From: Aleksey Makarov <aleksey.makarov@xxxxxxxxxxxxxxxxxx>
Add Device Tree binding document for Octeon MMC controller. The driver
is in a following patch.
The MMC controller can be connected to up to 4 "slots" which may be
eMMC, MMC or SD card devices. As there is a single controller, each
available slot is represented as a child node of the controller.
This is a similar concept to the atmel-mci driver.
Tested-by: Aaro Koskinen <aaro.koskinen@xxxxxx>
Signed-off-by: Chandrakala Chavva <cchavva@xxxxxxxxxxxxxxxxxx>
Signed-off-by: David Daney <david.daney@xxxxxxxxxx>
Signed-off-by: Aleksey Makarov <aleksey.makarov@xxxxxxxxxx>
Signed-off-by: Leonid Rosenboim <lrosenboim@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Peter Swain <pswain@xxxxxxxxxx>
Signed-off-by: Aaron Williams <aaron.williams@xxxxxxxxxx>
Signed-off-by: Matt Redfearn <matt.redfearn@xxxxxxxxxx>
---
Changes since v6:
- Split up patch
- Moved device tree fixup to platform code
---
.../devicetree/bindings/mmc/octeon-mmc.txt | 80 ++++++++++++++++++++++
1 file changed, 80 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/octeon-mmc.txt
diff --git a/Documentation/devicetree/bindings/mmc/octeon-mmc.txt b/Documentation/devicetree/bindings/mmc/octeon-mmc.txt
new file mode 100644
index 000000000000..a1b20753172f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/octeon-mmc.txt
@@ -0,0 +1,80 @@
+* OCTEON SD/MMC Host Controller
+
+This controller is present on some members of the Cavium OCTEON SoC
+family, provide an interface for eMMC, MMC and SD devices. There is a
+single controller that may have several "slots" connected. These
+slots appear as children of the main controller node.
+The DMA engine is an integral part of the controller block.
+
+1) MMC node
+
+Required properties:
+- compatible : Should be "cavium,octeon-6130-mmc" or "cavium,octeon-7890-mmc"
+- reg : Two entries:
+ 1) The base address of the MMC controller register bank.
+ 2) The base address of the MMC DMA engine register bank.
+- interrupts :
+ For "cavium,octeon-6130-mmc": two entries:
+ 1) The MMC controller interrupt line.
+ 2) The MMC DMA engine interrupt line.
+ For "cavium,octeon-7890-mmc": nine entries:
+ 1) The next block transfer of a multiblock transfer has completed (BUF_DONE)
+ 2) Operation completed successfully (CMD_DONE).
+ 3) DMA transfer completed successfully (DMA_DONE).
+ 4) Operation encountered an error (CMD_ERR).
+ 5) DMA transfer encountered an error (DMA_ERR).
+ 6) Switch operation completed successfully (SWITCH_DONE).
+ 7) Switch operation encountered an error (SWITCH_ERR).
+ 8) Internal DMA engine request completion interrupt (DONE).
+ 9) Internal DMA FIFO underflow (FIFO).
+- #address-cells : Must be <1>
+- #size-cells : Must be <0>
+
+The node contains child nodes for each slot that the platform uses.
+
+Example:
+mmc@1180000002000 {
+ compatible = "cavium,octeon-6130-mmc";
+ reg = <0x11800 0x00002000 0x0 0x100>,
+ <0x11800 0x00000168 0x0 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* EMM irq, DMA irq */
+ interrupts = <1 19>, <0 63>;
+
+ [ child node definitions...]
+};
+
+
+2) Slot nodes
+Properties in mmc.txt apply to each slot node that the platform uses.
+
+Required properties:
+- reg : The slot number.
+
+Optional properties:
+- cavium,cmd-clk-skew : the amount of delay (in pS) past the clock edge
+ to sample the command pin.
+- cavium,dat-clk-skew : the amount of delay (in pS) past the clock edge
+ to sample the data pin.
+
+Example:
+ mmc@1180000002000 {
+ compatible = "cavium,octeon-6130-mmc";
+ reg = <0x11800 0x00002000 0x0 0x100>,
+ <0x11800 0x00000168 0x0 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* EMM irq, DMA irq */
+ interrupts = <1 19>, <0 63>;
+
+ /* The board only has a single MMC slot */
+ mmc-slot@0 {
+ reg = <0>;
+ max-frequency = <20000000>;
+ bus-width = <8>;
+ vmmc-supply = <®_vmmc3>;
+ cd-gpios = <&gpio 9 0>;
+ wp-gpios = <&gpio 10 0>;
+ };
+ };
--
2.5.0
