No change in logic, the changes are: * cleanup some whitespace and comments * remove confusing argument of SYS_CPU_COHERENT_BASE macro * make the numerical labels in macros consistent Signed-off-by: Jayachandran C <jchandra@xxxxxxxxxxxx> --- arch/mips/netlogic/common/reset.S | 29 +++++++++++++++-------------- arch/mips/netlogic/common/smpboot.S | 3 ++- 2 files changed, 17 insertions(+), 15 deletions(-) diff --git a/arch/mips/netlogic/common/reset.S b/arch/mips/netlogic/common/reset.S index adb1828..06381e1 100644 --- a/arch/mips/netlogic/common/reset.S +++ b/arch/mips/netlogic/common/reset.S @@ -50,8 +50,8 @@ #include <asm/netlogic/xlp-hal/cpucontrol.h> #define CP0_EBASE $15 -#define SYS_CPU_COHERENT_BASE(node) CKSEG1ADDR(XLP_DEFAULT_IO_BASE) + \ - XLP_IO_SYS_OFFSET(node) + XLP_IO_PCI_HDRSZ + \ +#define SYS_CPU_COHERENT_BASE CKSEG1ADDR(XLP_DEFAULT_IO_BASE) + \ + XLP_IO_SYS_OFFSET(0) + XLP_IO_PCI_HDRSZ + \ SYS_CPU_NONCOHERENT_MODE * 4 /* Enable XLP features and workarounds in the LSU */ @@ -82,26 +82,26 @@ li t1, LSU_DEBUG_ADDR li t2, 0 /* index */ li t3, 0x1000 /* loop count */ -1: +11: sll v0, t2, 5 mtcr zero, t0 ori v1, v0, 0x3 /* way0 | write_enable | write_active */ mtcr v1, t1 -2: +12: mfcr v1, t1 andi v1, 0x1 /* wait for write_active == 0 */ - bnez v1, 2b + bnez v1, 12b nop mtcr zero, t0 ori v1, v0, 0x7 /* way1 | write_enable | write_active */ mtcr v1, t1 -3: +13: mfcr v1, t1 andi v1, 0x1 /* wait for write_active == 0 */ - bnez v1, 3b + bnez v1, 13b nop addi t2, 1 - bne t3, t2, 1b + bne t3, t2, 11b nop .endm @@ -149,7 +149,7 @@ FEXPORT(nlm_reset_entry) li t1, 0x1 sll t0, t1, t0 nor t0, t0, zero /* t0 <- ~(1 << core) */ - li t2, SYS_CPU_COHERENT_BASE(0) + li t2, SYS_CPU_COHERENT_BASE add t2, t2, t3 /* t2 <- SYS offset for node */ lw t1, 0(t2) and t1, t1, t0 @@ -164,8 +164,7 @@ FEXPORT(nlm_reset_entry) /* FALL THROUGH */ /* - * Wake up sibling threads from the initial thread in - * a core. + * Wake up sibling threads from the initial thread in a core. */ EXPORT(nlm_boot_siblings) /* core L1D flush before enable threads */ @@ -181,8 +180,10 @@ EXPORT(nlm_boot_siblings) /* * The new hardware thread starts at the next instruction * For all the cases other than core 0 thread 0, we will - * jump to the secondary wait function. - */ + * jump to the secondary wait function. + + * NOTE: All GPR contents are lost after the mtcr above! + */ mfc0 v0, CP0_EBASE, 1 andi v0, 0x3ff /* v0 <- node/core */ @@ -196,7 +197,7 @@ EXPORT(nlm_boot_siblings) #endif mtc0 t1, CP0_STATUS - /* mark CPU ready, careful here, previous mtcr trashed registers */ + /* mark CPU ready */ li t3, CKSEG1ADDR(RESET_DATA_PHYS) ADDIU t1, t3, BOOT_CPU_READY sll v1, v0, 2 diff --git a/arch/mips/netlogic/common/smpboot.S b/arch/mips/netlogic/common/smpboot.S index aa6cff0..db3b894 100644 --- a/arch/mips/netlogic/common/smpboot.S +++ b/arch/mips/netlogic/common/smpboot.S @@ -98,7 +98,7 @@ END(nlm_boot_secondary_cpus) * In case of RMIboot bootloader which is used on XLR boards, the CPUs * be already woken up and waiting in bootloader code. * This will get them out of the bootloader code and into linux. Needed - * because the bootloader area will be taken and initialized by linux. + * because the bootloader area will be taken and initialized by linux. */ NESTED(nlm_rmiboot_preboot, 16, sp) mfc0 t0, $15, 1 /* read ebase */ @@ -133,6 +133,7 @@ NESTED(nlm_rmiboot_preboot, 16, sp) or t1, t2, v1 /* put in new value */ mtcr t1, t0 /* update core control */ + /* wait for NMI to hit */ 1: wait b 1b nop -- 1.7.9.5
