- Rewrite Alchemy PCI support as a platform driver.
- Fixup boards which have PCI.
Run-tested on DB1500 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@xxxxxxxxxxxxxx>
---
arch/mips/alchemy/common/Makefile | 2 -
arch/mips/alchemy/common/pci.c | 104 -----
arch/mips/alchemy/common/setup.c | 6 +-
arch/mips/alchemy/devboards/db1x00/board_setup.c | 24 -
arch/mips/alchemy/devboards/db1x00/platform.c | 123 +++++
arch/mips/alchemy/devboards/pb1500/board_setup.c | 33 +-
arch/mips/alchemy/devboards/pb1500/platform.c | 48 ++-
arch/mips/alchemy/devboards/pb1550/board_setup.c | 6 -
arch/mips/alchemy/devboards/pb1550/platform.c | 48 ++-
arch/mips/alchemy/gpr/board_setup.c | 12 -
arch/mips/alchemy/gpr/platform.c | 47 ++
arch/mips/alchemy/mtx-1/board_setup.c | 40 --
arch/mips/alchemy/mtx-1/platform.c | 62 +++
arch/mips/alchemy/xxs1500/board_setup.c | 8 -
arch/mips/include/asm/mach-au1x00/au1000.h | 142 ++++--
arch/mips/pci/Makefile | 3 +-
arch/mips/pci/fixup-au1000.c | 43 --
arch/mips/pci/ops-au1000.c | 308 -------------
arch/mips/pci/pci-alchemy.c | 516 ++++++++++++++++++++++
19 files changed, 950 insertions(+), 625 deletions(-)
delete mode 100644 arch/mips/alchemy/common/pci.c
delete mode 100644 arch/mips/pci/fixup-au1000.c
delete mode 100644 arch/mips/pci/ops-au1000.c
create mode 100644 arch/mips/pci/pci-alchemy.c
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile
index 31728e0..3792739 100644
--- a/arch/mips/alchemy/common/Makefile
+++ b/arch/mips/alchemy/common/Makefile
@@ -14,5 +14,3 @@ obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += irq.o
ifeq ($(CONFIG_ALCHEMY_GPIO_INDIRECT),)
obj-$(CONFIG_GPIOLIB) += gpiolib.o
endif
-
-obj-$(CONFIG_PCI) += pci.o
diff --git a/arch/mips/alchemy/common/pci.c b/arch/mips/alchemy/common/pci.c
deleted file mode 100644
index 7866cf5..0000000
--- a/arch/mips/alchemy/common/pci.c
+++ /dev/null
@@ -1,104 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Alchemy/AMD Au1x00 PCI support.
- *
- * Copyright 2001-2003, 2007-2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
- *
- * Copyright (C) 2004 by Ralf Baechle (ralf@xxxxxxxxxxxxxx)
- *
- * Support for all devices (greater than 16) added by David Gathright.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-/* TBD */
-static struct resource pci_io_resource = {
- .start = PCI_IO_START,
- .end = PCI_IO_END,
- .name = "PCI IO space",
- .flags = IORESOURCE_IO
-};
-
-static struct resource pci_mem_resource = {
- .start = PCI_MEM_START,
- .end = PCI_MEM_END,
- .name = "PCI memory space",
- .flags = IORESOURCE_MEM
-};
-
-extern struct pci_ops au1x_pci_ops;
-
-static struct pci_controller au1x_controller = {
- .pci_ops = &au1x_pci_ops,
- .io_resource = &pci_io_resource,
- .mem_resource = &pci_mem_resource,
-};
-
-#if defined(CONFIG_SOC_AU1500) || defined(CONFIG_SOC_AU1550)
-static unsigned long virt_io_addr;
-#endif
-
-static int __init au1x_pci_setup(void)
-{
- extern void au1x_pci_cfg_init(void);
-
-#if defined(CONFIG_SOC_AU1500) || defined(CONFIG_SOC_AU1550)
- virt_io_addr = (unsigned long)ioremap(Au1500_PCI_IO_START,
- Au1500_PCI_IO_END - Au1500_PCI_IO_START + 1);
-
- if (!virt_io_addr) {
- printk(KERN_ERR "Unable to ioremap pci space\n");
- return 1;
- }
- au1x_controller.io_map_base = virt_io_addr;
-
-#ifdef CONFIG_DMA_NONCOHERENT
- {
- /*
- * Set the NC bit in controller for Au1500 pre-AC silicon
- */
- u32 prid = read_c0_prid();
-
- if ((prid & 0xFF000000) == 0x01000000 && prid < 0x01030202) {
- au_writel((1 << 16) | au_readl(Au1500_PCI_CFG),
- Au1500_PCI_CFG);
- printk(KERN_INFO "Non-coherent PCI accesses enabled\n");
- }
- }
-#endif
-
- set_io_port_base(virt_io_addr);
-#endif
-
- au1x_pci_cfg_init();
-
- register_pci_controller(&au1x_controller);
- return 0;
-}
-
-arch_initcall(au1x_pci_setup);
diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
index 1b887c8..37ffd99 100644
--- a/arch/mips/alchemy/common/setup.c
+++ b/arch/mips/alchemy/common/setup.c
@@ -73,8 +73,8 @@ void __init plat_mem_setup(void)
/* This routine should be valid for all Au1x based boards */
phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
{
- u32 start = (u32)Au1500_PCI_MEM_START;
- u32 end = (u32)Au1500_PCI_MEM_END;
+ unsigned long start = ALCHEMY_PCI_MEMWIN_START;
+ unsigned long end = ALCHEMY_PCI_MEMWIN_END;
/* Don't fixup 36-bit addresses */
if ((phys_addr >> 32) != 0)
@@ -82,7 +82,7 @@ phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
/* Check for PCI memory window */
if (phys_addr >= start && (phys_addr + size - 1) <= end)
- return (phys_t)((phys_addr - start) + Au1500_PCI_MEM_START);
+ return (phys_t)(AU1500_PCI_MEM_PHYS_ADDR + phys_addr);
/* default nop */
return phys_addr;
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
index 5c956fe..2b2178f 100644
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ b/arch/mips/alchemy/devboards/db1x00/board_setup.c
@@ -40,24 +40,6 @@
#include <prom.h>
-#ifdef CONFIG_MIPS_DB1500
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - HPT371 */
- [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
-};
-
-#endif
-
-
-#ifdef CONFIG_MIPS_DB1550
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, AU1550_PCI_INTC, 0xff, 0xff, 0xff }, /* IDSEL 11 - on-board HPT371 */
- [12] = { -1, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD, AU1550_PCI_INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, AU1550_PCI_INTA, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-#endif
-
-
#ifdef CONFIG_MIPS_BOSPORUS
char irq_tab_alchemy[][5] __initdata = {
[11] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 11 - miniPCI */
@@ -91,12 +73,6 @@ const char *get_system_type(void)
#ifdef CONFIG_MIPS_MIRAGE
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, AU1500_PCI_INTD, 0xff, 0xff, 0xff }, /* IDSEL 11 - SMI VGX */
- [12] = { -1, 0xff, 0xff, AU1500_PCI_INTC, 0xff }, /* IDSEL 12 - PNX1300 */
- [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 13 - miniPCI */
-};
-
static void mirage_power_off(void)
{
alchemy_gpio_direction_output(210, 1);
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
index 70bcfb5..990367f 100644
--- a/arch/mips/alchemy/devboards/db1x00/platform.c
+++ b/arch/mips/alchemy/devboards/db1x00/platform.c
@@ -25,6 +25,8 @@
#include <asm/mach-db1x00/bcsr.h>
#include "../platform.h"
+struct pci_dev;
+
/* DB1xxx PCMCIA interrupt sources:
* CD0/1 GPIO0/3
* STSCHG0/1 GPIO1/4
@@ -85,6 +87,127 @@
#endif
#endif
+#ifdef CONFIG_PCI
+#ifdef CONFIG_MIPS_DB1500
+static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+#endif
+
+#ifdef CONFIG_MIPS_DB1550
+static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 11) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 11)
+ return (pin == 1) ? AU1550_PCI_INTC : 0xff;
+ if (slot == 12) {
+ switch (pin) {
+ case 1: return AU1550_PCI_INTB;
+ case 2: return AU1550_PCI_INTC;
+ case 3: return AU1550_PCI_INTD;
+ case 4: return AU1550_PCI_INTA;
+ }
+ }
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1550_PCI_INTA;
+ case 2: return AU1550_PCI_INTB;
+ case 3: return AU1550_PCI_INTC;
+ case 4: return AU1550_PCI_INTD;
+ }
+ }
+ return -1;
+}
+#endif
+
+#ifdef CONFIG_MIPS_BOSPORUS
+static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 11) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 11) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ default: return 0xff;
+ }
+ }
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+#endif
+
+#ifdef CONFIG_MIPS_MIRAGE
+static int db1xxx_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 11) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 11)
+ return (pin == 1) ? AU1500_PCI_INTD : 0xff;
+ if (slot == 12)
+ return (pin == 3) ? AU1500_PCI_INTC : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ default: return 0xff;
+ }
+ }
+ return -1;
+}
+#endif
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata db1xxx_pci_pd = {
+ .board_map_irq = db1xxx_map_pci_irq,
+};
+
+static struct platform_device db1xxx_pci_host_dev = {
+ .dev.platform_data = &db1xxx_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+static int __init db15x0_pci_init(void)
+{
+ return platform_device_register(&db1xxx_pci_host_dev);
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(db15x0_pci_init);
+#endif
+
static int __init db1xxx_dev_init(void)
{
#ifdef DB1XXX_HAS_PCMCIA
diff --git a/arch/mips/alchemy/devboards/pb1500/board_setup.c b/arch/mips/alchemy/devboards/pb1500/board_setup.c
index 3b4fa32..37c1883 100644
--- a/arch/mips/alchemy/devboards/pb1500/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1500/board_setup.c
@@ -33,13 +33,6 @@
#include <prom.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - HPT370 */
- [13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
-};
-
-
const char *get_system_type(void)
{
return "Alchemy Pb1500";
@@ -101,20 +94,18 @@ void __init board_setup(void)
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
#ifdef CONFIG_PCI
- /* Setup PCI bus controller */
- au_writel(0, Au1500_PCI_CMEM);
- au_writel(0x00003fff, Au1500_CFG_BASE);
-#if defined(__MIPSEB__)
- au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
-#else
- au_writel(0xf, Au1500_PCI_CFG);
-#endif
- au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV);
- au_writel(0, Au1500_PCI_MWBASE_REV_CCL);
- au_writel(0x02a00356, Au1500_PCI_STATCMD);
- au_writel(0x00003c04, Au1500_PCI_HDRTYPE);
- au_writel(0x00000008, Au1500_PCI_MBAR);
- au_sync();
+ {
+ void __iomem *base =
+ (void __iomem *)KSEG1ADDR(AU1500_PCI_PHYS_ADDR);
+ /* Setup PCI bus controller */
+ __raw_writel(0x00003fff, base + PCI_REG_CMEM);
+ __raw_writel(0xf0000000, base + PCI_REG_MWMASK_DEV);
+ __raw_writel(0, base + PCI_REG_MWBASE_REV_CCL);
+ __raw_writel(0x02a00356, base + PCI_REG_STATCMD);
+ __raw_writel(0x00003c04, base + PCI_REG_PARAM);
+ __raw_writel(0x00000008, base + PCI_REG_MBAR);
+ wmb();
+ }
#endif
/* Enable sys bus clock divider when IDLE state or no bus activity. */
diff --git a/arch/mips/alchemy/devboards/pb1500/platform.c b/arch/mips/alchemy/devboards/pb1500/platform.c
index 42b0e6b..9f0b5a0 100644
--- a/arch/mips/alchemy/devboards/pb1500/platform.c
+++ b/arch/mips/alchemy/devboards/pb1500/platform.c
@@ -19,11 +19,56 @@
*/
#include <linux/init.h>
+#include <linux/platform_device.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-db1x00/bcsr.h>
#include "../platform.h"
+static int pb1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12)
+ return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1500_pci_pd = {
+ .board_map_irq = pb1500_map_pci_irq,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device pb1500_pci_host = {
+ .dev.platform_data = &pb1500_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
static int __init pb1500_dev_init(void)
{
int swapped;
@@ -41,7 +86,8 @@ static int __init pb1500_dev_init(void)
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT;
db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1500_pci_host);
return 0;
}
-device_initcall(pb1500_dev_init);
+arch_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550/board_setup.c b/arch/mips/alchemy/devboards/pb1550/board_setup.c
index b790213..0f62d1e 100644
--- a/arch/mips/alchemy/devboards/pb1550/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1550/board_setup.c
@@ -37,12 +37,6 @@
#include <prom.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD, AU1550_PCI_INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, AU1550_PCI_INTA, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-
const char *get_system_type(void)
{
return "Alchemy Pb1550";
diff --git a/arch/mips/alchemy/devboards/pb1550/platform.c b/arch/mips/alchemy/devboards/pb1550/platform.c
index 87c79b7..0c5711f 100644
--- a/arch/mips/alchemy/devboards/pb1550/platform.c
+++ b/arch/mips/alchemy/devboards/pb1550/platform.c
@@ -19,13 +19,56 @@
*/
#include <linux/init.h>
-
+#include <linux/platform_device.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1550.h>
#include <asm/mach-db1x00/bcsr.h>
#include "../platform.h"
+static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot < 12) || (slot > 13) || pin == 0)
+ return -1;
+ if (slot == 12) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTB;
+ case 2: return AU1500_PCI_INTC;
+ case 3: return AU1500_PCI_INTD;
+ case 4: return AU1500_PCI_INTA;
+ }
+ }
+ if (slot == 13) {
+ switch (pin) {
+ case 1: return AU1500_PCI_INTA;
+ case 2: return AU1500_PCI_INTB;
+ case 3: return AU1500_PCI_INTC;
+ case 4: return AU1500_PCI_INTD;
+ }
+ }
+ return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct alchemy_pci_platdata pb1550_pci_pd = {
+ .board_map_irq = pb1550_map_pci_irq,
+};
+
+static struct platform_device pb1550_pci_host = {
+ .dev.platform_data = &pb1550_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
static int __init pb1550_dev_init(void)
{
int swapped;
@@ -57,7 +100,8 @@ static int __init pb1550_dev_init(void)
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
+ platform_device_register(&pb1550_pci_host);
return 0;
}
-device_initcall(pb1550_dev_init);
+arch_initcall(pb1550_dev_init);
diff --git a/arch/mips/alchemy/gpr/board_setup.c b/arch/mips/alchemy/gpr/board_setup.c
index 5f8f069..dea45c7 100644
--- a/arch/mips/alchemy/gpr/board_setup.c
+++ b/arch/mips/alchemy/gpr/board_setup.c
@@ -36,10 +36,6 @@
#include <prom.h>
-char irq_tab_alchemy[][5] __initdata = {
- [0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff },
-};
-
static void gpr_reset(char *c)
{
/* switch System-LED to orange (red# and green# on) */
@@ -76,12 +72,4 @@ void __init board_setup(void)
/* Take away Reset of UMTS-card */
alchemy_gpio_direction_output(215, 1);
-
-#ifdef CONFIG_PCI
-#if defined(__MIPSEB__)
- au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
-#else
- au_writel(0xf, Au1500_PCI_CFG);
-#endif
-#endif
}
diff --git a/arch/mips/alchemy/gpr/platform.c b/arch/mips/alchemy/gpr/platform.c
index 14b4662..982ce85 100644
--- a/arch/mips/alchemy/gpr/platform.c
+++ b/arch/mips/alchemy/gpr/platform.c
@@ -167,6 +167,45 @@ static struct i2c_board_info gpr_i2c_info[] __initdata = {
}
};
+
+
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static int gpr_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ if ((slot == 0) && (pin == 1))
+ return AU1550_PCI_INTA;
+ else if ((slot == 0) && (pin == 2))
+ return AU1550_PCI_INTB;
+
+ return -1;
+}
+
+static struct alchemy_pci_platdata gpr_pci_pd = {
+ .board_map_irq = gpr_map_pci_irq,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device gpr_pci_host_dev = {
+ .dev.platform_data = &gpr_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
static struct platform_device *gpr_devices[] __initdata = {
&gpr_wdt_device,
&gpr_mtd_device,
@@ -174,6 +213,14 @@ static struct platform_device *gpr_devices[] __initdata = {
&gpr_led_devices,
};
+static int __init gpr_pci_init(void)
+{
+ return platform_device_register(&gpr_pci_host_dev);
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(gpr_pci_init);
+
+
static int __init gpr_dev_init(void)
{
i2c_register_board_info(0, gpr_i2c_info, ARRAY_SIZE(gpr_i2c_info));
diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
index 3ae984c..851a5ab 100644
--- a/arch/mips/alchemy/mtx-1/board_setup.c
+++ b/arch/mips/alchemy/mtx-1/board_setup.c
@@ -38,20 +38,6 @@
#include <prom.h>
-char irq_tab_alchemy[][5] __initdata = {
- [0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
- [1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
- [2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
- [3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
- [4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
- [5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
- [6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
- [7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
-};
-
-extern int (*board_pci_idsel)(unsigned int devsel, int assert);
-int mtx1_pci_idsel(unsigned int devsel, int assert);
-
static void mtx1_reset(char *c)
{
/* Jump to the reset vector */
@@ -74,15 +60,6 @@ void __init board_setup(void)
alchemy_gpio_direction_output(204, 0);
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-#ifdef CONFIG_PCI
-#if defined(__MIPSEB__)
- au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
-#else
- au_writel(0xf, Au1500_PCI_CFG);
-#endif
- board_pci_idsel = mtx1_pci_idsel;
-#endif
-
/* Initialize sys_pinfunc */
au_writel(SYS_PF_NI2, SYS_PINFUNC);
@@ -104,23 +81,6 @@ void __init board_setup(void)
printk(KERN_INFO "4G Systems MTX-1 Board\n");
}
-int
-mtx1_pci_idsel(unsigned int devsel, int assert)
-{
- /* This function is only necessary to support a proprietary Cardbus
- * adapter on the mtx-1 "singleboard" variant. It triggers a custom
- * logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals.
- */
- if (assert && devsel != 0)
- /* Suppress signal to Cardbus */
- alchemy_gpio_set_value(1, 0); /* set EXT_IO3 OFF */
- else
- alchemy_gpio_set_value(1, 1); /* set EXT_IO3 ON */
-
- udelay(1);
- return 1;
-}
-
static int __init mtx1_init_irq(void)
{
irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
diff --git a/arch/mips/alchemy/mtx-1/platform.c b/arch/mips/alchemy/mtx-1/platform.c
index 55628e3..cc47b68 100644
--- a/arch/mips/alchemy/mtx-1/platform.c
+++ b/arch/mips/alchemy/mtx-1/platform.c
@@ -135,7 +135,69 @@ static struct platform_device mtx1_mtd = {
.resource = &mtx1_mtd_resource,
};
+static struct resource alchemy_pci_host_res[] = {
+ [0] = {
+ .start = AU1500_PCI_PHYS_ADDR,
+ .end = AU1500_PCI_PHYS_ADDR + 0xfff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static int mtx1_pci_idsel(unsigned int devsel, int assert)
+{
+ /* This function is only necessary to support a proprietary Cardbus
+ * adapter on the mtx-1 "singleboard" variant. It triggers a custom
+ * logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals.
+ */
+ if (assert && devsel != 0)
+ /* Suppress signal to Cardbus */
+ alchemy_gpio_set_value(1, 0); /* set EXT_IO3 OFF */
+ else
+ alchemy_gpio_set_value(1, 1); /* set EXT_IO3 ON */
+
+ udelay(1);
+ return 1;
+}
+
+static const char mtx1_irqtab[][5] = {
+ [0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
+ [1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
+ [2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
+ [3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
+ [4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
+ [5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
+ [6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
+ [7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
+};
+
+static int mtx1_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+ return mtx1_irqtab[slot][pin];
+}
+
+static struct alchemy_pci_platdata mtx1_pci_pd = {
+ .board_map_irq = mtx1_map_pci_irq,
+ .board_pci_idsel = mtx1_pci_idsel,
+ .pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+ PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+ PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+ 0,
+#endif
+};
+
+static struct platform_device mtx1_pci_host = {
+ .dev.platform_data = &mtx1_pci_pd,
+ .name = "alchemy-pci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
+ .resource = alchemy_pci_host_res,
+};
+
+
static struct __initdata platform_device * mtx1_devs[] = {
+ &mtx1_pci_host,
&mtx1_gpio_leds,
&mtx1_wdt,
&mtx1_button,
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index 81e57fa..3fa83f7 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -70,14 +70,6 @@ void __init board_setup(void)
/* Enable DTR (MCR bit 0) = USB power up */
__raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
wmb();
-
-#ifdef CONFIG_PCI
-#if defined(__MIPSEB__)
- au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
-#else
- au_writel(0xf, Au1500_PCI_CFG);
-#endif
-#endif
}
static int __init xxs1500_init_irq(void)
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index bcf3d1e..5da2fd7 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -254,6 +254,14 @@ enum alchemy_usb_block {
};
int alchemy_usb_control(int block, int enable);
+/* PCI controller platform data */
+struct alchemy_pci_platdata {
+ int (*board_map_irq)(const struct pci_dev *d, u8 slot, u8 pin);
+ int (*board_pci_idsel)(unsigned int devsel, int assert);
+ /* bits to set/clear in PCI_CONFIG register */
+ unsigned long pci_cfg_set;
+ unsigned long pci_cfg_clr;
+};
/* SOC Interrupt numbers */
@@ -1309,58 +1317,30 @@ enum soc_au1200_ints {
# define AC97C_RS (1 << 1)
# define AC97C_CE (1 << 0)
-#if defined(CONFIG_SOC_AU1500) || defined(CONFIG_SOC_AU1550)
-/* Au1500 PCI Controller */
-#define Au1500_CFG_BASE 0xB4005000 /* virtual, KSEG1 addr */
-#define Au1500_PCI_CMEM (Au1500_CFG_BASE + 0)
-#define Au1500_PCI_CFG (Au1500_CFG_BASE + 4)
-# define PCI_ERROR ((1 << 22) | (1 << 23) | (1 << 24) | \
- (1 << 25) | (1 << 26) | (1 << 27))
-#define Au1500_PCI_B2BMASK_CCH (Au1500_CFG_BASE + 8)
-#define Au1500_PCI_B2B0_VID (Au1500_CFG_BASE + 0xC)
-#define Au1500_PCI_B2B1_ID (Au1500_CFG_BASE + 0x10)
-#define Au1500_PCI_MWMASK_DEV (Au1500_CFG_BASE + 0x14)
-#define Au1500_PCI_MWBASE_REV_CCL (Au1500_CFG_BASE + 0x18)
-#define Au1500_PCI_ERR_ADDR (Au1500_CFG_BASE + 0x1C)
-#define Au1500_PCI_SPEC_INTACK (Au1500_CFG_BASE + 0x20)
-#define Au1500_PCI_ID (Au1500_CFG_BASE + 0x100)
-#define Au1500_PCI_STATCMD (Au1500_CFG_BASE + 0x104)
-#define Au1500_PCI_CLASSREV (Au1500_CFG_BASE + 0x108)
-#define Au1500_PCI_HDRTYPE (Au1500_CFG_BASE + 0x10C)
-#define Au1500_PCI_MBAR (Au1500_CFG_BASE + 0x110)
-
-#define Au1500_PCI_HDR 0xB4005100 /* virtual, KSEG1 addr */
-/*
- * All of our structures, like PCI resource, have 32-bit members.
