When hotplug and/or a powered down idle state are supported cases will
arise where a non-zero VPE must be brought online without VPE 0, and it
where multiple VPEs must be onlined simultaneously. This patch prepares
for that by:
- Splitting struct boot_config into core & VPE boot config structures,
allocated one per core or VPE respectively. This allows for multiple
VPEs to be onlined simultaneously without clobbering each others
configuration.
- Indicating which VPEs should be online within a core at any given
time using a bitmap. This allows multiple VPEs to be brought online
simultaneously and also indicates to VPE 0 whether it should halt
after starting any non-zero VPEs that should be online within the
core. For example if all VPEs within a core are offlined via hotplug
and the user onlines the second VPE within that core:
1) The core will be powered up.
2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to
initialise the core.
3) VPE 0 will start VPE 1 because its bit is set in the cores
bitmap.
4) VPE 0 will halt itself because its bit is clear in the cores
bitmap.
- Moving the core & VPE initialisation to assembly code which does not
make any use of the stack. This is because if a non-zero VPE is to
be brought online in a powered down core then when VPE 0 of that
core runs it may not have a valid stack, and even if it did then
it's messy to run through parts of generic kernel code on VPE 0
before starting the correct VPE.
Signed-off-by: Paul Burton <paul.burton@xxxxxxxxxx>
---
arch/mips/include/asm/smp-cps.h | 14 +-
arch/mips/kernel/asm-offsets.c | 14 +-
arch/mips/kernel/cps-vec.S | 282 ++++++++++++++++++++++++++++++++++++++--
arch/mips/kernel/mips-cpc.c | 2 +
arch/mips/kernel/smp-cps.c | 223 ++++++++++++-------------------
5 files changed, 374 insertions(+), 161 deletions(-)
diff --git a/arch/mips/include/asm/smp-cps.h b/arch/mips/include/asm/smp-cps.h
index d60d1a2..d49279e 100644
--- a/arch/mips/include/asm/smp-cps.h
+++ b/arch/mips/include/asm/smp-cps.h
@@ -13,17 +13,23 @@
#ifndef __ASSEMBLY__
-struct boot_config {
- unsigned int core;
- unsigned int vpe;
+struct vpe_boot_config {
unsigned long pc;
unsigned long sp;
unsigned long gp;
};
-extern struct boot_config mips_cps_bootcfg;
+struct core_boot_config {
+ atomic_t vpe_mask;
+ struct vpe_boot_config *vpe_config;
+};
+
+extern struct core_boot_config *mips_cps_core_bootcfg;
extern void mips_cps_core_entry(void);
+extern void mips_cps_core_init(void);
+
+extern struct vpe_boot_config *mips_cps_boot_vpes(void);
#else /* __ASSEMBLY__ */
diff --git a/arch/mips/kernel/asm-offsets.c b/arch/mips/kernel/asm-offsets.c
index e085cde..d63490d 100644
--- a/arch/mips/kernel/asm-offsets.c
+++ b/arch/mips/kernel/asm-offsets.c
@@ -487,10 +487,14 @@ void output_kvm_defines(void)
void output_cps_defines(void)
{
COMMENT(" MIPS CPS offsets. ");
- OFFSET(BOOTCFG_CORE, boot_config, core);
- OFFSET(BOOTCFG_VPE, boot_config, vpe);
- OFFSET(BOOTCFG_PC, boot_config, pc);
- OFFSET(BOOTCFG_SP, boot_config, sp);
- OFFSET(BOOTCFG_GP, boot_config, gp);
+
+ OFFSET(COREBOOTCFG_VPEMASK, core_boot_config, vpe_mask);
+ OFFSET(COREBOOTCFG_VPECONFIG, core_boot_config, vpe_config);
+ DEFINE(COREBOOTCFG_SIZE, sizeof(struct core_boot_config));
+
+ OFFSET(VPEBOOTCFG_PC, vpe_boot_config, pc);
+ OFFSET(VPEBOOTCFG_SP, vpe_boot_config, sp);
+ OFFSET(VPEBOOTCFG_GP, vpe_boot_config, gp);
+ DEFINE(VPEBOOTCFG_SIZE, sizeof(struct vpe_boot_config));
}
#endif
diff --git a/arch/mips/kernel/cps-vec.S b/arch/mips/kernel/cps-vec.S
index f7a46db..57ec18c 100644
--- a/arch/mips/kernel/cps-vec.S
+++ b/arch/mips/kernel/cps-vec.S
@@ -14,12 +14,33 @@
#include <asm/asmmacro.h>
#include <asm/cacheops.h>
#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
-#define GCR_CL_COHERENCE_OFS 0x2008
+#define GCR_CL_COHERENCE_OFS 0x2008
+#define GCR_CL_ID_OFS 0x2028
+
+.extern mips_cm_base
+
+.set noreorder
+
+ /*
+ * Set dest to non-zero if the core supports the MT ASE, else zero. If
+ * MT is not supported then branch to nomt.
+ */
+ .macro has_mt dest, nomt
+ mfc0 \dest, CP0_CONFIG
+ bgez \dest, \nomt
+ mfc0 \dest, CP0_CONFIG, 1
+ bgez \dest, \nomt
+ mfc0 \dest, CP0_CONFIG, 2
+ bgez \dest, \nomt
+ mfc0 \dest, CP0_CONFIG, 3
+ andi \dest, \dest, MIPS_CONF3_MT
+ beqz \dest, \nomt
+ .endm
.section .text.cps-vec
.balign 0x1000
-.set noreorder
LEAF(mips_cps_core_entry)
/*
@@ -134,21 +155,24 @@ dcache_done:
jr t0
nop
-1: /* We're up, cached & coherent */
+ /*
+ * We're up, cached & coherent. Perform any further required core-level
+ * initialisation.
+ */
+1: jal mips_cps_core_init
+ nop
/*
- * TODO: We should check the VPE number we intended to boot here, and
- * if non-zero we should start that VPE and stop this one. For
- * the moment this doesn't matter since CPUs are brought up
- * sequentially and in order, but once hotplug is implemented
- * this will need revisiting.
+ * Boot any other VPEs within this core that should be online, and
+ * deactivate this VPE if it should be offline.
*/
+ jal mips_cps_boot_vpes
+ nop
/* Off we go! */
- la t0, mips_cps_bootcfg
- lw t1, BOOTCFG_PC(t0)
- lw gp, BOOTCFG_GP(t0)
- lw sp, BOOTCFG_SP(t0)
+ lw t1, VPEBOOTCFG_PC(v0)
+ lw gp, VPEBOOTCFG_GP(v0)
+ lw sp, VPEBOOTCFG_SP(v0)
jr t1
nop
END(mips_cps_core_entry)
@@ -189,3 +213,237 @@ LEAF(excep_ejtag)
jr k0
nop
END(excep_ejtag)
+
+LEAF(mips_cps_core_init)
+#ifdef CONFIG_MIPS_MT
+ /* Check that the core implements the MT ASE */
+ has_mt t0, 3f
+ nop
+
+ .set push
+ .set mt
+
+ /* Only allow 1 TC per VPE to execute... */
+ dmt
+
+ /* ...and for the moment only 1 VPE */
+ dvpe
+ la t1, 1f
+ jr.hb t1
+ nop
+
+ /* Enter VPE configuration state */
+1: mfc0 t0, CP0_MVPCONTROL
+ ori t0, t0, MVPCONTROL_VPC
+ mtc0 t0, CP0_MVPCONTROL
+
+ /* Retrieve the number of VPEs within the core */
+ mfc0 t0, CP0_MVPCONF0
+ srl t0, t0, MVPCONF0_PVPE_SHIFT
+ andi t0, t0, (MVPCONF0_PVPE >> MVPCONF0_PVPE_SHIFT)
+ addi t7, t0, 1
+
+ /* If there's only 1, we're done */
+ beqz t0, 2f
+ nop
+
+ /* Loop through each VPE within this core */
+ li t5, 1
+
+1: /* Operate on the appropriate TC */
+ mtc0 t5, CP0_VPECONTROL
+ ehb
+
+ /* Bind TC to VPE (1:1 TC:VPE mapping) */
+ mttc0 t5, CP0_TCBIND
+
+ /* Set exclusive TC, non-active, master */
+ li t0, VPECONF0_MVP
+ sll t1, t5, VPECONF0_XTC_SHIFT
+ or t0, t0, t1
+ mttc0 t0, CP0_VPECONF0
+
+ /* Set TC non-active, non-allocatable */
+ mttc0 zero, CP0_TCSTATUS
+
+ /* Set TC halted */
+ li t0, TCHALT_H
+ mttc0 t0, CP0_TCHALT
+
+ /* Next VPE */
+ addi t5, t5, 1
+ slt t0, t5, t7
+ bnez t0, 1b
+ nop
+
+ /* Leave VPE configuration state */
