From: Wu Zhangjin <wuzhangjin@xxxxxxxxx>
fuloong2f, yeeloong2f and menglong2f have different reset/shutdown
logic, this patch add respective support for them.
Signed-off-by: Wu Zhangjin <wuzhangjin@xxxxxxxxx>
---
arch/mips/include/asm/mach-loongson/loongson.h | 7 +
arch/mips/loongson/lemote-2f/Makefile | 2 +-
arch/mips/loongson/lemote-2f/reset.c | 172 ++++++++++++++++++++++++
3 files changed, 180 insertions(+), 1 deletions(-)
create mode 100644 arch/mips/loongson/lemote-2f/reset.c
diff --git a/arch/mips/include/asm/mach-loongson/loongson.h b/arch/mips/include/asm/mach-loongson/loongson.h
index e7e7a08..5b83bea 100644
--- a/arch/mips/include/asm/mach-loongson/loongson.h
+++ b/arch/mips/include/asm/mach-loongson/loongson.h
@@ -42,6 +42,13 @@ extern void __init set_irq_trigger_mode(void);
extern void __init mach_init_irq(void);
extern void mach_irq_dispatch(unsigned int pending);
+/* We need this in some places... */
+#define delay() ({ \
+ int x; \
+ for (x = 0; x < 100000; x++) \
+ __asm__ __volatile__(""); \
+})
+
#define LOONGSON_REG(x) \
(*(volatile u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))
diff --git a/arch/mips/loongson/lemote-2f/Makefile b/arch/mips/loongson/lemote-2f/Makefile
index 2e18897..da543b1 100644
--- a/arch/mips/loongson/lemote-2f/Makefile
+++ b/arch/mips/loongson/lemote-2f/Makefile
@@ -2,4 +2,4 @@
# Makefile for lemote loongson2f family machines
#
-obj-y += irq.o
+obj-y += irq.o reset.o
diff --git a/arch/mips/loongson/lemote-2f/reset.c b/arch/mips/loongson/lemote-2f/reset.c
new file mode 100644
index 0000000..0458a1c
--- /dev/null
+++ b/arch/mips/loongson/lemote-2f/reset.c
@@ -0,0 +1,172 @@
+/* Board-specific reboot/shutdown routines
+ *
+ * Copyright (c) 2009 Philippe Vachon <philippe@xxxxxxxxx>
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzj@xxxxxxxxxx
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/types.h>
+
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+#include <cs5536/cs5536.h>
+
+static void reset_cpu(void)
+{
+ /*
+ * reset cpu to full speed, this is needed when enabling cpu frequency
+ * scalling
+ */
+ LOONGSON_CHIPCFG0 |= 0x7;
+}
+
+/* reset support for fuloong2f */
+
+static void fl2f_reboot(void)
+{
+ reset_cpu();
+
+ /* send a reset signal to south bridge.
+ *
+ * NOTE: if enable "Power Management" in kernel, rtl8169 will not reset
+ * normally with this reset operation and it will not work in PMON, but
+ * you can type halt command and then reboot, seems the hardware reset
+ * logic not work normally.
+ */
+ {
+ u32 hi, lo;
+ _rdmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), &hi, &lo);
+ lo |= 0x00000001;
+ _wrmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), hi, lo);
+ }
+}
+
+static void fl2f_shutdown(void)
+{
+ u32 hi, lo, val;
+ int gpio_base;
+
+ /* get gpio base */
+ _rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo);
+ gpio_base = lo & 0xff00;
+
+ /* make cs5536 gpio13 output enable */
+ val = inl(gpio_base + GPIOL_OUT_EN);
+ val &= ~(1 << (16 + 13));
+ val |= (1 << 13);
+ outl(val, gpio_base + GPIOL_OUT_EN);
+ mmiowb();
+ /* make cs5536 gpio13 output low level voltage. */
+ val = inl(gpio_base + GPIOL_OUT_VAL) & ~(1 << (13));
+ val |= (1 << (16 + 13));
+ outl(val, gpio_base + GPIOL_OUT_VAL);
+ mmiowb();
+}
+
+/* reset support for yeeloong2f and mengloong2f notebook */
+
+/*
+ * The following registers are determined by the EC index configuration.
