We're strongly discouraged from using the IC_CLR_INTR register because
it clears all software-clearable interrupts asserted at the moment.
stat = read(IC_INTR_STAT);
:
: <=== Interrupts asserted during this period will be lost
:
read(IC_CLR_INTR);
Use the separately-prepared IC_CLR_* registers, instead.
At the same time, this patch adds all remaining interrupt definitions
available in the DesignWare I2C hardware.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@xxxxxxxxx>
---
drivers/i2c/busses/i2c-designware.c | 77 +++++++++++++++++++++++++++++++++--
1 files changed, 73 insertions(+), 4 deletions(-)
diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c
index a4f928e..efddae1 100644
--- a/drivers/i2c/busses/i2c-designware.c
+++ b/drivers/i2c/busses/i2c-designware.c
@@ -49,7 +49,18 @@
#define DW_IC_FS_SCL_LCNT 0x20
#define DW_IC_INTR_STAT 0x2c
#define DW_IC_INTR_MASK 0x30
+#define DW_IC_RAW_INTR_STAT 0x34
#define DW_IC_CLR_INTR 0x40
+#define DW_IC_CLR_RX_UNDER 0x44
+#define DW_IC_CLR_RX_OVER 0x48
+#define DW_IC_CLR_TX_OVER 0x4c
+#define DW_IC_CLR_RD_REQ 0x50
+#define DW_IC_CLR_TX_ABRT 0x54
+#define DW_IC_CLR_RX_DONE 0x58
+#define DW_IC_CLR_ACTIVITY 0x5c
+#define DW_IC_CLR_STOP_DET 0x60
+#define DW_IC_CLR_START_DET 0x64
+#define DW_IC_CLR_GEN_CALL 0x68
#define DW_IC_ENABLE 0x6c
#define DW_IC_STATUS 0x70
#define DW_IC_TXFLR 0x74
@@ -64,9 +75,18 @@
#define DW_IC_CON_RESTART_EN 0x20
#define DW_IC_CON_SLAVE_DISABLE 0x40
-#define DW_IC_INTR_TX_EMPTY 0x10
-#define DW_IC_INTR_TX_ABRT 0x40
+#define DW_IC_INTR_RX_UNDER 0x001
+#define DW_IC_INTR_RX_OVER 0x002
+#define DW_IC_INTR_RX_FULL 0x004
+#define DW_IC_INTR_TX_OVER 0x008
+#define DW_IC_INTR_TX_EMPTY 0x010
+#define DW_IC_INTR_RD_REQ 0x020
+#define DW_IC_INTR_TX_ABRT 0x040
+#define DW_IC_INTR_RX_DONE 0x080
+#define DW_IC_INTR_ACTIVITY 0x100
#define DW_IC_INTR_STOP_DET 0x200
+#define DW_IC_INTR_START_DET 0x400
+#define DW_IC_INTR_GEN_CALL 0x800
#define DW_IC_STATUS_ACTIVITY 0x1
@@ -439,6 +459,55 @@ static void dw_i2c_pump_msg(unsigned long data)
writel(intr_mask, dev->base + DW_IC_INTR_MASK);
}
+static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev)
+{
+ u32 stat;
+
+ /*
+ * The IC_INTR_STAT register just indicates "enabled" interrupts.
+ * Ths unmasked raw version of interrupt status bits are available
+ * in the IC_RAW_INTR_STAT register.
+ *
+ * That is,
+ * stat = readl(IC_INTR_STAT);
+ * equals to,
+ * stat = readl(IC_RAW_INTR_STAT) & readl(IC_INTR_MASK);
+ *
+ * The raw version might be useful for debugging purposes.
+ */
+ stat = readl(dev->base + DW_IC_INTR_STAT);
+
+ /*
+ * Do not use the IC_CLR_INTR register to clear interrupts, or
+ * you'll miss some interrupts, triggered during the period from
+ * reading IC_INTR_STAT to reading IC_CLR_INTR.
+ *
+ * Use the separately-prepared IC_CLR_* registers instead.
+ */
+ if (stat & DW_IC_INTR_RX_UNDER)
+ readl(dev->base + DW_IC_CLR_RX_UNDER);
+ if (stat & DW_IC_INTR_RX_OVER)
+ readl(dev->base + DW_IC_CLR_RX_OVER);
+ if (stat & DW_IC_INTR_TX_OVER)
+ readl(dev->base + DW_IC_CLR_TX_OVER);
+ if (stat & DW_IC_INTR_RD_REQ)
+ readl(dev->base + DW_IC_CLR_RD_REQ);
+ if (stat & DW_IC_INTR_TX_ABRT)
+ readl(dev->base + DW_IC_CLR_TX_ABRT);
+ if (stat & DW_IC_INTR_RX_DONE)
+ readl(dev->base + DW_IC_CLR_RX_DONE);
+ if (stat & DW_IC_INTR_ACTIVITY)
+ readl(dev->base + DW_IC_CLR_ACTIVITY);
+ if (stat & DW_IC_INTR_STOP_DET)
+ readl(dev->base + DW_IC_CLR_STOP_DET);
+ if (stat & DW_IC_INTR_START_DET)
+ readl(dev->base + DW_IC_CLR_START_DET);
+ if (stat & DW_IC_INTR_GEN_CALL)
+ readl(dev->base + DW_IC_CLR_GEN_CALL);
+
+ return stat;
+}
+
/*
* Interrupt service routine. This gets called whenever an I2C interrupt
* occurs.
@@ -448,8 +517,9 @@ static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id)
struct dw_i2c_dev *dev = dev_id;
u32 stat;
- stat = readl(dev->base + DW_IC_INTR_STAT);
+ stat = i2c_dw_read_clear_intrbits(dev);
dev_dbg(dev->dev, "%s: stat=0x%x\n", __func__, stat);
+
if (stat & DW_IC_INTR_TX_ABRT) {
dev->abort_source = readl(dev->base + DW_IC_TX_ABRT_SOURCE);
dev->cmd_err |= DW_IC_ERR_TX_ABRT;
@@ -457,7 +527,6 @@ static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id)
} else if (stat & DW_IC_INTR_TX_EMPTY)
tasklet_schedule(&dev->pump_msg);
- readl(dev->base + DW_IC_CLR_INTR); /* clear interrupts */
writel(0, dev->base + DW_IC_INTR_MASK); /* disable interrupts */
if (stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET))
complete(&dev->cmd_complete);
--
1.6.5