+2: mfc0 t0, CP0_MVPCONTROL
+ xori t0, t0, MVPCONTROL_VPC
+ mtc0 t0, CP0_MVPCONTROL
+
+3: .set pop
+#endif
+ jr ra
+ nop
+ END(mips_cps_core_init)
+
+LEAF(mips_cps_boot_vpes)
+ /* Retrieve CM base address */
+ la t0, mips_cm_base
+ lw t0, 0(t0)
+
+ /* Calculate a pointer to this cores struct core_boot_config */
+ lw t0, GCR_CL_ID_OFS(t0)
+ li t1, COREBOOTCFG_SIZE
+ mul t0, t0, t1
+ la t1, mips_cps_core_bootcfg
+ lw t1, 0(t1)
+ addu t0, t0, t1
+
+ /* Calculate this VPEs ID. If the core doesn't support MT use 0 */
+ has_mt t6, 1f
+ li t9, 0
+
+ /* Find the number of VPEs present in the core */
+ mfc0 t1, CP0_MVPCONF0
+ srl t1, t1, MVPCONF0_PVPE_SHIFT
+ andi t1, t1, MVPCONF0_PVPE >> MVPCONF0_PVPE_SHIFT
+ addi t1, t1, 1
+
+ /* Calculate a mask for the VPE ID from EBase.CPUNum */
+ clz t1, t1
+ li t2, 31
+ subu t1, t2, t1
+ li t2, 1
+ sll t1, t2, t1
+ addiu t1, t1, -1
+
+ /* Retrieve the VPE ID from EBase.CPUNum */
+ mfc0 t9, $15, 1
+ and t9, t9, t1
+
+1: /* Calculate a pointer to this VPEs struct vpe_boot_config */
+ li t1, VPEBOOTCFG_SIZE
+ mul v0, t9, t1
+ lw t7, COREBOOTCFG_VPECONFIG(t0)
+ addu v0, v0, t7
+
+#ifdef CONFIG_MIPS_MT
+
+ /* If the core doesn't support MT then return */
+ bnez t6, 1f
+ nop
+ jr ra
+ nop
+
+ .set push
+ .set mt
+
+1: /* Enter VPE configuration state */
+ dvpe
+ la t1, 1f
+ jr.hb t1
+ nop
+1: mfc0 t1, CP0_MVPCONTROL
+ ori t1, t1, MVPCONTROL_VPC
+ mtc0 t1, CP0_MVPCONTROL
+ ehb
+
+ /* Loop through each VPE */
+ lw t6, COREBOOTCFG_VPEMASK(t0)
+ move t8, t6
+ li t5, 0
+
+ /* Check whether the VPE should be running. If not, skip it */
+1: andi t0, t6, 1
+ beqz t0, 2f
+ nop
+
+ /* Operate on the appropriate TC */
+ mfc0 t0, CP0_VPECONTROL
+ ori t0, t0, VPECONTROL_TARGTC
+ xori t0, t0, VPECONTROL_TARGTC
+ or t0, t0, t5
+ mtc0 t0, CP0_VPECONTROL
+ ehb
+
+ /* Skip the VPE if its TC is not halted */
+ mftc0 t0, CP0_TCHALT
+ beqz t0, 2f
+ nop
+
+ /* Calculate a pointer to the VPEs struct vpe_boot_config */
+ li t0, VPEBOOTCFG_SIZE
+ mul t0, t0, t5
+ addu t0, t0, t7
+
+ /* Set the TC restart PC */
+ lw t1, VPEBOOTCFG_PC(t0)
+ mttc0 t1, CP0_TCRESTART
+
+ /* Set the TC stack pointer */
+ lw t1, VPEBOOTCFG_SP(t0)
+ mttgpr t1, sp
+
+ /* Set the TC global pointer */
+ lw t1, VPEBOOTCFG_GP(t0)
+ mttgpr t1, gp
+
+ /* Copy config from this VPE */
+ mfc0 t0, CP0_CONFIG
+ mttc0 t0, CP0_CONFIG
+
+ /* Ensure no software interrupts are pending */
+ mttc0 zero, CP0_CAUSE
+ mttc0 zero, CP0_STATUS
+
+ /* Set TC active, not interrupt exempt */
+ mftc0 t0, CP0_TCSTATUS
+ li t1, ~TCSTATUS_IXMT