+ * 1. fill the PORT_HIGH as EC register high part.
+ * 2. fill the PORT_LOW as EC register low part.
+ * 3. fill the PORT_DATA as EC register write data or get the data from it.
+ */
+
+#define EC_IO_PORT_HIGH 0x0381
+#define EC_IO_PORT_LOW 0x0382
+#define EC_IO_PORT_DATA 0x0383
+#define REG_RESET_HIGH 0xF4 /* reset the machine auto-clear : rd/wr */
+#define REG_RESET_LOW 0xEC
+#define BIT_RESET_ON (1 << 0)
+
+void ml2f_reboot(void)
+{
+ reset_cpu();
+
+ /* sending an reset signal to EC(embedded controller) */
+ outb(REG_RESET_HIGH, EC_IO_PORT_HIGH);
+ outb(REG_RESET_LOW, EC_IO_PORT_LOW);
+ mmiowb();
+ outb(BIT_RESET_ON, EC_IO_PORT_DATA);
+ mmiowb();
+}
+
+#define yl2f89_reboot ml2f_reboot
+
+/* menglong(7inches) laptop has different shutdown logic from 8.9inches */
+#define EC_SHUTDOWN_IO_PORT_HIGH 0xff2d
+#define EC_SHUTDOWN_IO_PORT_LOW 0xff2e
+#define EC_SHUTDOWN_IO_PORT_DATA 0xff2f
+#define REG_SHUTDOWN_HIGH 0xFC
+#define REG_SHUTDOWN_LOW 0x29
+#define BIT_SHUTDOWN_ON (1 << 1)
+
+static void ml2f_shutdown(void)
+{
+ u8 val;
+ u64 i;
+
+ outb(REG_SHUTDOWN_HIGH, EC_SHUTDOWN_IO_PORT_HIGH);
+ outb(REG_SHUTDOWN_LOW, EC_SHUTDOWN_IO_PORT_LOW);
+ mmiowb();
+ val = inb(EC_SHUTDOWN_IO_PORT_DATA);
+ outb(val & (~BIT_SHUTDOWN_ON), EC_SHUTDOWN_IO_PORT_DATA);
+ mmiowb();
+ /* need enough wait here... how many microseconds needs? */
+ for (i = 0; i < 0x10000; i++)
+ delay();
+ outb(val | BIT_SHUTDOWN_ON, EC_SHUTDOWN_IO_PORT_DATA);
+ mmiowb();
+}
+
+static void yl2f89_shutdown(void)
+{
+ /* cpu-gpio0 output low */
+ LOONGSON_GPIODATA &= ~0x00000001;
+ /* cpu-gpio0 as output */
+ LOONGSON_GPIOIE &= ~0x00000001;
+}
+
+void mach_prepare_reboot(void)
+{
+ switch (mips_machtype) {
+ case MACH_LEMOTE_FL2F:
+ fl2f_reboot();
+ break;
+ case MACH_LEMOTE_ML2F7:
+ ml2f_reboot();
+ break;
+ case MACH_LEMOTE_YL2F89:
+ yl2f89_reboot();
+ break;
+ default:
+ break;
+ }
+}
+
+void mach_prepare_shutdown(void)
+{
+ switch (mips_machtype) {
+ case MACH_LEMOTE_FL2F:
+ fl2f_shutdown();
+ break;
+ case MACH_LEMOTE_ML2F7:
+ ml2f_shutdown();
+ break;
+ case MACH_LEMOTE_YL2F89:
+ yl2f89_shutdown();
+ break;
+ default:
+ break;
+ }
+}
--
1.6.2.1
