Move the register offsets and bit descriptions from the au1000.h header
to their only user, the au1000_eth.c driver.
Signed-off-by: Manuel Lauss <manuel.lauss@xxxxxxxxx>
Cc: netdev@xxxxxxxxxxxxxxx
---
arch/mips/include/asm/mach-au1x00/au1000.h | 126 -----------------------------
drivers/net/ethernet/amd/au1000_eth.c | 118 +++++++++++++++++++++++++++
2 files changed, 118 insertions(+), 126 deletions(-)
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index 60754fc..e506710 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -1003,132 +1003,6 @@ enum soc_au1200_ints {
#define SYS_RTCMATCH2 (SYS_BASE + 0x54)
#define SYS_RTCREAD (SYS_BASE + 0x58)
-/* Ethernet Controllers */
-
-/* 4 byte offsets from AU1000_ETH_BASE */
-#define MAC_CONTROL 0x0
-# define MAC_RX_ENABLE (1 << 2)
-# define MAC_TX_ENABLE (1 << 3)
-# define MAC_DEF_CHECK (1 << 5)
-# define MAC_SET_BL(X) (((X) & 0x3) << 6)
-# define MAC_AUTO_PAD (1 << 8)
-# define MAC_DISABLE_RETRY (1 << 10)
-# define MAC_DISABLE_BCAST (1 << 11)
-# define MAC_LATE_COL (1 << 12)
-# define MAC_HASH_MODE (1 << 13)
-# define MAC_HASH_ONLY (1 << 15)
-# define MAC_PASS_ALL (1 << 16)
-# define MAC_INVERSE_FILTER (1 << 17)
-# define MAC_PROMISCUOUS (1 << 18)
-# define MAC_PASS_ALL_MULTI (1 << 19)
-# define MAC_FULL_DUPLEX (1 << 20)
-# define MAC_NORMAL_MODE 0
-# define MAC_INT_LOOPBACK (1 << 21)
-# define MAC_EXT_LOOPBACK (1 << 22)
-# define MAC_DISABLE_RX_OWN (1 << 23)
-# define MAC_BIG_ENDIAN (1 << 30)
-# define MAC_RX_ALL (1 << 31)
-#define MAC_ADDRESS_HIGH 0x4
-#define MAC_ADDRESS_LOW 0x8
-#define MAC_MCAST_HIGH 0xC
-#define MAC_MCAST_LOW 0x10
-#define MAC_MII_CNTRL 0x14
-# define MAC_MII_BUSY (1 << 0)
-# define MAC_MII_READ 0
-# define MAC_MII_WRITE (1 << 1)
-# define MAC_SET_MII_SELECT_REG(X) (((X) & 0x1f) << 6)
-# define MAC_SET_MII_SELECT_PHY(X) (((X) & 0x1f) << 11)
-#define MAC_MII_DATA 0x18
-#define MAC_FLOW_CNTRL 0x1C
-# define MAC_FLOW_CNTRL_BUSY (1 << 0)
-# define MAC_FLOW_CNTRL_ENABLE (1 << 1)
-# define MAC_PASS_CONTROL (1 << 2)
-# define MAC_SET_PAUSE(X) (((X) & 0xffff) << 16)
-#define MAC_VLAN1_TAG 0x20
-#define MAC_VLAN2_TAG 0x24
-
-/* Ethernet Controller Enable */
-
-# define MAC_EN_CLOCK_ENABLE (1 << 0)
-# define MAC_EN_RESET0 (1 << 1)
-# define MAC_EN_TOSS (0 << 2)
-# define MAC_EN_CACHEABLE (1 << 3)
-# define MAC_EN_RESET1 (1 << 4)
-# define MAC_EN_RESET2 (1 << 5)
-# define MAC_DMA_RESET (1 << 6)
-
-/* Ethernet Controller DMA Channels */
-
-#define MAC0_TX_DMA_ADDR 0xB4004000
-#define MAC1_TX_DMA_ADDR 0xB4004200
-/* offsets from MAC_TX_RING_ADDR address */
-#define MAC_TX_BUFF0_STATUS 0x0
-# define TX_FRAME_ABORTED (1 << 0)
-# define TX_JAB_TIMEOUT (1 << 1)
-# define TX_NO_CARRIER (1 << 2)
-# define TX_LOSS_CARRIER (1 << 3)
-# define TX_EXC_DEF (1 << 4)
-# define TX_LATE_COLL_ABORT (1 << 5)
-# define TX_EXC_COLL (1 << 6)
-# define TX_UNDERRUN (1 << 7)
-# define TX_DEFERRED (1 << 8)
-# define TX_LATE_COLL (1 << 9)
-# define TX_COLL_CNT_MASK (0xF << 10)
-# define TX_PKT_RETRY (1 << 31)
-#define MAC_TX_BUFF0_ADDR 0x4