+ and t0, t0, t1
+ ori t0, t0, TCSTATUS_A
+ mttc0 t0, CP0_TCSTATUS
+
+ /* Clear the TC halt bit */
+ mttc0 zero, CP0_TCHALT
+
+ /* Set VPE active */
+ mftc0 t0, CP0_VPECONF0
+ ori t0, t0, VPECONF0_VPA
+ mttc0 t0, CP0_VPECONF0
+
+ /* Next VPE */
+2: srl t6, t6, 1
+ addi t5, t5, 1
+ bnez t6, 1b
+ nop
+
+ /* Leave VPE configuration state */
+ mfc0 t1, CP0_MVPCONTROL
+ xori t1, t1, MVPCONTROL_VPC
+ mtc0 t1, CP0_MVPCONTROL
+ ehb
+ evpe
+
+ /* Check whether this VPE is meant to be running */
+ li t0, 1
+ sll t0, t0, t9
+ and t0, t0, t8
+ bnez t0, 2f
+ nop
+
+ /* This VPE should be offline, halt the TC */
+ li t0, TCHALT_H
+ mtc0 t0, CP0_TCHALT
+ la t0, 1f
+1: jr.hb t0
+ nop
+
+2: .set pop
+
+#endif /* CONFIG_MIPS_MT */
+
+ /* Return */
+ jr ra
+ nop
+ END(mips_cps_boot_vpes)
diff --git a/arch/mips/kernel/mips-cpc.c b/arch/mips/kernel/mips-cpc.c
index 2368fc5..ba47360 100644
--- a/arch/mips/kernel/mips-cpc.c
+++ b/arch/mips/kernel/mips-cpc.c
@@ -9,6 +9,8 @@
*/
#include <linux/errno.h>
+#include <linux/percpu.h>
+#include <linux/spinlock.h>
#include <asm/mips-cm.h>
#include <asm/mips-cpc.h>
diff --git a/arch/mips/kernel/smp-cps.c b/arch/mips/kernel/smp-cps.c
index 536eec0..af90e82 100644
--- a/arch/mips/kernel/smp-cps.c
+++ b/arch/mips/kernel/smp-cps.c
@@ -26,98 +26,37 @@
static DECLARE_BITMAP(core_power, NR_CPUS);
-struct boot_config mips_cps_bootcfg;
+struct core_boot_config *mips_cps_core_bootcfg;
-static void init_core(void)
+static unsigned core_vpe_count(unsigned core)
{
- unsigned int nvpes, t;
- u32 mvpconf0, vpeconf0, vpecontrol, tcstatus, tcbind, status;
+ unsigned cfg;
- if (!cpu_has_mipsmt)
- return;
-
- /* Enter VPE configuration state */
- dvpe();
- set_c0_mvpcontrol(MVPCONTROL_VPC);
-
- /* Retrieve the count of VPEs in this core */
- mvpconf0 = read_c0_mvpconf0();
- nvpes = ((mvpconf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT) + 1;
- smp_num_siblings = nvpes;
-
- for (t = 1; t < nvpes; t++) {
- /* Use a 1:1 mapping of TC index to VPE index */
- settc(t);
-
- /* Bind 1 TC to this VPE */
- tcbind = read_tc_c0_tcbind();
- tcbind &= ~TCBIND_CURVPE;
- tcbind |= t << TCBIND_CURVPE_SHIFT;
- write_tc_c0_tcbind(tcbind);
-
- /* Set exclusive TC, non-active, master */
- vpeconf0 = read_vpe_c0_vpeconf0();
- vpeconf0 &= ~(VPECONF0_XTC | VPECONF0_VPA);
- vpeconf0 |= t << VPECONF0_XTC_SHIFT;
- vpeconf0 |= VPECONF0_MVP;
- write_vpe_c0_vpeconf0(vpeconf0);
-
- /* Declare TC non-active, non-allocatable & interrupt exempt */
- tcstatus = read_tc_c0_tcstatus();
- tcstatus &= ~(TCSTATUS_A | TCSTATUS_DA);
- tcstatus |= TCSTATUS_IXMT;
- write_tc_c0_tcstatus(tcstatus);
-
- /* Halt the TC */
- write_tc_c0_tchalt(TCHALT_H);
-
- /* Allow only 1 TC to execute */
- vpecontrol = read_vpe_c0_vpecontrol();
- vpecontrol &= ~VPECONTROL_TE;
- write_vpe_c0_vpecontrol(vpecontrol);
-
- /* Copy (most of) Status from VPE 0 */
- status = read_c0_status();
- status &= ~(ST0_IM | ST0_IE | ST0_KSU);
- status |= ST0_CU0;
- write_vpe_c0_status(status);
-
- /* Copy Config from VPE 0 */
- write_vpe_c0_config(read_c0_config());
- write_vpe_c0_config7(read_c0_config7());
-
- /* Ensure no software interrupts are pending */
- write_vpe_c0_cause(0);
-
- /* Sync Count */
- write_vpe_c0_count(read_c0_count());
- }
+ if (!config_enabled(CONFIG_MIPS_MT_SMP) || !cpu_has_mipsmt)
+ return 1;
- /* Leave VPE configuration state */
- clear_c0_mvpcontrol(MVPCONTROL_VPC);
+ write_gcr_cl_other(core << CM_GCR_Cx_OTHER_CORENUM_SHF);
+ cfg = read_gcr_co_config() & CM_GCR_Cx_CONFIG_PVPE_MSK;
+ return (cfg >> CM_GCR_Cx_CONFIG_PVPE_SHF) + 1;
}
static void __init cps_smp_setup(void)
{
unsigned int ncores, nvpes, core_vpes;
int c, v;
- u32 core_cfg, *entry_code;
+ u32 *entry_code;
/* Detect & record VPE topology */
ncores = mips_cm_numcores();
pr_info("VPE topology ");
for (c = nvpes = 0; c < ncores; c++) {
- if (cpu_has_mipsmt && config_enabled(CONFIG_MIPS_MT_SMP)) {
- write_gcr_cl_other(c << CM_GCR_Cx_OTHER_CORENUM_SHF);
- core_cfg = read_gcr_co_config();
- core_vpes = ((core_cfg & CM_GCR_Cx_CONFIG_PVPE_MSK) >>
- CM_GCR_Cx_CONFIG_PVPE_SHF) + 1;
- } else {
- core_vpes = 1;
- }
-
+ core_vpes = core_vpe_count(c);
pr_cont("%c%u", c ? ',' : '{', core_vpes);
+ /* Use the number of VPEs in core 0 for smp_num_siblings */
+ if (!c)
+ smp_num_siblings = core_vpes;
+
for (v = 0; v < min_t(int, core_vpes, NR_CPUS - nvpes); v++) {
cpu_data[nvpes + v].core = c;
#ifdef CONFIG_MIPS_MT_SMP
@@ -140,12 +79,8 @@ static void __init cps_smp_setup(void)
/* Core 0 is powered up (we're running on it) */
bitmap_set(core_power, 0, 1);
- /* Disable MT - we only want to run 1 TC per VPE */
- if (cpu_has_mipsmt)
- dmt();
-
/* Initialise core 0 */
- init_core();
+ mips_cps_core_init();
/* Patch the start of mips_cps_core_entry to provide the CM base */
entry_code = (u32 *)&mips_cps_core_entry;
@@ -157,15 +92,60 @@ static void __init cps_smp_setup(void)
static void __init cps_prepare_cpus(unsigned int max_cpus)
{
+ unsigned ncores, core_vpes, c;
+
mips_mt_set_cpuoptions();
+
+ /* Allocate core boot configuration structs */
+ ncores = mips_cm_numcores();
