCIE_INTR2_CPU_BASE + MASK_SET);
> +
> +	if (pcie->gen)
> +		set_gen(base, pcie->gen);
> +
> +	/* take the EP device out of reset */
> +	/* field: PCIE_SW_PERST = 0 */
> +	brcm_pcie_perst_set(pcie, 0);
> +}
> +
> +static const char *link_speed_to_str(int s)
> +{
> +	switch (s) {
> +	case 1:
> +		return "2.5";
> +	case 2:
> +		return "5.0";
> +	case 3:
> +		return "8.0";
> +	default:
> +		break;
> +	}
> +	return "???";
> +}
> +
> +static int brcm_pcie_setup_bridge(struct brcm_pcie *pcie)
> +{
> +	void __iomem *base = pcie->base;
> +	const int limit = pcie->suspended ? 1000 : 100;
> +	unsigned int status;
> +	int i, j, ret;
> +	u32 neg_width, neg_speed;
> +	bool ssc_good = false;
> +
> +	/* Give the RC/EP time to wake up, before trying to configure RC.
> +	 * Intermittently check status for link-up, up to a total of 100ms
> +	 * when we don't know if the device is there, and up to 1000ms if
> +	 * we do know the device is there.
> +	 */
> +	for (i = 1, j = 0; j < limit && !is_pcie_link_up(pcie, true);
> +	     j += i, i = i * 2)
> +		msleep(i + j > limit ? limit - j : i);
> +
> +	if (!is_pcie_link_up(pcie, false)) {
> +		dev_info(pcie->dev, "link down\n");
> +		return -ENODEV;
> +	}
> +
> +	for (i = 0; i < pcie->num_out_wins; i++)
> +		set_pcie_outbound_win(pcie, i, pcie->out_wins[i].cpu_addr,
> +				      pcie->out_wins[i].pci_addr,
> +				      pcie->out_wins[i].size);
> +
> +	/* For config space accesses on the RC, show the right class for
> +	 * a PCI-PCI bridge
> +	 */
> +	WR_FLD_RB(base, PCIE_RC_CFG_PRIV1_ID_VAL3, CLASS_CODE, 0x060400);
> +
> +	if (pcie->ssc) {
> +		ret = set_ssc(base);
> +		if (ret == 0)
> +			ssc_good = true;
> +		else
> +			dev_err(pcie->dev,
> +				"failed attempt to enter ssc mode\n");
> +	}
> +
> +	status = bcm_readl(base + PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL);
> +	neg_width = EXTRACT_FIELD(status, PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL,
> +				  NEG_LINK_WIDTH);
> +	neg_speed = EXTRACT_FIELD(status, PCIE_RC_CFG_PCIE_LINK_STATUS_CONTROL,
> +				  NEG_LINK_SPEED);
> +	dev_info(pcie->dev, "link up, %s Gbps x%u %s\n",
> +		 link_speed_to_str(neg_speed), neg_width,
> +		 ssc_good ? "(SSC)" : "(!SSC)");
> +
> +	/* Enable configuration request retry (see pci_scan_device()) */
> +	/* field RC_CRS_EN = 1 */
> +	WR_FLD(base, PCIE_RC_CFG_PCIE_ROOT_CAP_CONTROL, RC_CRS_EN, 1);

As long as you advertise CRS SV support, the PCI core should be
enabling it automatically; why do you need this here?