-# define TX_DMA_ENABLE (1 << 0)
-# define TX_T_DONE (1 << 1)
-# define TX_GET_DMA_BUFFER(X) (((X) >> 2) & 0x3)
-#define MAC_TX_BUFF0_LEN 0x8
-#define MAC_TX_BUFF1_STATUS 0x10
-#define MAC_TX_BUFF1_ADDR 0x14
-#define MAC_TX_BUFF1_LEN 0x18
-#define MAC_TX_BUFF2_STATUS 0x20
-#define MAC_TX_BUFF2_ADDR 0x24
-#define MAC_TX_BUFF2_LEN 0x28
-#define MAC_TX_BUFF3_STATUS 0x30
-#define MAC_TX_BUFF3_ADDR 0x34
-#define MAC_TX_BUFF3_LEN 0x38
-
-#define MAC0_RX_DMA_ADDR 0xB4004100
-#define MAC1_RX_DMA_ADDR 0xB4004300
-/* offsets from MAC_RX_RING_ADDR */
-#define MAC_RX_BUFF0_STATUS 0x0
-# define RX_FRAME_LEN_MASK 0x3fff
-# define RX_WDOG_TIMER (1 << 14)
-# define RX_RUNT (1 << 15)
-# define RX_OVERLEN (1 << 16)
-# define RX_COLL (1 << 17)
-# define RX_ETHER (1 << 18)
-# define RX_MII_ERROR (1 << 19)
-# define RX_DRIBBLING (1 << 20)
-# define RX_CRC_ERROR (1 << 21)
-# define RX_VLAN1 (1 << 22)
-# define RX_VLAN2 (1 << 23)
-# define RX_LEN_ERROR (1 << 24)
-# define RX_CNTRL_FRAME (1 << 25)
-# define RX_U_CNTRL_FRAME (1 << 26)
-# define RX_MCAST_FRAME (1 << 27)
-# define RX_BCAST_FRAME (1 << 28)
-# define RX_FILTER_FAIL (1 << 29)
-# define RX_PACKET_FILTER (1 << 30)
-# define RX_MISSED_FRAME (1 << 31)
-
-# define RX_ERROR (RX_WDOG_TIMER | RX_RUNT | RX_OVERLEN | \
- RX_COLL | RX_MII_ERROR | RX_CRC_ERROR | \
- RX_LEN_ERROR | RX_U_CNTRL_FRAME | RX_MISSED_FRAME)
-#define MAC_RX_BUFF0_ADDR 0x4
-# define RX_DMA_ENABLE (1 << 0)
-# define RX_T_DONE (1 << 1)
-# define RX_GET_DMA_BUFFER(X) (((X) >> 2) & 0x3)
-# define RX_SET_BUFF_ADDR(X) ((X) & 0xffffffc0)
-#define MAC_RX_BUFF1_STATUS 0x10
-#define MAC_RX_BUFF1_ADDR 0x14
-#define MAC_RX_BUFF2_STATUS 0x20
-#define MAC_RX_BUFF2_ADDR 0x24
-#define MAC_RX_BUFF3_STATUS 0x30
-#define MAC_RX_BUFF3_ADDR 0x34
-
/*
* The IrDA peripheral has an IRFIRSEL pin, but on the DB/PB boards it's not
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index a78e4c1..ad8b058 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -89,6 +89,124 @@ MODULE_DESCRIPTION(DRV_DESC);
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
+/* AU1000 MAC registers and bits */
+#define MAC_CONTROL 0x0
+# define MAC_RX_ENABLE (1 << 2)
+# define MAC_TX_ENABLE (1 << 3)
+# define MAC_DEF_CHECK (1 << 5)
+# define MAC_SET_BL(X) (((X) & 0x3) << 6)
+# define MAC_AUTO_PAD (1 << 8)
+# define MAC_DISABLE_RETRY (1 << 10)
+# define MAC_DISABLE_BCAST (1 << 11)
+# define MAC_LATE_COL (1 << 12)
+# define MAC_HASH_MODE (1 << 13)
+# define MAC_HASH_ONLY (1 << 15)
+# define MAC_PASS_ALL (1 << 16)
+# define MAC_INVERSE_FILTER (1 << 17)
+# define MAC_PROMISCUOUS (1 << 18)
+# define MAC_PASS_ALL_MULTI (1 << 19)
+# define MAC_FULL_DUPLEX (1 << 20)
+# define MAC_NORMAL_MODE 0
+# define MAC_INT_LOOPBACK (1 << 21)
+# define MAC_EXT_LOOPBACK (1 << 22)
+# define MAC_DISABLE_RX_OWN (1 << 23)
+# define MAC_BIG_ENDIAN (1 << 30)
+# define MAC_RX_ALL (1 << 31)
+#define MAC_ADDRESS_HIGH 0x4
+#define MAC_ADDRESS_LOW 0x8
+#define MAC_MCAST_HIGH 0xC
+#define MAC_MCAST_LOW 0x10
+#define MAC_MII_CNTRL 0x14
