[PATCH 1/2] MIPS: bmips: Add bcm63168-l1 interrupt controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add device tree binding for the BCM63168 interrupt controller.

This controller is similar to the SMP-capable BCM7038 and
the BCM3380 but with packed interrupt registers.

Signed-off-by: Simon Arlott <simon@xxxxxxxxxxx>
---
 .../interrupt-controller/brcm,bcm63168-l1-intc.txt | 57 ++++++++++++++++++++++
 1 file changed, 57 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt
new file mode 100644
index 0000000..636a6db
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt
@@ -0,0 +1,57 @@
+Broadcom BCM63168-style Level 1 interrupt controller
+
+This block is a first level interrupt controller that is typically connected
+directly to one of the HW INT lines on each CPU.
+
+Key elements of the hardware design include:
+
+- 64 or 128 incoming level IRQ lines
+
+- Most onchip peripherals are wired directly to an L1 input
+
+- A separate instance of the register set for each CPU, allowing individual
+  peripheral IRQs to be routed to any CPU
+
+- Contains one or more enable/status word pairs per CPU
+
+- No atomic set/clear operations
+
+- No polarity/level/edge settings
+
+- No FIFO or priority encoder logic; software is expected to read all
+  2-4 status words to determine which IRQs are pending
+
+Required properties:
+
+- compatible: should be "brcm,bcm63168-l1-intc"
+- reg: specifies the base physical address and size of the registers;
+  the number of supported IRQs is inferred from the size argument
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+  this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+  node; valid values depend on the type of parent interrupt controller
+
+If multiple reg ranges and interrupt-parent entries are present on an SMP
+system, the driver will allow IRQ SMP affinity to be set up through the
+/proc/irq/ interface.  In the simplest possible configuration, only one
+reg range and one interrupt-parent is needed.
+
+The driver operates in native CPU endian by default, there is no support for
+specifying an alternative endianness.
+
+Example:
+
+periph_intc: periph_intc@10000000 {
+        compatible = "brcm,bcm63168-l1-intc";
+        reg = <0x10000020 0x20>,
+              <0x10000040 0x20>;
+
+        interrupt-controller;
+        #interrupt-cells = <1>;
+
+        interrupt-parent = <&cpu_intc>;
+        interrupts = <2>, <3>;
+};
-- 
2.1.4

-- 
Simon Arlott




[Index of Archives]     [Linux MIPS Home]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Linux]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux