On Fri, Jun 16, 2017 at 02:37:02PM -0700, Florian Fainelli wrote:
> Document the different nodes required for supporting S2/S3/S5 suspend
> states on MIPS-based Broadcom STB SoCs.
>
> Signed-off-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
> ---
> .../devicetree/bindings/mips/brcm/soc.txt | 77 ++++++++++++++++++++++
> 1 file changed, 77 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt
> index e4e1cd91fb1f..f7413168d938 100644
> --- a/Documentation/devicetree/bindings/mips/brcm/soc.txt
> +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt
> @@ -11,3 +11,80 @@ Required properties:
>
> The experimental -viper variants are for running Linux on the 3384's
> BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor.
> +
> +Power management
> +----------------
> +
> +For power management (particularly, S2/S3/S5 system suspend), the following SoC
> +components are needed:
> +
> += Always-On control block (AON CTRL)
> +
> +This hardware provides control registers for the "always-on" (even in low-power
> +modes) hardware, such as the Power Management State Machine (PMSM).
> +
> +Required properties:
> +- compatible : should contain "brcm,brcmstb-aon-ctrl"
Exact same block on all SoCs?
> +- reg : the register start and length for the AON CTRL block
> +
> +Example:
> +
> +aon-ctrl@410000 {
syscon@...
> + compatible = "brcm,brcmstb-aon-ctrl";
> + reg = <0x410000 0x400>;
> +};
> +
> += Memory controllers
> +
> +A Broadcom STB SoC typically has a number of independent memory controllers,
> +each of which may have several associated hardware blocks, which are versioned
> +independently (control registers, DDR PHYs, etc.). One might consider
> +describing these controllers as a parent "memory controllers" block, which
> +contains N sub-nodes (one for each controller in the system), each of which is
> +associated with a number of hardware register resources (e.g., its PHY). See
> +the example device tree snippet below.
What example?
> +
> +== MEMC (MEMory Controller)
> +
> +Represents a single memory controller instance.
> +
> +Required properties:
> +- compatible : should contain "brcm,brcmstb-memc" and "simple-bus"
No registers for the controller?
> +
> +Should contain subnodes for any of the following relevant hardware resources:
> +
> +== DDR PHY control
> +
> +Control registers for this memory controller's DDR PHY.
> +
> +Required properties:
> +- compatible : should contain one of these
> + "brcm,brcmstb-ddr-phy-v64.5"
> + "brcm,brcmstb-ddr-phy"
> +
> +- reg : the DDR PHY register range
> +
> +== MEMC Arbiter
> +
> +The memory controller arbiter is responsible for memory clients allocation
> +(bandwidth, priorities etc.) and needs to have its contents restored during
> +deep sleep states (S3).
> +
> +Required properties:
> +
> +- compatible : should contain one of these
> + "brcm,brcmstb-memc-arb-v10.0.0.0"
> + "brcm,brcmstb-memc-arb"
> +
> +- reg : the DDR Arbiter register range
> +
> +== Timers
> +
> +The Broadcom STB chips contain a timer block with several general purpose
> +timers that can be used.
> +
> +Required properties:
> +
> +- compatible : should contain "brcm,brcmstb-timers"
> +- reg : the timers register range
> +
> --
> 2.9.3
>
