Detect CPU type at runtime and setup uarts accordingly; also
clean up the uart base address mess in the process as far
as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@xxxxxxxxxxxxxx>
---
arch/mips/alchemy/common/platform.c | 93 +++++++++++++++-------------
arch/mips/alchemy/devboards/prom.c | 2 +-
arch/mips/alchemy/gpr/board_setup.c | 14 +---
arch/mips/alchemy/gpr/init.c | 2 +-
arch/mips/alchemy/mtx-1/init.c | 2 +-
arch/mips/alchemy/xxs1500/board_setup.c | 11 +--
arch/mips/alchemy/xxs1500/init.c | 2 +-
arch/mips/boot/compressed/uart-alchemy.c | 2 +-
arch/mips/include/asm/mach-au1x00/au1000.h | 57 +++++++++++++----
9 files changed, 107 insertions(+), 78 deletions(-)
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 9e7814d..36489fb 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -30,21 +30,12 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
#ifdef CONFIG_SERIAL_8250
switch (state) {
case 0:
- if ((__raw_readl(port->membase + UART_MOD_CNTRL) & 3) != 3) {
- /* power-on sequence as suggested in the databooks */
- __raw_writel(0, port->membase + UART_MOD_CNTRL);
- wmb();
- __raw_writel(1, port->membase + UART_MOD_CNTRL);
- wmb();
- }
- __raw_writel(3, port->membase + UART_MOD_CNTRL); /* full on */
- wmb();
+ alchemy_uart_enable(CPHYSADDR(port->membase));
serial8250_do_pm(port, state, old_state);
break;
case 3: /* power off */
serial8250_do_pm(port, state, old_state);
- __raw_writel(0, port->membase + UART_MOD_CNTRL);
- wmb();
+ alchemy_uart_disable(CPHYSADDR(port->membase));
break;
default:
serial8250_do_pm(port, state, old_state);
@@ -65,38 +56,60 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
.pm = alchemy_8250_pm, \
}
-static struct plat_serial8250_port au1x00_uart_data[] = {
-#if defined(CONFIG_SOC_AU1000)
- PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
- PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
- PORT(UART2_PHYS_ADDR, AU1000_UART2_INT),
- PORT(UART3_PHYS_ADDR, AU1000_UART3_INT),
-#elif defined(CONFIG_SOC_AU1500)
- PORT(UART0_PHYS_ADDR, AU1500_UART0_INT),
- PORT(UART3_PHYS_ADDR, AU1500_UART3_INT),
-#elif defined(CONFIG_SOC_AU1100)
- PORT(UART0_PHYS_ADDR, AU1100_UART0_INT),
- PORT(UART1_PHYS_ADDR, AU1100_UART1_INT),
- PORT(UART3_PHYS_ADDR, AU1100_UART3_INT),
-#elif defined(CONFIG_SOC_AU1550)
- PORT(UART0_PHYS_ADDR, AU1550_UART0_INT),
- PORT(UART1_PHYS_ADDR, AU1550_UART1_INT),
- PORT(UART3_PHYS_ADDR, AU1550_UART3_INT),
-#elif defined(CONFIG_SOC_AU1200)
- PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
- PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
-#endif
- { },
+static struct plat_serial8250_port au1x00_uart_data[][4] __initdata = {
+ [ALCHEMY_CPU_AU1000] = {
+ PORT(AU1000_UART0_PHYS_ADDR, AU1000_UART0_INT),
+ PORT(AU1000_UART1_PHYS_ADDR, AU1000_UART1_INT),
+ PORT(AU1000_UART2_PHYS_ADDR, AU1000_UART2_INT),
+ PORT(AU1000_UART3_PHYS_ADDR, AU1000_UART3_INT),
+ },
+ [ALCHEMY_CPU_AU1500] = {
+ PORT(AU1000_UART0_PHYS_ADDR, AU1500_UART0_INT),
+ PORT(AU1000_UART3_PHYS_ADDR, AU1500_UART3_INT),
+ },
+ [ALCHEMY_CPU_AU1100] = {
+ PORT(AU1000_UART0_PHYS_ADDR, AU1100_UART0_INT),
