Tips of Loongson's CPU hotplug:
1, To fully shutdown a core in Loongson 3, the target core should go to
CKSEG1 and flush all L1 cache entries at first. Then, another core
(usually Core 0) can safely disable the clock of the target core. So
play_dead() call loongson3_play_dead() via CKSEG1 (both uncached and
unmmaped).
2, The default clocksource of Loongson is MIPS. Since clock source is a
global device, timekeeping need the CP0' Count registers of each core
be synchronous. Thus, when a core is up, we use a SMP_ASK_C0COUNT IPI
to ask Core-0's Count.
Signed-off-by: Huacai Chen <chenhc@xxxxxxxxxx>
Signed-off-by: Hongliang Tao <taohl@xxxxxxxxxx>
Signed-off-by: Hua Yan <yanh@xxxxxxxxxx>
---
arch/mips/include/asm/mach-loongson/irq.h | 1 +
arch/mips/include/asm/mach-loongson/loongson.h | 6 +-
arch/mips/include/asm/smp.h | 1 +
arch/mips/loongson/Kconfig | 1 +
arch/mips/loongson/loongson-3/irq.c | 10 ++
arch/mips/loongson/loongson-3/smp.c | 171 +++++++++++++++++++++++-
6 files changed, 185 insertions(+), 5 deletions(-)
diff --git a/arch/mips/include/asm/mach-loongson/irq.h b/arch/mips/include/asm/mach-loongson/irq.h
index d2f0e2a..620b3e9 100644
--- a/arch/mips/include/asm/mach-loongson/irq.h
+++ b/arch/mips/include/asm/mach-loongson/irq.h
@@ -22,6 +22,7 @@
#endif
+extern void fixup_irqs(void);
extern void loongson3_ipi_interrupt(struct pt_regs *regs);
#include_next <irq.h>
diff --git a/arch/mips/include/asm/mach-loongson/loongson.h b/arch/mips/include/asm/mach-loongson/loongson.h
index f185907..f3fd1eb 100644
--- a/arch/mips/include/asm/mach-loongson/loongson.h
+++ b/arch/mips/include/asm/mach-loongson/loongson.h
@@ -249,6 +249,9 @@ static inline void do_perfcnt_IRQ(void)
#define LOONGSON_PXARB_CFG LOONGSON_REG(LOONGSON_REGBASE + 0x68)
#define LOONGSON_PXARB_STATUS LOONGSON_REG(LOONGSON_REGBASE + 0x6c)
+/* Chip Config */
+#define LOONGSON_CHIPCFG0 LOONGSON_REG(LOONGSON_REGBASE + 0x80)
+
/* pcimap */
#define LOONGSON_PCIMAP_PCIMAP_LO0 0x0000003f
@@ -264,9 +267,6 @@ static inline void do_perfcnt_IRQ(void)
#ifdef CONFIG_CPU_SUPPORTS_CPUFREQ
#include <linux/cpufreq.h>
extern struct cpufreq_frequency_table loongson2_clockmod_table[];
-
-/* Chip Config */
-#define LOONGSON_CHIPCFG0 LOONGSON_REG(LOONGSON_REGBASE + 0x80)
#endif
/*
diff --git a/arch/mips/include/asm/smp.h b/arch/mips/include/asm/smp.h
index eb60087..efa02ac 100644
--- a/arch/mips/include/asm/smp.h
+++ b/arch/mips/include/asm/smp.h
@@ -42,6 +42,7 @@ extern int __cpu_logical_map[NR_CPUS];
#define SMP_ICACHE_FLUSH 0x4
/* Used by kexec crashdump to save all cpu's state */
#define SMP_DUMP 0x8
+#define SMP_ASK_C0COUNT 0x10
extern volatile cpumask_t cpu_callin_map;
diff --git a/arch/mips/loongson/Kconfig b/arch/mips/loongson/Kconfig
index 4f3967c..f29e604 100644
--- a/arch/mips/loongson/Kconfig
+++ b/arch/mips/loongson/Kconfig
@@ -77,6 +77,7 @@ config LEMOTE_MACH3A
select SYS_HAS_CPU_LOONGSON3
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_SMP
+ select SYS_SUPPORTS_HOTPLUG_CPU
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
diff --git a/arch/mips/loongson/loongson-3/irq.c b/arch/mips/loongson/loongson-3/irq.c
index d8920a8..d457366 100644