- * Drivers are expected to do an ioremap on the PCI MEM resource, but it's
- * hard to store 0x4 0000 0000 in a 32-bit type. We require a small patch
- * to __ioremap to check for addresses between (u32)Au1500_PCI_MEM_START and
- * (u32)Au1500_PCI_MEM_END and change those to the full 36-bit PCI MEM
- * addresses. For PCI I/O, it's simpler because we get to do the ioremap
- * ourselves and then adjust the device's resources.
+/* The PCI chip selects are outside the 32bit space, and since we can't
+ * just program the 36bit addresses into BARs, we have to take a chunk
+ * out of the 32bit space and reserve it for PCI. When these addresses
+ * are ioremap()ed, they'll be fixed up to the real 36bit address before
+ * being passed to the real ioremap function.
*/
-#define Au1500_EXT_CFG 0x600000000ULL
-#define Au1500_EXT_CFG_TYPE1 0x680000000ULL
-#define Au1500_PCI_IO_START 0x500000000ULL
-#define Au1500_PCI_IO_END 0x5000FFFFFULL
-#define Au1500_PCI_MEM_START 0x440000000ULL
-#define Au1500_PCI_MEM_END 0x44FFFFFFFULL
+#define ALCHEMY_PCI_MEMWIN_START (AU1500_PCI_MEM_PHYS_ADDR >> 4)
+#define ALCHEMY_PCI_MEMWIN_END (ALCHEMY_PCI_MEMWIN_START + 0x0FFFFFFF)
-#define PCI_IO_START 0x00001000
-#define PCI_IO_END 0x000FFFFF
-#define PCI_MEM_START 0x40000000
-#define PCI_MEM_END 0x4FFFFFFF
+/* for PCI IO it's simpler because we get to do the ioremap ourselves and then
+ * adjust the device's resources.
+ */
+#define ALCHEMY_PCI_IOWIN_START 0x00001000
+#define ALCHEMY_PCI_IOWIN_END 0x0000FFFF
-#define PCI_FIRST_DEVFN (0 << 3)
-#define PCI_LAST_DEVFN (19 << 3)
+#ifdef CONFIG_PCI
#define IOPORT_RESOURCE_START 0x00001000 /* skip legacy probing */
#define IOPORT_RESOURCE_END 0xffffffff
#define IOMEM_RESOURCE_START 0x10000000
#define IOMEM_RESOURCE_END 0xfffffffffULL
-#else /* Au1000 and Au1100 and Au1200 */
+#else
/* Don't allow any legacy ports probing */
#define IOPORT_RESOURCE_START 0x10000000
@@ -1368,13 +1348,77 @@ enum soc_au1200_ints {
#define IOMEM_RESOURCE_START 0x10000000
#define IOMEM_RESOURCE_END 0xfffffffffULL
-#define PCI_IO_START 0
-#define PCI_IO_END 0
-#define PCI_MEM_START 0
-#define PCI_MEM_END 0
-#define PCI_FIRST_DEVFN 0
-#define PCI_LAST_DEVFN 0
-
#endif
+/* PCI controller block register offsets */
+#define PCI_REG_CMEM 0x0000
+#define PCI_REG_CONFIG 0x0004
+#define PCI_REG_B2BMASK_CCH 0x0008
+#define PCI_REG_B2BBASE0_VID 0x000C
+#define PCI_REG_B2BBASE1_SID 0x0010
+#define PCI_REG_MWMASK_DEV 0x0014
+#define PCI_REG_MWBASE_REV_CCL 0x0018
+#define PCI_REG_ERR_ADDR 0x001C
+#define PCI_REG_SPEC_INTACK 0x0020
+#define PCI_REG_ID 0x0100
+#define PCI_REG_STATCMD 0x0104
+#define PCI_REG_CLASSREV 0x0108
+#define PCI_REG_PARAM 0x010C
+#define PCI_REG_MBAR 0x0110
+#define PCI_REG_TIMEOUT 0x0140
+
+/* PCI controller block register bits */
+#define PCI_CMEM_E (1 << 28) /* enable cacheable memory */
+#define PCI_CMEM_CMBASE(x) (((x) & 0x3fff) << 14)
+#define PCI_CMEM_CMMASK(x) ((x) & 0x3fff)
+#define PCI_CONFIG_ERD (1 << 27) /* pci error during R/W */
+#define PCI_CONFIG_ET (1 << 26) /* error in target mode */
+#define PCI_CONFIG_EF (1 << 25) /* fatal error */
+#define PCI_CONFIG_EP (1 << 24) /* parity error */
+#define PCI_CONFIG_EM (1 << 23) /* multiple errors */
+#define PCI_CONFIG_BM (1 << 22) /* bad master error */
+#define PCI_CONFIG_PD (1 << 20) /* PCI Disable */
+#define PCI_CONFIG_BME (1 << 19) /* Byte Mask Enable for reads */
+#define PCI_CONFIG_NC (1 << 16) /* mark mem access non-coherent */
+#define PCI_CONFIG_IA (1 << 15) /* INTA# enabled (target mode) */
+#define PCI_CONFIG_IP (1 << 13) /* int on PCI_PERR# */
+#define PCI_CONFIG_IS (1 << 12) /* int on PCI_SERR# */
+#define PCI_CONFIG_IMM (1 << 11) /* int on master abort */
+#define PCI_CONFIG_ITM (1 << 10) /* int on target abort (as master) */
+#define PCI_CONFIG_ITT (1 << 9) /* int on target abort (as target) */
+#define PCI_CONFIG_IPB (1 << 8) /* int on PERR# in bus master acc */
+#define PCI_CONFIG_SIC_NO (0 << 6) /* no byte mask changes */
+#define PCI_CONFIG_SIC_BA_ADR (1 << 6) /* on byte/hw acc, invert adr bits */
+#define PCI_CONFIG_SIC_HWA_DAT (2 << 6) /* on halfword acc, swap data */
+#define PCI_CONFIG_SIC_ALL (3 << 6) /* swap data bytes on all accesses */
+#define PCI_CONFIG_ST (1 << 5) /* swap data by target transactions */
+#define PCI_CONFIG_SM (1 << 4) /* swap data from PCI ctl */
+#define PCI_CONFIG_AEN (1 << 3) /* enable internal arbiter */
+#define PCI_CONFIG_R2H (1 << 2) /* REQ2# to hi-prio arbiter */
+#define PCI_CONFIG_R1H (1 << 1) /* REQ1# to hi-prio arbiter */
+#define PCI_CONFIG_CH (1 << 0) /* PCI ctl to hi-prio arbiter */
+#define PCI_B2BMASK_B2BMASK(x) (((x) & 0xffff) << 16)
+#define PCI_B2BMASK_CCH(x) ((x) & 0xffff) /* 16 upper bits of class code */
+#define PCI_B2BBASE0_VID_B0(x) (((x) & 0xffff) << 16)
+#define PCI_B2BBASE0_VID_SV(x) ((x) & 0xffff)
+#define PCI_B2BBASE1_SID_B1(x) (((x) & 0xffff) << 16)
+#define PCI_B2BBASE1_SID_SI(x) ((x) & 0xffff)
+#define PCI_MWMASKDEV_MWMASK(x) (((x) & 0xffff) << 16)
+#define PCI_MWMASKDEV_DEVID(x) ((x) & 0xffff)
+#define PCI_MWBASEREVCCL_BASE(x) (((x) & 0xffff) << 16)
+#define PCI_MWBASEREVCCL_REV(x) (((x) & 0xff) << 8)
+#define PCI_MWBASEREVCCL_CCL(x) ((x) & 0xff)
+#define PCI_ID_DID(x) (((x) & 0xffff) << 16)
+#define PCI_ID_VID(x) ((x) & 0xffff)
+#define PCI_STATCMD_STATUS(x) (((x) & 0xffff) << 16)
+#define PCI_STATCMD_CMD(x) ((x) & 0xffff)
+#define PCI_CLASSREV_CLASS(x) (((x) & 0x00ffffff) << 8)
+#define PCI_CLASSREV_REV(x) ((x) & 0xff)
+#define PCI_PARAM_BIST(x) (((x) & 0xff) << 24)
+#define PCI_PARAM_HT(x) (((x) & 0xff) << 16)
+#define PCI_PARAM_LT(x) (((x) & 0xff) << 8)
+#define PCI_PARAM_CLS(x) ((x) & 0xff)
+#define PCI_TIMEOUT_RETRIES(x) (((x) & 0xff) << 8) /* max retries */
+#define PCI_TIMEOUT_TO(x) ((x) & 0xff) /* target ready timeout */
+
#endif
diff --git a/arch/mips/pci/Makefile b/arch/mips/pci/Makefile
index 4df8799..bb82cbd 100644
--- a/arch/mips/pci/Makefile
+++ b/arch/mips/pci/Makefile
@@ -18,14 +18,13 @@ obj-$(CONFIG_PCI_TX4927) += ops-tx4927.o
obj-$(CONFIG_BCM47XX) += pci-bcm47xx.o
obj-$(CONFIG_BCM63XX) += pci-bcm63xx.o fixup-bcm63xx.o \
ops-bcm63xx.o
+obj-$(CONFIG_MIPS_ALCHEMY) += pci-alchemy.o
#
# These are still pretty much in the old state, watch, go blind.
#
obj-$(CONFIG_LASAT) += pci-lasat.o
obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o
-obj-$(CONFIG_SOC_AU1500) += fixup-au1000.o ops-au1000.o
-obj-$(CONFIG_SOC_AU1550) += fixup-au1000.o ops-au1000.o
obj-$(CONFIG_SOC_PNX8550) += fixup-pnx8550.o ops-pnx8550.o
obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-loongson2.o
obj-$(CONFIG_LEMOTE_MACH2F) += fixup-lemote2f.o ops-loongson2.o
diff --git a/arch/mips/pci/fixup-au1000.c b/arch/mips/pci/fixup-au1000.c
deleted file mode 100644
index e2ddfc4..0000000
--- a/arch/mips/pci/fixup-au1000.c
+++ /dev/null
@@ -1,43 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Board specific PCI fixups.
- *
- * Copyright 2001-2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/pci.h>
-#include <linux/init.h>
-
-extern char irq_tab_alchemy[][5];
-
-int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- return irq_tab_alchemy[slot][pin];
-}
-
-/* Do platform specific device initialization at pci_enable_device() time */
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
- return 0;
-}
diff --git a/arch/mips/pci/ops-au1000.c b/arch/mips/pci/ops-au1000.c
deleted file mode 100644
index 9a57c5a..0000000
--- a/arch/mips/pci/ops-au1000.c
+++ /dev/null
@@ -1,308 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Alchemy/AMD Au1xx0 PCI support.
- *
- * Copyright 2001-2003, 2007-2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
- *
- * Support for all devices (greater than 16) added by David Gathright.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/vmalloc.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#undef DEBUG
-#ifdef DEBUG
-#define DBG(x...) printk(KERN_DEBUG x)
-#else
-#define DBG(x...)
-#endif
-
-#define PCI_ACCESS_READ 0
-#define PCI_ACCESS_WRITE 1
-
-int (*board_pci_idsel)(unsigned int devsel, int assert);
-
-void mod_wired_entry(int entry, unsigned long entrylo0,
- unsigned long entrylo1, unsigned long entryhi,
- unsigned long pagemask)
-{
- unsigned long old_pagemask;
- unsigned long old_ctx;
-
- /* Save old context and create impossible VPN2 value */
- old_ctx = read_c0_entryhi() & 0xff;
- old_pagemask = read_c0_pagemask();
- write_c0_index(entry);
- write_c0_pagemask(pagemask);
- write_c0_entryhi(entryhi);
- write_c0_entrylo0(entrylo0);
- write_c0_entrylo1(entrylo1);
- tlb_write_indexed();
- write_c0_entryhi(old_ctx);
- write_c0_pagemask(old_pagemask);
-}
-
-static struct vm_struct *pci_cfg_vm;
-static int pci_cfg_wired_entry;
-static unsigned long last_entryLo0, last_entryLo1;
-
-/*
- * We can't ioremap the entire pci config space because it's too large.
- * Nor can we call ioremap dynamically because some device drivers use
- * the PCI config routines from within interrupt handlers and that
- * becomes a problem in get_vm_area(). We use one wired TLB to handle
- * all config accesses for all busses.
- */
-void __init au1x_pci_cfg_init(void)
-{
- /* Reserve a wired entry for PCI config accesses */
- pci_cfg_vm = get_vm_area(0x2000, VM_IOREMAP);
- if (!pci_cfg_vm)
- panic(KERN_ERR "PCI unable to get vm area\n");
- pci_cfg_wired_entry = read_c0_wired();
- add_wired_entry(0, 0, (unsigned long)pci_cfg_vm->addr, PM_4K);
- last_entryLo0 = last_entryLo1 = 0xffffffff;
-}
-
-static int config_access(unsigned char access_type, struct pci_bus *bus,
- unsigned int dev_fn, unsigned char where, u32 *data)
-{
-#if defined(CONFIG_SOC_AU1500) || defined(CONFIG_SOC_AU1550)
- unsigned int device = PCI_SLOT(dev_fn);
- unsigned int function = PCI_FUNC(dev_fn);
- unsigned long offset, status;
- unsigned long cfg_base;
- unsigned long flags;
- int error = PCIBIOS_SUCCESSFUL;
- unsigned long entryLo0, entryLo1;
-
- if (device > 19) {
- *data = 0xffffffff;
- return -1;
- }
-
- local_irq_save(flags);
- au_writel(((0x2000 << 16) | (au_readl(Au1500_PCI_STATCMD) & 0xffff)),
- Au1500_PCI_STATCMD);
- au_sync_udelay(1);
-
- /*
- * Allow board vendors to implement their own off-chip IDSEL.
- * If it doesn't succeed, may as well bail out at this point.
- */
- if (board_pci_idsel && board_pci_idsel(device, 1) == 0) {
- *data = 0xffffffff;
- local_irq_restore(flags);
- return -1;
- }
-
- /* Setup the config window */
- if (bus->number == 0)
- cfg_base = (1 << device) << 11;
- else
- cfg_base = 0x80000000 | (bus->number << 16) | (device << 11);
-
- /* Setup the lower bits of the 36-bit address */
- offset = (function << 8) | (where & ~0x3);
- /* Pick up any address that falls below the page mask */
- offset |= cfg_base & ~PAGE_MASK;
-
- /* Page boundary */
- cfg_base = cfg_base & PAGE_MASK;
-
- /*
- * To improve performance, if the current device is the same as
- * the last device accessed, we don't touch the TLB.
- */
- entryLo0 = (6 << 26) | (cfg_base >> 6) | (2 << 3) | 7;
- entryLo1 = (6 << 26) | (cfg_base >> 6) | (0x1000 >> 6) | (2 << 3) | 7;
- if ((entryLo0 != last_entryLo0) || (entryLo1 != last_entryLo1)) {
- mod_wired_entry(pci_cfg_wired_entry, entryLo0, entryLo1,
- (unsigned long)pci_cfg_vm->addr, PM_4K);
- last_entryLo0 = entryLo0;
- last_entryLo1 = entryLo1;
- }
-
- if (access_type == PCI_ACCESS_WRITE)
- au_writel(*data, (int)(pci_cfg_vm->addr + offset));
- else
- *data = au_readl((int)(pci_cfg_vm->addr + offset));
-
- au_sync_udelay(2);
-
- DBG("cfg_access %d bus->number %u dev %u at %x *data %x conf %lx\n",
- access_type, bus->number, device, where, *data, offset);
-
- /* Check master abort */
- status = au_readl(Au1500_PCI_STATCMD);
-
- if (status & (1 << 29)) {
- *data = 0xffffffff;
- error = -1;
- DBG("Au1x Master Abort\n");
- } else if ((status >> 28) & 0xf) {
- DBG("PCI ERR detected: device %u, status %lx\n",
- device, (status >> 28) & 0xf);
-
- /* Clear errors */
- au_writel(status & 0xf000ffff, Au1500_PCI_STATCMD);
-
- *data = 0xffffffff;
- error = -1;
- }
-
- /* Take away the IDSEL. */
- if (board_pci_idsel)
- (void)board_pci_idsel(device, 0);
-
- local_irq_restore(flags);
- return error;
-#endif
-}
-
-static int read_config_byte(struct pci_bus *bus, unsigned int devfn,
- int where, u8 *val)
-{
- u32 data;
- int ret;
-
- ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
- if (where & 1)
- data >>= 8;
- if (where & 2)
- data >>= 16;
- *val = data & 0xff;
- return ret;
-}
-
-static int read_config_word(struct pci_bus *bus, unsigned int devfn,
- int where, u16 *val)
-{
- u32 data;
- int ret;
-
- ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
- if (where & 2)
- data >>= 16;
- *val = data & 0xffff;
- return ret;
-}
-
-static int read_config_dword(struct pci_bus *bus, unsigned int devfn,
- int where, u32 *val)
-{
- int ret;
-
- ret = config_access(PCI_ACCESS_READ, bus, devfn, where, val);
- return ret;
-}
-
-static int write_config_byte(struct pci_bus *bus, unsigned int devfn,
- int where, u8 val)
-{
- u32 data = 0;
-
- if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
- return -1;
-
- data = (data & ~(0xff << ((where & 3) << 3))) |
- (val << ((where & 3) << 3));
-
- if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
- return -1;
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int write_config_word(struct pci_bus *bus, unsigned int devfn,
- int where, u16 val)
-{
- u32 data = 0;
-
- if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
- return -1;
-
- data = (data & ~(0xffff << ((where & 3) << 3))) |
- (val << ((where & 3) << 3));
-
- if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
- return -1;
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int write_config_dword(struct pci_bus *bus, unsigned int devfn,
- int where, u32 val)
-{
- if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &val))
- return -1;
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int config_read(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 *val)
-{
- switch (size) {
- case 1: {
- u8 _val;
- int rc = read_config_byte(bus, devfn, where, &_val);
-
- *val = _val;
- return rc;
- }
- case 2: {
- u16 _val;
- int rc = read_config_word(bus, devfn, where, &_val);
-
- *val = _val;
- return rc;
- }
- default:
- return read_config_dword(bus, devfn, where, val);
- }
-}
-
-static int config_write(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 val)
-{
- switch (size) {
- case 1:
- return write_config_byte(bus, devfn, where, (u8) val);
- case 2:
- return write_config_word(bus, devfn, where, (u16) val);
- default:
- return write_config_dword(bus, devfn, where, val);
- }
-}
-
-struct pci_ops au1x_pci_ops = {
- config_read,
- config_write
-};
diff --git a/arch/mips/pci/pci-alchemy.c b/arch/mips/pci/pci-alchemy.c
new file mode 100644
index 0000000..4ee5710
--- /dev/null
+++ b/arch/mips/pci/pci-alchemy.c
@@ -0,0 +1,516 @@
+/*
+ * Alchemy PCI host mode support.
+ *
+ * Copyright 2001-2003, 2007-2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@xxxxxxxxxx>
+ *
+ * Support for all devices (greater than 16) added by David Gathright.
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/vmalloc.h>
+
+#include <asm/mach-au1x00/au1000.h>
+
+#ifdef CONFIG_DEBUG_PCI
+#define DBG(x...) printk(KERN_DEBUG x)
+#else
+#define DBG(x...) do {} while (0)
+#endif
+
+#define PCI_ACCESS_READ 0
+#define PCI_ACCESS_WRITE 1
+
+struct alchemy_pci_context {
+ struct pci_controller alchemy_pci_ctrl; /* leave as first member! */
+ void __iomem *regs; /* ctrl base */
+ /* tools for wired entry for config space access */
+ unsigned long last_elo0;
+ unsigned long last_elo1;
+ int wired_entry;
+ struct vm_struct *pci_cfg_vm;
+
+ unsigned long pm[12];
+
+ int (*board_map_irq)(const struct pci_dev *d, u8 slot, u8 pin);
+ int (*board_pci_idsel)(unsigned int devsel, int assert);
+};
+
+/* IO/MEM resources for PCI. Keep the memres in sync with __fixup_bigphys_addr
+ * in arch/mips/alchemy/common/setup.c
+ */
+static struct resource alchemy_pci_def_memres = {
+ .start = ALCHEMY_PCI_MEMWIN_START,
+ .end = ALCHEMY_PCI_MEMWIN_END,
+ .name = "PCI memory space",
+ .flags = IORESOURCE_MEM
+};
+
+static struct resource alchemy_pci_def_iores = {
+ .start = ALCHEMY_PCI_IOWIN_START,
+ .end = ALCHEMY_PCI_IOWIN_END,
+ .name = "PCI IO space",
+ .flags = IORESOURCE_IO
+};
+
+static void mod_wired_entry(int entry, unsigned long entrylo0,
+ unsigned long entrylo1, unsigned long entryhi,
+ unsigned long pagemask)
+{
+ unsigned long old_pagemask;
+ unsigned long old_ctx;
+
+ /* Save old context and create impossible VPN2 value */
+ old_ctx = read_c0_entryhi() & 0xff;
+ old_pagemask = read_c0_pagemask();
+ write_c0_index(entry);
+ write_c0_pagemask(pagemask);
+ write_c0_entryhi(entryhi);
+ write_c0_entrylo0(entrylo0);
+ write_c0_entrylo1(entrylo1);
+ tlb_write_indexed();
+ write_c0_entryhi(old_ctx);
+ write_c0_pagemask(old_pagemask);
+}
+
+static void alchemy_pci_wired_entry(struct alchemy_pci_context *ctx)
+{
+ ctx->wired_entry = read_c0_wired();
+ add_wired_entry(0, 0, (unsigned long)ctx->pci_cfg_vm->addr, PM_4K);
+ ctx->last_elo0 = ctx->last_elo1 = ~0;
+}
+
+static int config_access(unsigned char access_type, struct pci_bus *bus,
+ unsigned int dev_fn, unsigned char where, u32 *data)
+{
+ struct alchemy_pci_context *ctx = bus->sysdata;
+ unsigned int device = PCI_SLOT(dev_fn);
+ unsigned int function = PCI_FUNC(dev_fn);
+ unsigned long offset, status, cfg_base, flags, entryLo0, entryLo1, r;
+ int error = PCIBIOS_SUCCESSFUL;
+
+ if (device > 19) {
+ *data = 0xffffffff;
+ return -1;
+ }
+
+ /* YAMON on all db1xxx boards wipes the TLB and writes zero to C0_wired
+ * on resume, clearing our wired entry. Unfortunately the ->resume()
+ * callback is called way way way too late (and ->suspend() too early)
+ * to have them destroy and recreate it. Instead just test if c0_wired
+ * is now lower than the index we retrieved before suspending and then
+ * recreate the entry if necessary. Of course this is totally bonkers
+ * and breaks as soon as someone else adds another wired entry somewhere
+ * else. Anyone have any ideas how to handle this better?