> +
> +	/* PCIE->SCB endian mode for BAR */
> +	/* field ENDIAN_MODE_BAR2 = DATA_ENDIAN */
> +	WR_FLD_RB(base, PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1,
> +		  ENDIAN_MODE_BAR2, DATA_ENDIAN);
> +
> +	/* Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1
> +	 * is enabled =>  setting the CLKREQ_DEBUG_ENABLE field to 1.
> +	 */
> +	WR_FLD_RB(base, PCIE_MISC_HARD_PCIE_HARD_DEBUG, CLKREQ_DEBUG_ENABLE, 1);
> +
> +	pcie->bridge_setup_done = true;
> +
> +	return 0;
> +}
> +
> +static void enter_l23(struct brcm_pcie *pcie)
> +{
> +	void __iomem *base = pcie->base;
> +	int tries, l23;
> +
> +	/* assert request for L23 */
> +	WR_FLD_RB(base, PCIE_MISC_PCIE_CTRL, PCIE_L23_REQUEST, 1);
> +	/* poll L23 status */
> +	for (tries = 0, l23 = 0; tries < 1000 && !l23; tries++)
> +		l23 = RD_FLD(base, PCIE_MISC_PCIE_STATUS, PCIE_LINK_IN_L23);
> +	if (!l23)
> +		dev_err(pcie->dev, "failed to enter L23\n");
> +}
> +
> +static void turn_off(struct brcm_pcie *pcie)
> +{
> +	void __iomem *base = pcie->base;
> +
> +	if (is_pcie_link_up(pcie, true))
> +		enter_l23(pcie);
> +	/* Reset endpoint device */
> +	brcm_pcie_perst_set(pcie, 1);
> +	/* deassert request for L23 in case it was asserted */
> +	WR_FLD_RB(base, PCIE_MISC_PCIE_CTRL, PCIE_L23_REQUEST, 0);
> +	/* SERDES_IDDQ = 1 */
> +	WR_FLD_RB(base, PCIE_MISC_HARD_PCIE_HARD_DEBUG, SERDES_IDDQ, 1);
> +	/* Shutdown PCIe bridge */
> +	brcm_pcie_bridge_sw_init_set(pcie, 1);
> +}
> +
> +static int brcm_pcie_suspend(struct device *dev)
> +{
> +	struct brcm_pcie *pcie = dev_get_drvdata(dev);
> +
> +	if (!pcie->bridge_setup_done)
> +		return 0;
> +
> +	turn_off(pcie);
> +	clk_disable_unprepare(pcie->clk);
> +	set_regulators(pcie, false);
> +	pcie->suspended = true;
> +
> +	return 0;
> +}
> +
> +static int brcm_pcie_resume(struct device *dev)
> +{
> +	struct brcm_pcie *pcie = dev_get_drvdata(dev);
> +	void __iomem *base;
> +	int ret;
> +
> +	if (!pcie->bridge_setup_done)
> +		return 0;
> +
> +	base = pcie->base;
> +	set_regulators(pcie, true);
> +	clk_prepare_enable(pcie->clk);
> +
> +	/* Take bridge out of reset so we can access the SERDES reg */
> +	brcm_pcie_bridge_sw_init_set(pcie, 0);
> +
> +	/* SERDES_IDDQ = 0 */
> +	WR_FLD_RB(base, PCIE_MISC_HARD_PCIE_HARD_DEBUG, SERDES_IDDQ, 0);
> +	/* wait for serdes to be stable */
> +	usleep_range(100, 200);
> +
> +	brcm_pcie_setup_prep(pcie);
> +
> +	ret = brcm_pcie_setup_bridge(pcie);
> +	if (ret)
> +		return ret;
> +
> +	pcie->suspended = false;
> +
> +	return 0;
> +}
> +
> +/* Configuration space read/write support */
> +static int cfg_index(int busnr, int devfn, int reg)
> +{
> +	return ((PCI_SLOT(devfn) & 0x1f) << PCI_SLOT_SHIFT)
> +		| ((PCI_FUNC(devfn) & 0x07) << PCI_FUNC_SHIFT)
> +		| (busnr << PCI_BUSNUM_SHIFT)
> +		| (reg & ~3);
> +}
> +
> +static void __iomem *brcm_pci_map_cfg(struct pci_bus *bus, unsigned int devfn,
> +				      int where)
> +{
> +	struct brcm_pcie *pcie = bus->sysdata;
> +	void __iomem *base = pcie->base;
> +	bool rc_access = pci_is_root_bus(bus);
> +	int idx;
> +
> +	if (!is_pcie_link_up(pcie, true))
> +		return NULL;

Why do you need this test?  It makes this racy because the link could
go down after you call is_pcie_link_up() but before you perform the
config access.

> +	base = pcie->base;
> +	idx = cfg_index(bus->number, devfn, where);
> +
> +	bcm_writel(idx, pcie->base + IDX_ADDR(pcie));
> +
> +	if (rc_access) {
> +		if (PCI_SLOT(devfn))
> +			return NULL;
> +		return base + (where & ~3);
> +	}

Many drivers have a similar pattern.  Please implement this in a
similar way, e.g., see dw_pcie_valid_device(),
altera_pcie_valid_device(), rockchip_pcie_valid_device(), etc.

> +	return pcie->base + DATA_ADDR(pcie);
> +}
> +
> +static void __attribute__((__section__("pci_fixup_early")))
> +brcm_pcibios_fixup(struct pci_dev *dev)
> +{
> +	struct brcm_pcie *pcie = dev->bus->sysdata;
> +	u8 slot = PCI_SLOT(dev->devfn);
> +
> +	dev_info(pcie->dev,
> +		 "found device %04x:%04x on bus %d (%s), slot %d (irq %d)\n",
> +		 dev->vendor, dev->device, dev->bus->number, pcie->name,
> +		 slot, of_irq_parse_and_map_pci(dev, slot, 1));
> +}
> +DECLARE_PCI_FIXUP_EARLY(PCI_ANY_ID, PCI_ANY_ID, brcm_pcibios_fixup);

This looks like debug code that should be removed.