+# define MAC_MII_BUSY (1 << 0)
+# define MAC_MII_READ 0
+# define MAC_MII_WRITE (1 << 1)
+# define MAC_SET_MII_SELECT_REG(X) (((X) & 0x1f) << 6)
+# define MAC_SET_MII_SELECT_PHY(X) (((X) & 0x1f) << 11)
+#define MAC_MII_DATA 0x18
+#define MAC_FLOW_CNTRL 0x1C
+# define MAC_FLOW_CNTRL_BUSY (1 << 0)
+# define MAC_FLOW_CNTRL_ENABLE (1 << 1)
+# define MAC_PASS_CONTROL (1 << 2)
+# define MAC_SET_PAUSE(X) (((X) & 0xffff) << 16)
+#define MAC_VLAN1_TAG 0x20
+#define MAC_VLAN2_TAG 0x24
+
+/* Ethernet Controller Enable */
+# define MAC_EN_CLOCK_ENABLE (1 << 0)
+# define MAC_EN_RESET0 (1 << 1)
+# define MAC_EN_TOSS (0 << 2)
+# define MAC_EN_CACHEABLE (1 << 3)
+# define MAC_EN_RESET1 (1 << 4)
+# define MAC_EN_RESET2 (1 << 5)
+# define MAC_DMA_RESET (1 << 6)
+
+/* Ethernet Controller DMA Channels */
+/* offsets from MAC_TX_RING_ADDR address */
+#define MAC_TX_BUFF0_STATUS 0x0
+# define TX_FRAME_ABORTED (1 << 0)
+# define TX_JAB_TIMEOUT (1 << 1)
+# define TX_NO_CARRIER (1 << 2)
+# define TX_LOSS_CARRIER (1 << 3)
+# define TX_EXC_DEF (1 << 4)
+# define TX_LATE_COLL_ABORT (1 << 5)
+# define TX_EXC_COLL (1 << 6)
+# define TX_UNDERRUN (1 << 7)
+# define TX_DEFERRED (1 << 8)
+# define TX_LATE_COLL (1 << 9)
+# define TX_COLL_CNT_MASK (0xF << 10)
+# define TX_PKT_RETRY (1 << 31)
+#define MAC_TX_BUFF0_ADDR 0x4
+# define TX_DMA_ENABLE (1 << 0)
+# define TX_T_DONE (1 << 1)
+# define TX_GET_DMA_BUFFER(X) (((X) >> 2) & 0x3)
+#define MAC_TX_BUFF0_LEN 0x8
+#define MAC_TX_BUFF1_STATUS 0x10
+#define MAC_TX_BUFF1_ADDR 0x14
+#define MAC_TX_BUFF1_LEN 0x18
+#define MAC_TX_BUFF2_STATUS 0x20
+#define MAC_TX_BUFF2_ADDR 0x24
+#define MAC_TX_BUFF2_LEN 0x28
+#define MAC_TX_BUFF3_STATUS 0x30
+#define MAC_TX_BUFF3_ADDR 0x34
+#define MAC_TX_BUFF3_LEN 0x38
+
+/* offsets from MAC_RX_RING_ADDR */
+#define MAC_RX_BUFF0_STATUS 0x0
+# define RX_FRAME_LEN_MASK 0x3fff
+# define RX_WDOG_TIMER (1 << 14)
+# define RX_RUNT (1 << 15)
+# define RX_OVERLEN (1 << 16)
+# define RX_COLL (1 << 17)
+# define RX_ETHER (1 << 18)
+# define RX_MII_ERROR (1 << 19)
+# define RX_DRIBBLING (1 << 20)
+# define RX_CRC_ERROR (1 << 21)
+# define RX_VLAN1 (1 << 22)
+# define RX_VLAN2 (1 << 23)
+# define RX_LEN_ERROR (1 << 24)
+# define RX_CNTRL_FRAME (1 << 25)
+# define RX_U_CNTRL_FRAME (1 << 26)
+# define RX_MCAST_FRAME (1 << 27)
+# define RX_BCAST_FRAME (1 << 28)
+# define RX_FILTER_FAIL (1 << 29)
+# define RX_PACKET_FILTER (1 << 30)
+# define RX_MISSED_FRAME (1 << 31)
+
+# define RX_ERROR (RX_WDOG_TIMER | RX_RUNT | RX_OVERLEN | \
+ RX_COLL | RX_MII_ERROR | RX_CRC_ERROR | \
+ RX_LEN_ERROR | RX_U_CNTRL_FRAME | RX_MISSED_FRAME)
+#define MAC_RX_BUFF0_ADDR 0x4
+# define RX_DMA_ENABLE (1 << 0)
+# define RX_T_DONE (1 << 1)
+# define RX_GET_DMA_BUFFER(X) (((X) >> 2) & 0x3)
+# define RX_SET_BUFF_ADDR(X) ((X) & 0xffffffc0)
+#define MAC_RX_BUFF1_STATUS 0x10
+#define MAC_RX_BUFF1_ADDR 0x14
+#define MAC_RX_BUFF2_STATUS 0x20
+#define MAC_RX_BUFF2_ADDR 0x24
+#define MAC_RX_BUFF3_STATUS 0x30
+#define MAC_RX_BUFF3_ADDR 0x34
+
/*
* Theory of operation
*
--
2.0.1
