Re: [PATCH 05/13] MIPS: jz4740: DTS: Add node for the jz4740-pinctrl driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jan 18, 2017 at 12:14 AM, Paul Cercueil <paul@xxxxxxxxxxxxxxx> wrote:

> For a description of the devicetree node, please read
> Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
>
> Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>

(...)

> +       pinctrl: ingenic-pinctrl@10010000 {
> +               compatible = "ingenic,jz4740-pinctrl";
> +               #address-cells = <1>;
> +               #size-cells = <1>;
> +               ranges;
> +
> +               gpio-chips {
> +                       #address-cells = <1>;
> +                       #size-cells = <1>;
> +                       ranges;
> +
> +                       gpa: gpa {
> +                               reg = <0x10010000 0x100>;
> +
> +                               gpio-controller;
> +                               #gpio-cells = <2>;
> +
> +                               interrupt-controller;
> +                               #interrupt-cells = <2>;
> +
> +                               interrupt-parent = <&intc>;
> +                               interrupts = <28>;
> +
> +                               ingenic,pull-ups = <0xffffffff>;
> +                       };
> +
> +                       gpb: gpb {
> +                               reg = <0x10010100 0x100>;
> +
> +                               gpio-controller;
> +                               #gpio-cells = <2>;
> +
> +                               interrupt-controller;
> +                               #interrupt-cells = <2>;
> +
> +                               interrupt-parent = <&intc>;
> +                               interrupts = <27>;
> +
> +                               ingenic,pull-ups = <0xffffffff>;
> +                       };
> +
> +                       gpc: gpc {
> +                               reg = <0x10010200 0x100>;
> +
> +                               gpio-controller;
> +                               #gpio-cells = <2>;
> +
> +                               interrupt-controller;
> +                               #interrupt-cells = <2>;
> +
> +                               interrupt-parent = <&intc>;
> +                               interrupts = <26>;
> +
> +                               ingenic,pull-ups = <0xffffffff>;
> +                       };
> +
> +                       gpd: gpd {
> +                               reg = <0x10010300 0x100>;
> +
> +                               gpio-controller;
> +                               #gpio-cells = <2>;
> +
> +                               interrupt-controller;
> +                               #interrupt-cells = <2>;
> +
> +                               interrupt-parent = <&intc>;
> +                               interrupts = <25>;
> +
> +                               ingenic,pull-ups = <0xdfffffff>;
> +                       };
> +               };

Just pull all these down two levels and make them one device
each instead of having them inside the pin controller node
like this.

Then make a pin controller node separately, it can reference the
pin controller by phandles if necessary, and use the standard
gpio-ranges property to cross make GPIO and pin control.

It seems you driver is similar to for example the
drivers/pinctrl/nomadik/* pin controller.

Look in arch/arm/boot/dts/ste-dbx500.dtsi for examples,
NB: I'm not fully using standard bindings in it, because they
were not invented at the time.

Yours,
Linus Walleij




[Index of Archives]     [Linux MIPS Home]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Linux]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux