From: Alex Smith <alex.smith@xxxxxxxxxx>
Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
and make use of them in the Ci20 device tree to add a node for the
board's NAND.
Note that since the pinctrl driver is not yet upstream, this includes
neither pin configuration nor busy/write-protect GPIO pins for the
NAND. Use of the NAND relies on the boot loader to have left the pins
configured in a usable state, which should be the case when booted
from the NAND.
Signed-off-by: Alex Smith <alex.smith@xxxxxxxxxx>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@xxxxxxxxxx>
Cc: David Woodhouse <dwmw2@xxxxxxxxxxxxx>
Cc: Brian Norris <computersforpeace@xxxxxxxxx>
Cc: Paul Burton <paul.burton@xxxxxxxxxx>
Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: linux-kernel@xxxxxxxxxxxxxxx
Cc: linux-mips@xxxxxxxxxxxxxx
Cc: Alex Smith <alex@xxxxxxxxxxxxxxxx>
Signed-off-by: Harvey Hunt <harvey.hunt@xxxxxxxxxx>
---
v6 -> v7:
- Add nand-ecc-mode to DT.
- Add nand-on-flash-bbt to DT.
v4 -> v5:
- New patch adding DT nodes for the NAND so that the driver can be
tested.
arch/mips/boot/dts/ingenic/ci20.dts | 54 ++++++++++++++++++++++++++++++++++
arch/mips/boot/dts/ingenic/jz4780.dtsi | 26 ++++++++++++++++
2 files changed, 80 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 9fcb9e7..453f1d3 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -42,3 +42,57 @@
&uart4 {
status = "okay";
};
+
+&nemc {
+ status = "okay";
+
+ nand: nand@1 {
+ compatible = "ingenic,jz4780-nand";
+ reg = <1 0 0x1000000>;
+
+ ingenic,nemc-tAS = <10>;
+ ingenic,nemc-tAH = <5>;
+ ingenic,nemc-tBP = <10>;
+ ingenic,nemc-tAW = <15>;
+ ingenic,nemc-tSTRV = <100>;
+
+ ingenic,bch-controller = <&bch>;
+ ingenic,ecc-size = <1024>;
+ ingenic,ecc-strength = <24>;
+
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ partition@0 {
+ label = "u-boot-spl";
+ reg = <0x0 0x0 0x0 0x800000>;
+ };
+
+ partition@0x800000 {
+ label = "u-boot";
+ reg = <0x0 0x800000 0x0 0x200000>;
+ };
+
+ partition@0xa00000 {
+ label = "u-boot-env";
+ reg = <0x0 0xa00000 0x0 0x200000>;
+ };
+
+ partition@0xc00000 {
+ label = "boot";
+ reg = <0x0 0xc00000 0x0 0x4000000>;
+ };
+
+ partition@0x8c00000 {
+ label = "system";
+ reg = <0x0 0x4c00000 0x1 0xfb400000>;
+ };
+ };
+};
+
+&bch {
+ status = "okay";
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index 65389f6..b868b42 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -108,4 +108,30 @@
status = "disabled";
};
+
+ nemc: nemc@13410000 {
+ compatible = "ingenic,jz4780-nemc";
+ reg = <0x13410000 0x10000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <1 0 0x1b000000 0x1000000
+ 2 0 0x1a000000 0x1000000
+ 3 0 0x19000000 0x1000000
+ 4 0 0x18000000 0x1000000
+ 5 0 0x17000000 0x1000000
+ 6 0 0x16000000 0x1000000>;
+
+ clocks = <&cgu JZ4780_CLK_NEMC>;
+
+ status = "disabled";
+ };
+
+ bch: bch@134d0000 {
+ compatible = "ingenic,jz4780-bch";
+ reg = <0x134d0000 0x10000>;
+
+ clocks = <&cgu JZ4780_CLK_BCH>;
+
+ status = "disabled";
+ };
};
--
2.6.0