> +
> +static const struct of_device_id brcm_pci_match[] = {
> +	{ .compatible = "brcm,bcm7425-pcie", .data = &bcm7425_cfg },
> +	{ .compatible = "brcm,bcm7435-pcie", .data = &bcm7435_cfg },
> +	{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
> +	{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, brcm_pci_match);
> +
> +static void _brcm_pcie_remove(struct brcm_pcie *pcie)
> +{
> +	turn_off(pcie);
> +	clk_disable_unprepare(pcie->clk);
> +	clk_put(pcie->clk);
> +	set_regulators(pcie, false);
> +	brcm_pcie_remove_controller(pcie);
> +}
> +
> +static int brcm_pcie_probe(struct platform_device *pdev)
> +{
> +	struct device_node *dn = pdev->dev.of_node;
> +	struct property *pp;
> +	const struct of_device_id *of_id;
> +	const struct pcie_cfg_data *data;
> +	int ret;
> +	struct brcm_pcie *pcie;
> +	struct resource *res;
> +	void __iomem *base;
> +	u32 tmp;
> +	struct brcm_dev_pwr_supply *supply;
> +	struct pci_host_bridge *bridge;
> +	struct pci_bus *child;
> +	u32 domain;
> +
> +	bridge = devm_pci_alloc_host_bridge(&pdev->dev, sizeof(*pcie));
> +	if (!bridge)
> +		return -ENOMEM;
> +
> +	pcie = pci_host_bridge_priv(bridge);
> +	INIT_LIST_HEAD(&pcie->resources);
> +
> +	of_id = of_match_node(brcm_pci_match, dn);
> +	if (!of_id) {
> +		pr_err("failed to look up compatible string\n");

Please use dev_err(), etc. for every single log message so we can
associate log messages with a device.

> +		return -EINVAL;
> +	}
> +
> +	if (of_property_read_u32(dn, "dma-ranges", &tmp) == 0) {
> +		pr_err("cannot yet handle dma-ranges\n");
> +		return -EINVAL;
> +	}
> +
> +	data = of_id->data;
> +	pcie->reg_offsets = data->offsets;
> +	pcie->reg_field_info = data->reg_field_info;
> +	pcie->type = data->type;
> +	pcie->dn = dn;
> +	pcie->dev = &pdev->dev;
> +
> +	if (of_property_read_u32(dn, "linux,pci-domain", &domain) == 0) {
> +		pcie->id = (int)domain;
> +	} else {
> +		dev_err(pcie->dev, "linux,pci-domain prop missing\n");
> +		return -EINVAL;
> +	}

You should not need this.  This should happen automatically via
of_get_pci_domain_nr() if you have things set up correctly.

> +
> +	INIT_LIST_HEAD(&pcie->pwr_supplies);
> +	for_each_property_of_node(dn, pp) {
> +		const int n = strlen(pp->name);
> +
> +		if (n < 7)
> +			continue;
> +		if (strncmp(pp->name + n - 7, "-supply", 7))
> +			continue;
> +		if (n > sizeof(supply->name) - 1) {
> +			dev_err(&pdev->dev, "prop supply name %s too long\n",
> +				pp->name);
> +			continue;
> +		}
> +		supply = devm_kzalloc(&pdev->dev, sizeof(*supply), GFP_KERNEL);
> +		if (!supply)
> +			return -ENOMEM;
> +		strcpy(supply->name, pp->name);
> +		supply->name[n - 7] = 0; /* remove "-supply" */
> +		supply->regulator = devm_regulator_get(&pdev->dev, supply->name);
> +
> +		if (IS_ERR(supply->regulator)) {
> +			dev_err(&pdev->dev, "Unable to get %s, err=%d\n",
> +				pp->name, (int)PTR_ERR(supply->regulator));
> +			continue;
> +		}
> +		list_add_tail(&supply->node, &pcie->pwr_supplies);
> +	}
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!res)
> +		return -EINVAL;
> +
> +	base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(base))
> +		return PTR_ERR(base);
> +
> +	pcie->clk = of_clk_get_by_name(dn, "sw_pcie");
> +	if (IS_ERR(pcie->clk)) {
> +		dev_err(&pdev->dev, "could not get clock\n");
> +		pcie->clk = NULL;
> +	}
> +	pcie->base = base;
> +
> +	ret = of_pci_get_max_link_speed(dn);
> +	pcie->gen = (ret < 0) ? 0 : ret;
> +
> +	pcie->ssc = of_property_read_bool(dn, "brcm,ssc");
> +
> +	ret = irq_of_parse_and_map(pdev->dev.of_node, 0);
> +	if (ret == 0)
> +		/* keep going, as we don't use this intr yet */
> +		dev_warn(pcie->dev, "cannot get pcie interrupt\n");
> +	else
> +		pcie->irq = ret;
> +
> +	ret = brcm_parse_ranges(pcie);
> +	if (ret)
> +		return ret;
> +
> +	ret = clk_prepare_enable(pcie->clk);
> +	if (ret) {
> +		dev_err(&pdev->dev, "could not enable clock\n");
> +		return ret;
> +	}
> +
> +	ret = brcm_pcie_add_controller(pcie);
> +	if (ret)
> +		return ret;
> +
> +	set_regulators(pcie, true);
> +	brcm_pcie_setup_prep(pcie);
> +	ret = brcm_pcie_setup_bridge(pcie);
> +	if (ret)
> +		goto fail;
> +
> +	list_splice_init(&pcie->resources, &bridge->windows);
> +	bridge->dev.parent = &pdev->dev;
> +	bridge->busnr = 0;
> +	bridge->ops = &brcm_pci_ops;
> +	bridge->sysdata = pcie;
> +	bridge->map_irq = of_irq_parse_and_map_pci;
> +	bridge->swizzle_irq = pci_common_swizzle;
> +
> +	ret = pci_scan_root_bus_bridge(bridge);
> +	if (ret < 0) {
> +		dev_err(pcie->dev, "Scanning root bridge failed");
> +		goto fail;
> +	}
> +
> +	pci_assign_unassigned_bus_resources(bridge->bus);
> +	list_for_each_entry(child, &bridge->bus->children, node)
> +		pcie_bus_configure_settings(child);
> +	pci_bus_add_devices(bridge->bus);
> +	platform_set_drvdata(pdev, pcie);
> +	pcie->root_bus = bridge->bus;

General comment, can you scan some of the other drivers in
drivers/pci/host/ and follow a similar style?  Similar structure,
similar function names, similar variable names, etc.  It makes it much
easier to maintain this whole collection.

> +	return 0;
> +
> +fail:
> +	_brcm_pcie_remove(pcie);
> +	return ret;
> +}
> +
> +static int brcm_pcie_remove(struct platform_device *pdev)
> +{
> +	struct brcm_pcie *pcie = platform_get_drvdata(pdev);
> +
> +	pci_stop_root_bus(pcie->root_bus);
> +	pci_remove_root_bus(pcie->root_bus);
> +	_brcm_pcie_remove(pcie);
> +
> +	return 0;
> +}
> +
> +static const struct dev_pm_ops brcm_pcie_pm_ops = {
> +	.suspend_noirq = brcm_pcie_suspend,
> +	.resume_noirq = brcm_pcie_resume,
> +};
> +
> +static struct platform_driver __refdata brcm_pci_driver = {
> +	.probe = brcm_pcie_probe,
> +	.remove = brcm_pcie_remove,
> +	.driver = {
> +		.name = "brcm-pci",
> +		.owner = THIS_MODULE,
> +		.of_match_table = brcm_pci_match,
> +		.pm = &brcm_pcie_pm_ops,
> +	},
> +};
> +
> +module_platform_driver(brcm_pci_driver);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_DESCRIPTION("Broadcom STB PCIE RC driver");
> +MODULE_AUTHOR("Broadcom");
> diff --git a/drivers/pci/host/pci-brcmstb.h b/drivers/pci/host/pci-brcmstb.h
> new file mode 100644
> index 0000000..86f9cd1
> --- /dev/null
> +++ b/drivers/pci/host/pci-brcmstb.h
> @@ -0,0 +1,33 @@
> +#ifndef __BRCMSTB_PCI_H
> +#define __BRCMSTB_PCI_H
> +
> +/*
> + * Copyright (C) 2015 - 2017 Broadcom
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#define BRCM_PCIE_NAME_SIZE		8
> +#define BRCM_INT_PCI_MSI_NR		32
> +#define BRCM_PCIE_HW_REV_33		0x0303
> +
> +/* Broadcom PCIE Offsets */
> +#define PCIE_INTR2_CPU_BASE		0x4300
> +
> +#if defined(CONFIG_MIPS)
> +/* Broadcom MIPs HW implicitly does the swapping if necessary */
> +#define bcm_readl(a)		__raw_readl(a)
> +#define bcm_writel(d, a)	__raw_writel(d, a)
> +#else
> +#define bcm_readl(a)		readl(a)
> +#define bcm_writel(d, a)	writel(d, a)
> +#endif
> +
> +#endif /* __BRCMSTB_PCI_H */
> -- 
> 1.9.0.138.g2de3478
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel


[Index of Archives]     [Linux MIPS Home]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Linux]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux