Introduce a driver suitable for use with the UARTs present in
Ingenic SoCs such as the JZ4740 & JZ4780. These are described as being
ns16550 compatible but aren't quite - they require the setting of an
extra bit in the FCR register to enable the UART module. The serial_out
implementation is the same as that in arch/mips/jz4740/serial.c - which
will shortly be removed.
Signed-off-by: Paul Burton <paul.burton@xxxxxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
Cc: Jiri Slaby <jslaby@xxxxxxx>
Cc: Lars-Peter Clausen <lars@xxxxxxxxxx>
Cc: linux-serial@xxxxxxxxxxxxxxx
---
Changes in v4:
- None.
Changes in v3:
- s/jz47xx/ingenic/ to reflect Ingenic's naming change for newer SoCs.
- Support JZ4775.
- Depend on SERIAL_8250_CONSOLE rather than selecting
SERIAL_CORE_CONSOLE.
- Read the UART clock for early consoles from the DT, using libfdt to
find the node for the fixed rate external clock which drives the UART
in all known Ingenic SoCs, rather than relying upon a hardcoded
definition for BASE_BAUD.
Changes in v2:
- Remove FSF address (ZubairLK).
- Select SERIAL_CORE_CONSOLE (ZubairLK).
---
drivers/tty/serial/8250/8250_ingenic.c | 261 +++++++++++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 9 ++
drivers/tty/serial/8250/Makefile | 3 +
3 files changed, 273 insertions(+)
create mode 100644 drivers/tty/serial/8250/8250_ingenic.c
diff --git a/drivers/tty/serial/8250/8250_ingenic.c b/drivers/tty/serial/8250/8250_ingenic.c
new file mode 100644
index 0000000..8eeadb4
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_ingenic.c
@@ -0,0 +1,261 @@
+/*
+ * Copyright (C) 2010 Lars-Peter Clausen <lars@xxxxxxxxxx>
+ * Copyright (C) 2015 Imagination Technologies
+ *
+ * Ingenic SoC UART support
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/io.h>
+#include <linux/libfdt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_fdt.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+
+struct ingenic_uart_data {
+ struct clk *clk_module;
+ struct clk *clk_baud;
+ int line;
+};
+
+#define UART_FCR_UME BIT(4)
+
+static struct earlycon_device *early_device;
+
+static uint8_t __init early_in(struct uart_port *port, int offset)
+{
+ return readl(port->membase + (offset << 2));
+}
+
+static void __init early_out(struct uart_port *port, int offset, uint8_t value)
+{
+ writel(value, port->membase + (offset << 2));
+}
+
+static void __init ingenic_early_console_putc(struct uart_port *port, int c)
+{
+ uint8_t lsr;
+
+ do {
+ lsr = early_in(port, UART_LSR);
+ } while ((lsr & UART_LSR_TEMT) == 0);
+
+ early_out(port, UART_TX, c);
+}
+
+static void __init ingenic_early_console_write(struct console *console,
+ const char *s, unsigned int count)
+{
+ uart_console_write(&early_device->port, s, count,
+ ingenic_early_console_putc);
+}
+
+static void __init ingenic_early_console_setup_clock(struct earlycon_device *dev)
+{
+ void *fdt = initial_boot_params;
+ const __be32 *prop;
+ int offset;
+
+ offset = fdt_path_offset(fdt, "/ext");
+ if (offset < 0)
+ return;
+
+ prop = fdt_getprop(fdt, offset, "clock-frequency", NULL);
+ if (!prop)
+ return;
+
+ dev->port.uartclk = be32_to_cpup(prop);
+}
+
+static int __init ingenic_early_console_setup(struct earlycon_device *dev,
+ const char *opt)
+{
+ struct uart_port *port = &dev->port;
+ unsigned int baud, divisor;
+
+ if (!dev->port.membase)
+ return -ENODEV;
+
+ ingenic_early_console_setup_clock(dev);
+
+ baud = dev->baud ?: 115200;
+ divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * baud);
+
+ early_out(port, UART_IER, 0);
+ early_out(port, UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8);
+ early_out(port, UART_DLL, 0);
+ early_out(port, UART_DLM, 0);
+ early_out(port, UART_LCR, UART_LCR_WLEN8);
+ early_out(port, UART_FCR, UART_FCR_UME | UART_FCR_CLEAR_XMIT |
+ UART_FCR_CLEAR_RCVR | UART_FCR_ENABLE_FIFO);
+ early_out(port, UART_MCR, UART_MCR_RTS | UART_MCR_DTR);
+
+ early_out(port, UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8);
+ early_out(port, UART_DLL, divisor & 0xff);
+ early_out(port, UART_DLM, (divisor >> 8) & 0xff);
+ early_out(port, UART_LCR, UART_LCR_WLEN8);
+
+ early_device = dev;
+ dev->con->write = ingenic_early_console_write;
+
+ return 0;
+}
+
+EARLYCON_DECLARE(jz4740_uart, ingenic_early_console_setup);
+OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart",
+ ingenic_early_console_setup);
+
+EARLYCON_DECLARE(jz4775_uart, ingenic_early_console_setup);
+OF_EARLYCON_DECLARE(jz4775_uart, "ingenic,jz4775-uart",
+ ingenic_early_console_setup);
+
+EARLYCON_DECLARE(jz4780_uart, ingenic_early_console_setup);
+OF_EARLYCON_DECLARE(jz4780_uart, "ingenic,jz4780-uart",
+ ingenic_early_console_setup);
+
+static void ingenic_uart_serial_out(struct uart_port *p, int offset, int value)
+{
+ switch (offset) {
+ case UART_FCR:
+ /* UART module enable */
+ value |= UART_FCR_UME;
+ break;
+
+ case UART_IER:
+ value |= (value & 0x4) << 2;
+ break;
+
+ default:
+ break;
+ }
+
+ writeb(value, p->membase + (offset << p->regshift));
+}
+
+static int ingenic_uart_probe(struct platform_device *pdev)
+{
+ struct uart_8250_port uart = {};
+ struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ struct ingenic_uart_data *data;
+ int err;
+
+ if (!regs || !irq) {
+ dev_err(&pdev->dev, "no registers/irq defined\n");
+ return -EINVAL;
+ }
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ spin_lock_init(&uart.port.lock);
+ uart.port.type = PORT_16550;
+ uart.port.flags = UPF_SKIP_TEST | UPF_IOREMAP | UPF_FIXED_TYPE;
+ uart.port.iotype = UPIO_MEM;
+ uart.port.mapbase = regs->start;
+ uart.port.regshift = 2;
+ uart.port.serial_out = ingenic_uart_serial_out;
+ uart.port.irq = irq->start;
+ uart.port.dev = &pdev->dev;
+
+ uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+ resource_size(regs));
+ if (!uart.port.membase)
+ return -ENOMEM;
+
+ data->clk_module = devm_clk_get(&pdev->dev, "module");
+ if (IS_ERR(data->clk_module)) {
+ err = PTR_ERR(data->clk_module);
+ if (err != -EPROBE_DEFER)
+ dev_err(&pdev->dev,
+ "unable to get module clock: %d\n", err);
+ return err;
+ }
+
+ data->clk_baud = devm_clk_get(&pdev->dev, "baud");
+ if (IS_ERR(data->clk_baud)) {
+ err = PTR_ERR(data->clk_baud);
+ if (err != -EPROBE_DEFER)
+ dev_err(&pdev->dev,
+ "unable to get baud clock: %d\n", err);
+ return err;
+ }
+
+ err = clk_prepare_enable(data->clk_module);
+ if (err) {
+ dev_err(&pdev->dev, "could not enable module clock: %d\n", err);
+ goto out;
+ }
+
+ err = clk_prepare_enable(data->clk_baud);
+ if (err) {
+ dev_err(&pdev->dev, "could not enable baud clock: %d\n", err);
+ goto out_disable_moduleclk;
+ }
+ uart.port.uartclk = clk_get_rate(data->clk_baud);
+
+ data->line = serial8250_register_8250_port(&uart);
+ if (data->line < 0) {
+ err = data->line;
+ goto out_disable_baudclk;
+ }
+
+ platform_set_drvdata(pdev, data);
+ return 0;
+
+out_disable_baudclk:
+ clk_disable_unprepare(data->clk_baud);
+out_disable_moduleclk:
+ clk_disable_unprepare(data->clk_module);
+out:
+ return err;
+}
+
+static int ingenic_uart_remove(struct platform_device *pdev)
+{
+ struct ingenic_uart_data *data = platform_get_drvdata(pdev);
+
+ serial8250_unregister_port(data->line);
+ clk_disable_unprepare(data->clk_module);
+ clk_disable_unprepare(data->clk_baud);
+ return 0;
+}
+
+static const struct of_device_id of_match[] = {
+ { .compatible = "ingenic,jz4740-uart" },
+ { .compatible = "ingenic,jz4775-uart" },
+ { .compatible = "ingenic,jz4780-uart" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, of_match);
+
+static struct platform_driver ingenic_uart_platform_driver = {
+ .driver = {
+ .name = "ingenic-uart",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match,
+ },
+ .probe = ingenic_uart_probe,
+ .remove = ingenic_uart_remove,
+};
+
+module_platform_driver(ingenic_uart_platform_driver);
+
+MODULE_AUTHOR("Paul Burton");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Ingenic SoC UART driver");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index c350703..43330ea 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -342,3 +342,12 @@ config SERIAL_8250_MT6577
help
If you have a Mediatek based board and want to use the
serial port, say Y to this option. If unsure, say N.
+
+config SERIAL_8250_INGENIC
+ bool "Support for Ingenic SoC serial ports"
+ depends on SERIAL_8250_CONSOLE && OF_FLATTREE
+ select LIBFDT
+ select SERIAL_EARLYCON
+ help
+ If you have a system using an Ingenic SoC and wish to make use of
+ its UARTs, say Y to this option. If unsure, say N.
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 31e7cdc..98fba26 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -23,3 +23,6 @@ obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o
obj-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o
obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o
+obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o
+
+CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt
--
2.3.5