+ PORT(AU1000_UART1_PHYS_ADDR, AU1100_UART1_INT),
+ PORT(AU1000_UART3_PHYS_ADDR, AU1100_UART3_INT),
+ },
+ [ALCHEMY_CPU_AU1550] = {
+ PORT(AU1000_UART0_PHYS_ADDR, AU1550_UART0_INT),
+ PORT(AU1000_UART1_PHYS_ADDR, AU1550_UART1_INT),
+ PORT(AU1000_UART3_PHYS_ADDR, AU1550_UART3_INT),
+ },
+ [ALCHEMY_CPU_AU1200] = {
+ PORT(AU1000_UART0_PHYS_ADDR, AU1200_UART0_INT),
+ PORT(AU1000_UART1_PHYS_ADDR, AU1200_UART1_INT),
+ },
};
static struct platform_device au1xx0_uart_device = {
.name = "serial8250",
.id = PLAT8250_DEV_AU1X00,
- .dev = {
- .platform_data = au1x00_uart_data,
- },
};
+static void __init alchemy_setup_uarts(int ctype)
+{
+ unsigned int uartclk = get_au1x00_uart_baud_base() * 16;
+ int s = sizeof(struct plat_serial8250_port);
+ int c = alchemy_get_uarts(ctype);
+ struct plat_serial8250_port *ports;
+
+ ports = kzalloc(s * (c + 1), GFP_KERNEL);
+ if (!ports) {
+ printk(KERN_INFO "Alchemy: no memory for UART data\n");
+ return;
+ }
+ memcpy(ports, au1x00_uart_data[ctype], s * c);
+ au1xx0_uart_device.dev.platform_data = ports;
+
+ /* Fill up uartclk. */
+ for (s = 0; s < c; s++)
+ ports[s].uartclk = uartclk;
+ if (platform_device_register(&au1xx0_uart_device))
+ printk(KERN_INFO "Alchemy: failed to register UARTs\n");
+}
+
/* OHCI (USB full speed host controller) */
static struct resource au1xxx_usb_ohci_resources[] = {
[0] = {
@@ -442,7 +455,6 @@ void __init au1xxx_override_eth_cfg(unsigned int port,
}
static struct platform_device *au1xxx_platform_devices[] __initdata = {
- &au1xx0_uart_device,
&au1xxx_usb_ohci_device,
#ifdef CONFIG_FB_AU1100
&au1100_lcd_device,
@@ -465,13 +477,10 @@ static struct platform_device *au1xxx_platform_devices[] __initdata = {
static int __init au1xxx_platform_init(void)
{
- unsigned int uartclk = get_au1x00_uart_baud_base() * 16;
- int err, i;
+ int err, i, ctype = alchemy_get_cputype();
unsigned char ethaddr[6];
- /* Fill up uartclk. */
- for (i = 0; au1x00_uart_data[i].flags; i++)
- au1x00_uart_data[i].uartclk = uartclk;
+ alchemy_setup_uarts(ctype);
/* use firmware-provided mac addr if available and necessary */
i = prom_get_ethernet_addr(ethaddr);
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index baeb213..e5306b5 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -62,5 +62,5 @@ void __init prom_init(void)
void prom_putchar(unsigned char c)
{
- alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
}
diff --git a/arch/mips/alchemy/gpr/board_setup.c b/arch/mips/alchemy/gpr/board_setup.c
index ad2e3f1..5f8f069 100644
--- a/arch/mips/alchemy/gpr/board_setup.c
+++ b/arch/mips/alchemy/gpr/board_setup.c
@@ -36,9 +36,6 @@
#include <prom.h>
-#define UART1_ADDR KSEG1ADDR(UART1_PHYS_ADDR)
-#define UART3_ADDR KSEG1ADDR(UART3_PHYS_ADDR)
-
char irq_tab_alchemy[][5] __initdata = {
[0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff },
};
@@ -67,18 +64,15 @@ static void gpr_power_off(void)
void __init board_setup(void)
{
- printk(KERN_INFO "Tarpeze ITS GPR board\n");
+ printk(KERN_INFO "Trapeze ITS GPR board\n");
pm_power_off = gpr_power_off;
_machine_halt = gpr_power_off;
