On 19/04/16 15:41, Boris Brezillon wrote:
> On Tue, 19 Apr 2016 15:30:39 +0300
> Roger Quadros <rogerq@xxxxxx> wrote:
>
>> On 19/04/16 14:22, Boris Brezillon wrote:
>>> Hi Roger,
>>>
>>> On Tue, 19 Apr 2016 13:28:50 +0300
>>> Roger Quadros <rogerq@xxxxxx> wrote:
>>>
>>>>> @@ -1921,6 +1927,9 @@ static int omap_nand_probe(struct platform_device *pdev)
>>>>> nand_chip->ecc.correct = omap_correct_data;
>>>>> mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
>>>>> oobbytes_per_step = nand_chip->ecc.bytes;
>>>>> +
>>>>> + if (nand_chip->options & NAND_BUSWIDTH_16)
>>>>> + min_oobbytes = 1;
>>>>
>>>> Shouldn't this have been
>>>> if (!(nand_chip->options & NAND_BUSWIDTH_16)
>>>> min_oobbytes = 1;
>>>> ?
>>>
>>> Yep.
>>>
>>>>
>>>>> break;
>>>>>
>>>>> case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
>>>>> @@ -2038,10 +2047,8 @@ static int omap_nand_probe(struct platform_device *pdev)
>>>>> }
>>>>>
>>>>> /* check if NAND device's OOB is enough to store ECC signatures */
>>>>> - min_oobbytes = (oobbytes_per_step *
>>>>> - (mtd->writesize / nand_chip->ecc.size)) +
>>>>> - (nand_chip->options & NAND_BUSWIDTH_16 ?
>>>>> - BADBLOCK_MARKER_LENGTH : 1);
>>>>> + min_oobbytes += (oobbytes_per_step *
>>>>> + (mtd->writesize / nand_chip->ecc.size));
>>>>> if (mtd->oobsize < min_oobbytes) {
>>>>> dev_err(&info->pdev->dev,
>>>>> "not enough OOB bytes required = %d, available=%d\n",
>>>>>
>>>>
>>>> After the above changes BCH with HW ECC worked fine but BCH with SW ECC still failed.
>>>> I had to fix it up with the below patch. This is mainly because chip->ecc.steps wasn't
>>>> yet initialized before calling nand_bch_init().
>>>>
>>>> After the below patch it worked fine with bch4 (hw & sw), bch8 (hw & sw) and ham1.
>>>> I couldn't yet verify bch16 though.
>>>
>>
>> I just verified that bch16 works as well.
>>
>>> Thanks for the fix, but I'd prefer fixing the bug for all soft BCH
>>> users.
>>>
>>> Could you try this patch?
>>
>> I tried your patch and it worked fine.
>
> Thanks, I'll provide a reworked nand/next branch soon.
> BTW, is there anything to fix in my merge commit (the commit merging
> your GPMC/OMAP changes in nand/next)?
>
I just replied in the other thread that the conflict resolution is fine.
>> You will still need the below change to omap2.c
>>
>> --
>> cheers,
>> -roger
>>
>> diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
>> index 0abfba6..33c8fde 100644
>> --- a/drivers/mtd/nand/omap2.c
>> +++ b/drivers/mtd/nand/omap2.c
>> @@ -1715,7 +1715,7 @@ static int omap_sw_ooblayout_free(struct mtd_info *mtd, int section,
>> struct nand_chip *chip = mtd_to_nand(mtd);
>> int off = BADBLOCK_MARKER_LENGTH;
>>
>> - if (section)
>> + if (section >= chip->ecc.steps)
>> return -ERANGE;
>
> Sorry but I don't get why we need that one. Don't we have a single
> oobfree section starting at the end of the ECC sections?
>
>
You are right. Nothing needs to be changed there then. Thanks :)
cheers,
-roger
