On Fri, Jan 13, 2017 at 08:44:47AM +0100, Marcin Nowakowski wrote:
> If a watchpoint is hit when in kernel mode it is possible for the system
> to end up in an infinite loop processing the watchpoint. This can happen
> if a user sets a watchpoint in the kernel addess space (which is
> possible in certain EVA configurations) or if a user sets a watchpoint
> in a user area accessed directly by the kernel (eg. a user buffer
> accessed via a syscall).
>
> To prevent the infinite loop ensure that the watchpoint was hit in
> userspace, and clear the watchpoint registers otherwise.
>
> As this change could mean that a watchpoint is not hit when it should be
> (when returning to the interrupted traced task on exception exit), the
> resume_userspace path needs to be extended to conditionally restore the
> watchpoint configuration. If a task switch occurs when returning to
> userspace, the watchpoints will be restored in a typical way in the
> switch_to() handler.
>
> Signed-off-by: Marcin Nowakowski <marcin.nowakowski@xxxxxxxxxx>
> ---
> arch/mips/kernel/entry.S | 9 ++++++++-
> arch/mips/kernel/traps.c | 2 +-
> 2 files changed, 9 insertions(+), 2 deletions(-)
>
> diff --git a/arch/mips/kernel/entry.S b/arch/mips/kernel/entry.S
> index ef69a64..b15a9a9 100644
> --- a/arch/mips/kernel/entry.S
> +++ b/arch/mips/kernel/entry.S
> @@ -55,7 +55,14 @@ resume_userspace:
> LONG_L a2, TI_FLAGS($28) # current->work
> andi t0, a2, _TIF_WORK_MASK # (ignoring syscall_trace)
> bnez t0, work_pending
> - j restore_all
> +#ifdef CONFIG_HARDWARE_WATCHPOINTS
> + li t0, _TIF_LOAD_WATCH
> + and t0, a2, t0
> + beqz t0, 1f
> + PTR_L a0, TI_TASK($28)
> + jal mips_install_watch_registers
> +#endif
Perhaps this should also be conditional upon EVA, otherwise the return
to userland path would get unnecessarily slower whenever watchpoints are
enabled.
TBH my worry with this general approach is that it permits userland to
mess with kernel assumptions in quite controlled and unexpected ways.
For example, it allows userland to inject temporary enabling of
interrupts at any point, e.g. in a spin_lock_irq() critical section
somewhere.
Perhaps that specific case can be worked around by having do_watch leave
interrupts disabled if they were already disabled when the exception was
taken. resume_kernel won't call preempt_schedule_irq() if IRQs are
disabled in the context being restored.
The other issue is I think it only really considers instruction watches
(hardware breakpoints). What about if userland put a data watchpoint on
a kernel stack address that gets hit in do_watch()'s prologue (i.e.
after EXL=0)? That can't be placed in a dedicated section, and would be
tricky to specifically exclude (would fork result in a new kernel stack
pointer and also preserve watch points?), and doing so would potentially
leak the process' kernel stack pointer too (regardless of KASLR),
presumably a valuable target for an exploit.
Cheers
James
> +1: j restore_all
>
> #ifdef CONFIG_PREEMPT
> resume_kernel:
> diff --git a/arch/mips/kernel/traps.c b/arch/mips/kernel/traps.c
> index b86ce85..d92169e 100644
> --- a/arch/mips/kernel/traps.c
> +++ b/arch/mips/kernel/traps.c
> @@ -1527,7 +1527,7 @@ asmlinkage void do_watch(struct pt_regs *regs)
> * their values and send SIGTRAP. Otherwise another thread
> * left the registers set, clear them and continue.
> */
> - if (test_tsk_thread_flag(current, TIF_LOAD_WATCH)) {
> + if (user_mode(regs) && test_tsk_thread_flag(current, TIF_LOAD_WATCH)) {
> mips_read_watch_registers();
> local_irq_enable();
> force_sig_info(SIGTRAP, &info, current);
> --
> 2.7.4
>
Attachment:
signature.asc
Description: Digital signature