_machine_restart = gpr_reset;
- /* Enable UART3 */
- au_writel(0x1, UART3_ADDR + UART_MOD_CNTRL);/* clock enable (CE) */
- au_writel(0x3, UART3_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
- /* Enable UART1 */
- au_writel(0x1, UART1_ADDR + UART_MOD_CNTRL); /* clock enable (CE) */
- au_writel(0x3, UART1_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
+ /* Enable UART1/3 */
+ alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+ alchemy_uart_enable(AU1000_UART1_PHYS_ADDR);
/* Take away Reset of UMTS-card */
alchemy_gpio_direction_output(215, 1);
diff --git a/arch/mips/alchemy/gpr/init.c b/arch/mips/alchemy/gpr/init.c
index f044f4c..229aafa 100644
--- a/arch/mips/alchemy/gpr/init.c
+++ b/arch/mips/alchemy/gpr/init.c
@@ -59,5 +59,5 @@ void __init prom_init(void)
void prom_putchar(unsigned char c)
{
- alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
}
diff --git a/arch/mips/alchemy/mtx-1/init.c b/arch/mips/alchemy/mtx-1/init.c
index f8d2557..2e81cc7 100644
--- a/arch/mips/alchemy/mtx-1/init.c
+++ b/arch/mips/alchemy/mtx-1/init.c
@@ -62,5 +62,5 @@ void __init prom_init(void)
void prom_putchar(unsigned char c)
{
- alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
}
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index febfb0f..81e57fa 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -66,13 +66,10 @@ void __init board_setup(void)
au_writel(pin_func, SYS_PINFUNC);
/* Enable UART */
- au_writel(0x01, UART3_ADDR + UART_MOD_CNTRL); /* clock enable (CE) */
- mdelay(10);
- au_writel(0x03, UART3_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
- mdelay(10);
-
- /* Enable DTR = USB power up */
- au_writel(0x01, UART3_ADDR + UART_MCR); /* UART_MCR_DTR is 0x01??? */
+ alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+ /* Enable DTR (MCR bit 0) = USB power up */
+ __raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
+ wmb();
#ifdef CONFIG_PCI
#if defined(__MIPSEB__)
diff --git a/arch/mips/alchemy/xxs1500/init.c b/arch/mips/alchemy/xxs1500/init.c
index 15125c2..0bf768f 100644
--- a/arch/mips/alchemy/xxs1500/init.c
+++ b/arch/mips/alchemy/xxs1500/init.c
@@ -60,5 +60,5 @@ void __init prom_init(void)
void prom_putchar(unsigned char c)
{
- alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
}
diff --git a/arch/mips/boot/compressed/uart-alchemy.c b/arch/mips/boot/compressed/uart-alchemy.c
index 1bff22f..eb063e6 100644
--- a/arch/mips/boot/compressed/uart-alchemy.c
+++ b/arch/mips/boot/compressed/uart-alchemy.c
@@ -3,5 +3,5 @@
void putc(char c)
{
/* all current (Jan. 2010) in-kernel boards */
- alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+ alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
}
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index eb8f103..c4ffb20 100644
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -161,6 +161,45 @@ static inline int alchemy_get_cputype(void)
return ALCHEMY_CPU_UNKNOWN;
}
+/* return number of uarts on a given cputype */
+static inline int alchemy_get_uarts(int type)
+{
+ switch (type) {
+ case ALCHEMY_CPU_AU1000:
+ return 4;
+ case ALCHEMY_CPU_AU1500:
+ case ALCHEMY_CPU_AU1200:
+ return 2;
+ case ALCHEMY_CPU_AU1100:
+ case ALCHEMY_CPU_AU1550:
+ return 3;
+ }
+ return 0;
+}
+
+/* enable an UART block if it isn't already */
+static inline void alchemy_uart_enable(u32 uart_phys)
+{
+ void __iomem *addr = (void __iomem *)KSEG1ADDR(uart_phys);
+
+ /* reset, enable clock, deassert reset */
+ if ((__raw_readl(addr + 0x100) & 3) != 3) {
+ __raw_writel(0, addr + 0x100);
+ wmb();
+ __raw_writel(1, addr + 0x100);
+ wmb();
+ }
+ __raw_writel(3, addr + 0x100);
+ wmb();
+}
+
+static inline void alchemy_uart_disable(u32 uart_phys)
+{
+ void __iomem *addr = (void __iomem *)KSEG1ADDR(uart_phys);
+ __raw_writel(0, addr + 0x100); /* UART_MOD_CNTRL */
+ wmb();
+}
+
static inline void alchemy_uart_putchar(u32 uart_phys, u8 c)
{
void __iomem *base = (void __iomem *)KSEG1ADDR(uart_phys);
@@ -634,6 +673,10 @@ enum soc_au1200_ints {
*/
#define AU1000_IC0_PHYS_ADDR 0x10400000 /* 01234 */
+#define AU1000_UART0_PHYS_ADDR 0x11100000 /* 01234 */
+#define AU1000_UART1_PHYS_ADDR 0x11200000 /* 0234 */
+#define AU1000_UART2_PHYS_ADDR 0x11300000 /* 0 */
+#define AU1000_UART3_PHYS_ADDR 0x11400000 /* 0123 */
#define AU1000_IC1_PHYS_ADDR 0x11800000 /* 01234 */
#define AU1550_DBDMA_PHYS_ADDR 0x14002000 /* 34 */
#define AU1550_DBDMA_CONF_PHYS_ADDR 0x14003000 /* 34 */
@@ -660,10 +703,6 @@ enum soc_au1200_ints {
#define MACDMA0_PHYS_ADDR 0x14004000
#define MACDMA1_PHYS_ADDR 0x14004200
#define I2S_PHYS_ADDR 0x11000000
-#define UART0_PHYS_ADDR 0x11100000
-#define UART1_PHYS_ADDR 0x11200000
-#define UART2_PHYS_ADDR 0x11300000
-#define UART3_PHYS_ADDR 0x11400000
#define SSI0_PHYS_ADDR 0x11600000
#define SSI1_PHYS_ADDR 0x11680000
#define SYS_PHYS_ADDR 0x11900000
@@ -695,8 +734,6 @@ enum soc_au1200_ints {
#define MACDMA0_PHYS_ADDR 0x14004000
#define MACDMA1_PHYS_ADDR 0x14004200
#define I2S_PHYS_ADDR 0x11000000
-#define UART0_PHYS_ADDR 0x11100000
-#define UART3_PHYS_ADDR 0x11400000
#define GPIO2_PHYS_ADDR 0x11700000
#define SYS_PHYS_ADDR 0x11900000
#define PCI_MEM_PHYS_ADDR 0x400000000ULL
@@ -732,9 +769,6 @@ enum soc_au1200_ints {
#define MACDMA0_PHYS_ADDR 0x14004000
#define MACDMA1_PHYS_ADDR 0x14004200
#define I2S_PHYS_ADDR 0x11000000
-#define UART0_PHYS_ADDR 0x11100000
-#define UART1_PHYS_ADDR 0x11200000
-#define UART3_PHYS_ADDR 0x11400000
#define SSI0_PHYS_ADDR 0x11600000
#define SSI1_PHYS_ADDR 0x11680000
#define GPIO2_PHYS_ADDR 0x11700000
@@ -758,9 +792,6 @@ enum soc_au1200_ints {
#define MACEN_PHYS_ADDR 0x10520000
#define MACDMA0_PHYS_ADDR 0x14004000
#define MACDMA1_PHYS_ADDR 0x14004200
-#define UART0_PHYS_ADDR 0x11100000
-#define UART1_PHYS_ADDR 0x11200000
-#define UART3_PHYS_ADDR 0x11400000
#define GPIO2_PHYS_ADDR 0x11700000
#define SYS_PHYS_ADDR 0x11900000
#define PE_PHYS_ADDR 0x14008000
@@ -786,8 +817,6 @@ enum soc_au1200_ints {
#define CIM_PHYS_ADDR 0x14004000
#define USBM_PHYS_ADDR 0x14020000
#define USBH_PHYS_ADDR 0x14020100
-#define UART0_PHYS_ADDR 0x11100000
-#define UART1_PHYS_ADDR 0x11200000
#define GPIO2_PHYS_ADDR 0x11700000
#define SYS_PHYS_ADDR 0x11900000
#define PSC0_PHYS_ADDR 0x11A00000
--
1.7.5.rc3