+ mips_cps_core_bootcfg = kcalloc(ncores, sizeof(*mips_cps_core_bootcfg),
+ GFP_KERNEL);
+ if (!mips_cps_core_bootcfg) {
+ pr_err("Failed to allocate boot config for %u cores\n", ncores);
+ goto err_out;
+ }
+
+ /* Allocate VPE boot configuration structs */
+ for (c = 0; c < ncores; c++) {
+ core_vpes = core_vpe_count(c);
+ mips_cps_core_bootcfg[c].vpe_config = kcalloc(core_vpes,
+ sizeof(*mips_cps_core_bootcfg[c].vpe_config),
+ GFP_KERNEL);
+ if (!mips_cps_core_bootcfg[c].vpe_config) {
+ pr_err("Failed to allocate %u VPE boot configs\n",
+ core_vpes);
+ goto err_out;
+ }
+ }
+
+ /* Mark this CPU as booted */
+ atomic_set(&mips_cps_core_bootcfg[current_cpu_data.core].vpe_mask,
+ 1 << cpu_vpe_id(¤t_cpu_data));
+
+ return;
+err_out:
+ /* Clean up allocations */
+ if (mips_cps_core_bootcfg) {
+ for (c = 0; c < ncores; c++)
+ kfree(mips_cps_core_bootcfg[c].vpe_config);
+ kfree(mips_cps_core_bootcfg);
+ mips_cps_core_bootcfg = NULL;
+ }
+
+ /* Effectively disable SMP by declaring CPUs not present */
+ for_each_possible_cpu(c) {
+ if (c == 0)
+ continue;
+ set_cpu_present(c, false);
+ }
}
-static void boot_core(struct boot_config *cfg)
+static void boot_core(unsigned core)
{
u32 access;
/* Select the appropriate core */
- write_gcr_cl_other(cfg->core << CM_GCR_Cx_OTHER_CORENUM_SHF);
+ write_gcr_cl_other(core << CM_GCR_Cx_OTHER_CORENUM_SHF);
/* Set its reset vector */
write_gcr_co_reset_base(CKSEG1ADDR((unsigned long)mips_cps_core_entry));
@@ -175,15 +155,12 @@ static void boot_core(struct boot_config *cfg)
/* Ensure the core can access the GCRs */
access = read_gcr_access();
- access |= 1 << (CM_GCR_ACCESS_ACCESSEN_SHF + cfg->core);
+ access |= 1 << (CM_GCR_ACCESS_ACCESSEN_SHF + core);
write_gcr_access(access);
- /* Copy cfg */
- mips_cps_bootcfg = *cfg;
-
if (mips_cpc_present()) {
/* Select the appropriate core */
- write_cpc_cl_other(cfg->core << CPC_Cx_OTHER_CORENUM_SHF);
+ write_cpc_cl_other(core << CPC_Cx_OTHER_CORENUM_SHF);
/* Reset the core */
write_cpc_co_cmd(CPC_Cx_CMD_RESET);
@@ -193,77 +170,47 @@ static void boot_core(struct boot_config *cfg)
}
/* The core is now powered up */
- bitmap_set(core_power, cfg->core, 1);
+ bitmap_set(core_power, core, 1);
}
-static void boot_vpe(void *info)
+static void remote_vpe_boot(void *dummy)
{
- struct boot_config *cfg = info;
- u32 tcstatus, vpeconf0;
-
- /* Enter VPE configuration state */
- dvpe();
- set_c0_mvpcontrol(MVPCONTROL_VPC);
-
- settc(cfg->vpe);
-
- /* Set the TC restart PC */
- write_tc_c0_tcrestart((unsigned long)&smp_bootstrap);
-