--- a/arch/mips/loongson/loongson-3/irq.c
+++ b/arch/mips/loongson/loongson-3/irq.c
@@ -128,3 +128,13 @@ void __init mach_init_irq(void)
set_c0_status(STATUSF_IP2 | STATUSF_IP6);
}
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+void fixup_irqs(void)
+{
+ irq_cpu_offline();
+ clear_c0_status(ST0_IM);
+}
+
+#endif
diff --git a/arch/mips/loongson/loongson-3/smp.c b/arch/mips/loongson/loongson-3/smp.c
index a264bcb..059ef94 100644
--- a/arch/mips/loongson/loongson-3/smp.c
+++ b/arch/mips/loongson/loongson-3/smp.c
@@ -26,10 +26,14 @@
#include <asm/time.h>
#include <asm/clock.h>
#include <asm/tlbflush.h>
+#include <asm/cacheflush.h>
#include <loongson.h>
#include "smp.h"
+DEFINE_PER_CPU(int, cpu_state);
+DEFINE_PER_CPU(uint32_t, core0_c0count);
+
/* read a 64bit value from ipi register */
uint64_t loongson3_ipi_read64(void *addr)
{
@@ -170,8 +174,8 @@ loongson3_send_ipi_mask(const struct cpumask *mask, unsigned int action)
void loongson3_ipi_interrupt(struct pt_regs *regs)
{
- int cpu = smp_processor_id();
- unsigned int action;
+ int i, cpu = smp_processor_id();
+ unsigned int action, c0count;
/* Load the ipi register to figure out what we're supposed to do */
action = loongson3_ipi_read32(ipi_status0_regs[cpu]);
@@ -184,14 +188,24 @@ void loongson3_ipi_interrupt(struct pt_regs *regs)
if (action & SMP_CALL_FUNCTION)
smp_call_function_interrupt();
+
+ if (action & SMP_ASK_C0COUNT) {
+ BUG_ON(cpu != 0);
+ c0count = read_c0_count();
+ for (i = 1; i < loongson_sysconf.nr_cpus; i++)
+ per_cpu(core0_c0count, i) = c0count;
+ }
}
+#define MAX_LOOPS 1000
/*
* SMP init and finish on secondary CPUs
*/
void loongson3_init_secondary(void)
{
int i;
+ uint32_t initcount;
+ unsigned int cpu = smp_processor_id();
unsigned int imask = STATUSF_IP7 | STATUSF_IP6 |
STATUSF_IP3 | STATUSF_IP2;
@@ -200,6 +214,21 @@ void loongson3_init_secondary(void)
for (i = 0; i < loongson_sysconf.nr_cpus; i++)
loongson3_ipi_write32(0xffffffff, ipi_en0_regs[i]);
+
+ per_cpu(cpu_state, cpu) = CPU_ONLINE;
+
+ i = 0;
+ __get_cpu_var(core0_c0count) = 0;
+ loongson3_send_ipi_single(0, SMP_ASK_C0COUNT);
+ while (!__get_cpu_var(core0_c0count)) {
+ i++;
+ cpu_relax();
+ }
+
+ if (i > MAX_LOOPS)
+ i = MAX_LOOPS;
+ initcount = __get_cpu_var(core0_c0count) + i;
+ write_c0_count(initcount);
}
void loongson3_smp_finish(void)
@@ -234,6 +263,8 @@ void __init loongson3_smp_setup(void)
void __init loongson3_prepare_cpus(unsigned int max_cpus)
{
+ init_cpu_present(cpu_possible_mask);
+ per_cpu(cpu_state, smp_processor_id()) = CPU_ONLINE;
}
/*
@@ -267,6 +298,138 @@ void __init loongson3_cpus_done(void)
{
}
+#ifdef CONFIG_HOTPLUG_CPU
+
+static int loongson3_cpu_disable(void)
+{
+ unsigned long flags;
+ unsigned int cpu = smp_processor_id();
+
+ if (cpu == 0)
+ return -EBUSY;
+
+ set_cpu_online(cpu, false);
+ cpu_clear(cpu, cpu_callin_map);
+ local_irq_save(flags);
+ fixup_irqs();
+ local_irq_restore(flags);
+ flush_cache_all();
+ local_flush_tlb_all();
+
+ return 0;
+}
+
+
+static void loongson3_cpu_die(unsigned int cpu)
+{
+ while (per_cpu(cpu_state, cpu) != CPU_DEAD)
+ cpu_relax();
+
+ mb();
+}
+
+/* To shutdown a core in Loongson 3, the target core should go to CKSEG1 and
+ * flush all L1 entries at first. Then, another core (usually Core 0) can
+ * safely disable the clock of the target core. loongson3_play_dead() is
+ * called via CKSEG1 (uncached and unmmaped) */
+void loongson3_play_dead(int *state_addr)
+{
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set noreorder \n"
+ " li $t0, 0x80000000 \n" /* KSEG0 */
+ " move $t1, %0 \n" /* num of L1 entries */
+ "1: cache 0, 0($t0) \n" /* flush L1 ICache */
+ " cache 0, 1($t0) \n"
+ " cache 0, 2($t0) \n"
+ " cache 0, 3($t0) \n"
+ " cache 1, 0($t0) \n" /* flush L1 DCache */
+ " cache 1, 1($t0) \n"
+ " cache 1, 2($t0) \n"
+ " cache 1, 3($t0) \n"
+ " addiu $t0, $t0, 0x20 \n"
+ " bnez $t1, 1b \n"
+ " addiu $t1, $t1, -1 \n"
+ " li $t0, 0x7 \n" /* *state_addr = CPU_DEAD; */
+ " sw $t0, 0($a0) \n"
+ " sync \n"
+ " cache 21, 0($a0) \n" /* flush entry of *state_addr */
+ " .set pop \n"
+ : /* No Output */
+ : "r" (cpu_data[0].dcache.sets));
+
+ __asm__ __volatile__(
+ " .set push \n"
+ " .set noreorder \n"
+ " .set mips64 \n"
+ " mfc0 $t2, $15, 1 \n"
+ " andi $t2, 0x3ff \n"
+ " dli $t0, 0x900000003ff01000 \n"
+ " andi $t3, $t2, 0x3 \n"
+ " sll $t3, 8 \n" /* get cpu id */
+ " or $t0, $t0, $t3 \n"
+ " andi $t1, $t2, 0xc \n"
+ " dsll $t1, 42 \n" /* get node id */
+ " or $t0, $t0, $t1 \n"
+ "1: li $a0, 0x100 \n" /* wait for init loop */
+ "2: bnez $a0, 2b \n" /* idle loop */
+ " addiu $a0, -1 \n"
+ " lw $v0, 0x20($t0) \n" /* get PC via mailbox */
+ " beqz $v0, 1b \n"
+ " nop \n"
+ " ld $sp, 0x28($t0) \n" /* get SP via mailbox */
+ " ld $gp, 0x30($t0) \n" /* get GP via mailbox */
+ " ld $a1, 0x38($t0) \n"
+ " jr $v0 \n" /* jump to initial PC */
+ " nop \n"
+ " .set pop \n");
+}
+
+void play_dead(void)
+{
+ int *state_addr;
+ unsigned int cpu = smp_processor_id();
+ void (*play_dead_at_ckseg1)(int *);
+
+ idle_task_exit();
+ play_dead_at_ckseg1 =
+ (void *)CKSEG1ADDR((unsigned long)loongson3_play_dead);
+ state_addr = &per_cpu(cpu_state, cpu);
+ mb();
+ play_dead_at_ckseg1(state_addr);
+}
+
+#define CPU_POST_DEAD_FROZEN (CPU_POST_DEAD | CPU_TASKS_FROZEN)
+static int loongson3_cpu_callback(struct notifier_block *nfb,
+ unsigned long action, void *hcpu)
+{
+ unsigned int cpu = (unsigned long)hcpu;
+
+ switch (action) {
+ case CPU_POST_DEAD:
+ case CPU_POST_DEAD_FROZEN:
+ pr_info("Disable clock for CPU#%d\n", cpu);
+ LOONGSON_CHIPCFG0 &= ~(1 << (12 + cpu));
+ break;
+ case CPU_UP_PREPARE:
+ case CPU_UP_PREPARE_FROZEN:
+ pr_info("Enable clock for CPU#%d\n", cpu);
+ LOONGSON_CHIPCFG0 |= 1 << (12 + cpu);
+ break;
+ }
+
+ return NOTIFY_OK;
+}
+
+static int register_loongson3_notifier(void)
+{
+ hotcpu_notifier(loongson3_cpu_callback, 0);
+ return 0;
+}
+early_initcall(register_loongson3_notifier);
+
+#endif
+
struct plat_smp_ops loongson3_smp_ops = {
.send_ipi_single = loongson3_send_ipi_single,
.send_ipi_mask = loongson3_send_ipi_mask,
@@ -276,4 +439,8 @@ struct plat_smp_ops loongson3_smp_ops = {
.boot_secondary = loongson3_boot_secondary,
.smp_setup = loongson3_smp_setup,
.prepare_cpus = loongson3_prepare_cpus,
+#ifdef CONFIG_HOTPLUG_CPU
+ .cpu_disable = loongson3_cpu_disable,
+ .cpu_die = loongson3_cpu_die,
+#endif
};
--
1.7.7.3