+ */
+ if (unlikely(read_c0_wired() < ctx->wired_entry))
+ alchemy_pci_wired_entry(ctx);
+
+ local_irq_save(flags);
+ r = __raw_readl(ctx->regs + PCI_REG_STATCMD) & 0x0000ffff;
+ r |= PCI_STATCMD_STATUS(0x2000);
+ __raw_writel(r, ctx->regs + PCI_REG_STATCMD);
+ wmb();
+
+ /* Allow board vendors to implement their own off-chip IDSEL.
+ * If it doesn't succeed, may as well bail out at this point.
+ */
+ if (ctx->board_pci_idsel(device, 1) == 0) {
+ *data = 0xffffffff;
+ local_irq_restore(flags);
+ return -1;
+ }
+
+ /* Setup the config window */
+ if (bus->number == 0)
+ cfg_base = (1 << device) << 11;
+ else
+ cfg_base = 0x80000000 | (bus->number << 16) | (device << 11);
+
+ /* Setup the lower bits of the 36-bit address */
+ offset = (function << 8) | (where & ~0x3);
+ /* Pick up any address that falls below the page mask */
+ offset |= cfg_base & ~PAGE_MASK;
+
+ /* Page boundary */
+ cfg_base = cfg_base & PAGE_MASK;
+
+ /* To improve performance, if the current device is the same as
+ * the last device accessed, we don't touch the TLB.
+ */
+ entryLo0 = (6 << 26) | (cfg_base >> 6) | (2 << 3) | 7;
+ entryLo1 = (6 << 26) | (cfg_base >> 6) | (0x1000 >> 6) | (2 << 3) | 7;
+ if ((entryLo0 != ctx->last_elo0) || (entryLo1 != ctx->last_elo1)) {
+ mod_wired_entry(ctx->wired_entry, entryLo0, entryLo1,
+ (unsigned long)ctx->pci_cfg_vm->addr, PM_4K);
+ ctx->last_elo0 = entryLo0;
+ ctx->last_elo1 = entryLo1;
+ }
+
+ if (access_type == PCI_ACCESS_WRITE)
+ __raw_writel(*data, ctx->pci_cfg_vm->addr + offset);
+ else
+ *data = __raw_readl(ctx->pci_cfg_vm->addr + offset);
+ wmb();
+
+ DBG("alchemy-pci: cfg access %d bus %u dev %u at %x dat %x conf %lx\n",
+ access_type, bus->number, device, where, *data, offset);
+
+ /* check for errors, master abort */
+ status = __raw_readl(ctx->regs + PCI_REG_STATCMD);
+ if (status & (1 << 29)) {
+ *data = 0xffffffff;
+ error = -1;
+ DBG("alchemy-pci: master abort on cfg access %d bus %d dev %d",
+ access_type, bus->number, device);
+ } else if ((status >> 28) & 0xf) {
+ DBG("alchemy-pci: PCI ERR detected: dev %d, status %lx\n",
+ device, (status >> 28) & 0xf);
+
+ /* clear errors */
+ __raw_writel(status & 0xf000ffff, ctx->regs + PCI_REG_STATCMD);
+
+ *data = 0xffffffff;
+ error = -1;
+ }
+
+ /* Take away the IDSEL. */
+ (void)ctx->board_pci_idsel(device, 0);
+
+ local_irq_restore(flags);
+ return error;
+}
+
+static int read_config_byte(struct pci_bus *bus, unsigned int devfn,
+ int where, u8 *val)
+{
+ u32 data;
+ int ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
+
+ if (where & 1)
+ data >>= 8;
+ if (where & 2)
+ data >>= 16;
+ *val = data & 0xff;
+ return ret;
+}
+
+static int read_config_word(struct pci_bus *bus, unsigned int devfn,
+ int where, u16 *val)
+{
+ u32 data;
+ int ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
+
+ if (where & 2)
+ data >>= 16;
+ *val = data & 0xffff;
+ return ret;
+}
+
+static int read_config_dword(struct pci_bus *bus, unsigned int devfn,
+ int where, u32 *val)
+{
+ return config_access(PCI_ACCESS_READ, bus, devfn, where, val);
+}
+
+static int write_config_byte(struct pci_bus *bus, unsigned int devfn,
+ int where, u8 val)
+{
+ u32 data = 0;
+
+ if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
+ return -1;
+
+ data = (data & ~(0xff << ((where & 3) << 3))) |
+ (val << ((where & 3) << 3));
+
+ if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
+ return -1;
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static int write_config_word(struct pci_bus *bus, unsigned int devfn,
+ int where, u16 val)
+{
+ u32 data = 0;
+
+ if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
+ return -1;
+
+ data = (data & ~(0xffff << ((where & 3) << 3))) |
+ (val << ((where & 3) << 3));
+
+ if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
+ return -1;
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static int write_config_dword(struct pci_bus *bus, unsigned int devfn,
+ int where, u32 val)
+{
+ return config_access(PCI_ACCESS_WRITE, bus, devfn, where, &val);
+}
+
+static int alchemy_pci_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ switch (size) {
+ case 1: {
+ u8 _val;
+ int rc = read_config_byte(bus, devfn, where, &_val);
+
+ *val = _val;
+ return rc;
+ }
+ case 2: {
+ u16 _val;
+ int rc = read_config_word(bus, devfn, where, &_val);
+
+ *val = _val;
+ return rc;
+ }
+ default:
+ return read_config_dword(bus, devfn, where, val);
+ }
+}
+
+static int alchemy_pci_write(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ switch (size) {
+ case 1:
+ return write_config_byte(bus, devfn, where, (u8) val);
+ case 2:
+ return write_config_word(bus, devfn, where, (u16) val);
+ default:
+ return write_config_dword(bus, devfn, where, val);
+ }
+}
+
+static struct pci_ops alchemy_pci_ops = {
+ .read = alchemy_pci_read,
+ .write = alchemy_pci_write,
+};
+
+static int alchemy_pci_def_idsel(unsigned int devsel, int assert)
+{
+ return 1; /* success */
+}
+
+static int __devinit alchemy_pci_probe(struct platform_device *pdev)
+{
+ struct alchemy_pci_platdata *pd = pdev->dev.platform_data;
+ struct alchemy_pci_context *ctx;
+ void __iomem *virt_io;
+ unsigned long val;
+ struct resource *r;
+ int ret;
+
+ /* need at least PCI IRQ mapping table */
+ if (!pd) {
+ dev_err(&pdev->dev, "need platform data for PCI setup\n");
+ ret = -ENODEV;
+ goto out;
+ }
+
+ ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+ if (!ctx) {
+ dev_err(&pdev->dev, "no memory for pcictl context\n");
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!r) {
+ dev_err(&pdev->dev, "no pcictl ctrl regs resource\n");
+ ret = -ENODEV;
+ goto out1;
+ }
+
+ if (!request_mem_region(r->start, resource_size(r), pdev->name)) {
+ dev_err(&pdev->dev, "cannot claim pci regs\n");
+ ret = -ENODEV;
+ goto out1;
+ }
+
+ ctx->regs = ioremap_nocache(r->start, resource_size(r));
+ if (!ctx->regs) {
+ dev_err(&pdev->dev, "cannot map pci regs\n");
+ ret = -ENODEV;
+ goto out2;
+ }
+
+ /* map parts of the PCI IO area */
+ /* REVISIT: if this changes with a newer variant (doubt it) make this
+ * a platform resource.