- /* Activate the TC, allow interrupts */
- tcstatus = read_tc_c0_tcstatus();
- tcstatus &= ~TCSTATUS_IXMT;
- tcstatus |= TCSTATUS_A;
- write_tc_c0_tcstatus(tcstatus);
-
- /* Clear the TC halt bit */
- write_tc_c0_tchalt(0);
-
- /* Activate the VPE */
- vpeconf0 = read_vpe_c0_vpeconf0();
- vpeconf0 |= VPECONF0_VPA;
- write_vpe_c0_vpeconf0(vpeconf0);
-
- /* Set the stack & global pointer registers */
- write_tc_gpr_sp(cfg->sp);
- write_tc_gpr_gp(cfg->gp);
-
- /* Leave VPE configuration state */
- clear_c0_mvpcontrol(MVPCONTROL_VPC);
-
- /* Enable other VPEs to execute */
- evpe(EVPE_ENABLE);
+ mips_cps_boot_vpes();
}
static void cps_boot_secondary(int cpu, struct task_struct *idle)
{
- struct boot_config cfg;
+ unsigned core = cpu_data[cpu].core;
+ unsigned vpe_id = cpu_vpe_id(&cpu_data[cpu]);
+ struct core_boot_config *core_cfg = &mips_cps_core_bootcfg[core];
+ struct vpe_boot_config *vpe_cfg = &core_cfg->vpe_config[vpe_id];
unsigned int remote;
int err;
- cfg.core = cpu_data[cpu].core;
- cfg.vpe = cpu_vpe_id(&cpu_data[cpu]);
- cfg.pc = (unsigned long)&smp_bootstrap;
- cfg.sp = __KSTK_TOS(idle);
- cfg.gp = (unsigned long)task_thread_info(idle);
+ vpe_cfg->pc = (unsigned long)&smp_bootstrap;
+ vpe_cfg->sp = __KSTK_TOS(idle);
+ vpe_cfg->gp = (unsigned long)task_thread_info(idle);
- if (!test_bit(cfg.core, core_power)) {
+ atomic_or(1 << cpu_vpe_id(&cpu_data[cpu]), &core_cfg->vpe_mask);
+
+ if (!test_bit(core, core_power)) {
/* Boot a VPE on a powered down core */
- boot_core(&cfg);
+ boot_core(core);
return;
}
- if (cfg.core != current_cpu_data.core) {
+ if (core != current_cpu_data.core) {
/* Boot a VPE on another powered up core */
for (remote = 0; remote < NR_CPUS; remote++) {
- if (cpu_data[remote].core != cfg.core)
+ if (cpu_data[remote].core != core)
continue;
if (cpu_online(remote))
break;
}
BUG_ON(remote >= NR_CPUS);
- err = smp_call_function_single(remote, boot_vpe, &cfg, 1);
+ err = smp_call_function_single(remote, remote_vpe_boot,
+ NULL, 1);
if (err)
panic("Failed to call remote CPU\n");
return;
@@ -272,7 +219,7 @@ static void cps_boot_secondary(int cpu, struct task_struct *idle)
BUG_ON(!cpu_has_mipsmt);
/* Boot a VPE on this core */
- boot_vpe(&cfg);
+ mips_cps_boot_vpes();
}
static void cps_init_secondary(void)
@@ -281,10 +228,6 @@ static void cps_init_secondary(void)
if (cpu_has_mipsmt)
dmt();
- /* TODO: revisit this assumption once hotplug is implemented */
- if (cpu_vpe_id(¤t_cpu_data) == 0)
- init_core();
-
change_c0_status(ST0_IM, STATUSF_IP3 | STATUSF_IP4 |
STATUSF_IP6 | STATUSF_IP7);
}
--
1.8.5.3