+ */
+ virt_io = ioremap(AU1500_PCI_IO_PHYS_ADDR, 0x00100000);
+ if (!virt_io) {
+ dev_err(&pdev->dev, "cannot remap pci io space\n");
+ ret = -ENODEV;
+ goto out3;
+ }
+ ctx->alchemy_pci_ctrl.io_map_base = (unsigned long)virt_io;
+
+#ifdef CONFIG_DMA_NONCOHERENT
+ /* Au1500 revisions older than AD have borked coherent PCI */
+ if ((alchemy_get_cputype() == ALCHEMY_CPU_AU1500) &&
+ (read_c0_prid() < 0x01030202)) {
+ val = __raw_readl(ctx->regs + PCI_REG_CONFIG);
+ val |= PCI_CONFIG_NC;
+ __raw_writel(val, ctx->regs + PCI_REG_CONFIG);
+ wmb();
+ dev_info(&pdev->dev, "non-coherent PCI on Au1500 AA/AB/AC\n");
+ }
+#endif
+
+ if (pd->board_map_irq)
+ ctx->board_map_irq = pd->board_map_irq;
+
+ if (pd->board_pci_idsel)
+ ctx->board_pci_idsel = pd->board_pci_idsel;
+ else
+ ctx->board_pci_idsel = alchemy_pci_def_idsel;
+
+ /* fill in relevant pci_controller members */
+ ctx->alchemy_pci_ctrl.pci_ops = &alchemy_pci_ops;
+ ctx->alchemy_pci_ctrl.mem_resource = &alchemy_pci_def_memres;
+ ctx->alchemy_pci_ctrl.io_resource = &alchemy_pci_def_iores;
+
+ /* we can't ioremap the entire pci config space because it's too large,
+ * nor can we dynamically ioremap it because some drivers use the
+ * PCI config routines from within atomic contex and that becomes a
+ * problem in get_vm_area(). Instead we use one wired TLB entry to
+ * handle all config accesses for all busses.
+ */
+ ctx->pci_cfg_vm = get_vm_area(0x2000, VM_IOREMAP);
+ if (!ctx->pci_cfg_vm) {
+ dev_err(&pdev->dev, "unable to get vm area\n");
+ ret = -ENOMEM;
+ goto out4;
+ }
+ ctx->wired_entry = 8192; /* impossibly high value */
+
+ set_io_port_base((unsigned long)ctx->alchemy_pci_ctrl.io_map_base);
+
+ /* board may want to modify bits in the config register, do it now */
+ val = __raw_readl(ctx->regs + PCI_REG_CONFIG);
+ val &= ~pd->pci_cfg_clr;
+ val |= pd->pci_cfg_set;
+ val &= ~PCI_CONFIG_PD; /* clear disable bit */
+ __raw_writel(val, ctx->regs + PCI_REG_CONFIG);
+ wmb();
+
+ platform_set_drvdata(pdev, ctx);
+ register_pci_controller(&ctx->alchemy_pci_ctrl);
+
+ return 0;
+
+out4:
+ iounmap(virt_io);
+out3:
+ iounmap(ctx->regs);
+out2:
+ release_mem_region(r->start, resource_size(r));
+out1:
+ kfree(ctx);
+out:
+ return ret;
+}
+
+
+#ifdef CONFIG_PM
+/* save PCI controller register contents. */
+static int alchemy_pci_suspend(struct device *dev)
+{
+ struct alchemy_pci_context *ctx = dev_get_drvdata(dev);
+
+ ctx->pm[0] = __raw_readl(ctx->regs + PCI_REG_CMEM);
+ ctx->pm[1] = __raw_readl(ctx->regs + PCI_REG_CONFIG) & 0x0009ffff;
+ ctx->pm[2] = __raw_readl(ctx->regs + PCI_REG_B2BMASK_CCH);
+ ctx->pm[3] = __raw_readl(ctx->regs + PCI_REG_B2BBASE0_VID);
+ ctx->pm[4] = __raw_readl(ctx->regs + PCI_REG_B2BBASE1_SID);
+ ctx->pm[5] = __raw_readl(ctx->regs + PCI_REG_MWMASK_DEV);
+ ctx->pm[6] = __raw_readl(ctx->regs + PCI_REG_MWBASE_REV_CCL);
+ ctx->pm[7] = __raw_readl(ctx->regs + PCI_REG_ID);
+ ctx->pm[8] = __raw_readl(ctx->regs + PCI_REG_CLASSREV);
+ ctx->pm[9] = __raw_readl(ctx->regs + PCI_REG_PARAM);
+ ctx->pm[10] = __raw_readl(ctx->regs + PCI_REG_MBAR);
+ ctx->pm[11] = __raw_readl(ctx->regs + PCI_REG_TIMEOUT);
+
+ return 0;
+}
+
+static int alchemy_pci_resume(struct device *dev)
+{
+ struct alchemy_pci_context *ctx = dev_get_drvdata(dev);
+
+ __raw_writel(ctx->pm[0], ctx->regs + PCI_REG_CMEM);
+ __raw_writel(ctx->pm[2], ctx->regs + PCI_REG_B2BMASK_CCH);
+ __raw_writel(ctx->pm[3], ctx->regs + PCI_REG_B2BBASE0_VID);
+ __raw_writel(ctx->pm[4], ctx->regs + PCI_REG_B2BBASE1_SID);
+ __raw_writel(ctx->pm[5], ctx->regs + PCI_REG_MWMASK_DEV);
+ __raw_writel(ctx->pm[6], ctx->regs + PCI_REG_MWBASE_REV_CCL);
+ __raw_writel(ctx->pm[7], ctx->regs + PCI_REG_ID);
+ __raw_writel(ctx->pm[8], ctx->regs + PCI_REG_CLASSREV);
+ __raw_writel(ctx->pm[9], ctx->regs + PCI_REG_PARAM);
+ __raw_writel(ctx->pm[10], ctx->regs + PCI_REG_MBAR);
+ __raw_writel(ctx->pm[11], ctx->regs + PCI_REG_TIMEOUT);
+ wmb();
+ __raw_writel(ctx->pm[1], ctx->regs + PCI_REG_CONFIG);
+ wmb();
+
+ return 0;
+}
+
+static const struct dev_pm_ops alchemy_pci_pmops = {
+ .suspend = alchemy_pci_suspend,
+ .resume = alchemy_pci_resume,
+};
+
+#define ALCHEMY_PCICTL_PM (&alchemy_pci_pmops)
+
+#else
+#define ALCHEMY_PCICTL_PM NULL
+#endif
+
+static struct platform_driver alchemy_pcictl_driver = {
+ .probe = alchemy_pci_probe,
+ .driver = {
+ .name = "alchemy-pci",
+ .owner = THIS_MODULE,
+ .pm = ALCHEMY_PCICTL_PM,
+ },
+};
+
+static int __init alchemy_pci_init(void)
+{
+ /* Au1500/Au1550 have PCI */
+ switch (alchemy_get_cputype()) {
+ case ALCHEMY_CPU_AU1500:
+ case ALCHEMY_CPU_AU1550:
+ return platform_driver_register(&alchemy_pcictl_driver);
+ }
+ return 0;
+}
+arch_initcall(alchemy_pci_init);
+
+
+int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+ struct alchemy_pci_context *ctx = dev->sysdata;
+ if (ctx && ctx->board_map_irq)
+ return ctx->board_map_irq(dev, slot, pin);
+ return -1;
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+ return 0;
+}
--
1.7.6
