Now that the SB1250 DUART is supported with a serial/ driver the old one
may be removed.
Signed-off-by: Maciej W. Rozycki <macro@xxxxxxxxxxxxxx>
---
Ralf,
It probably does not build anymore and has no suspected maintainer.
Unless one steps in this is my vote for the driver to be removed. It has
never made its way upstream and is unlikely to regardless. RIP.
Please apply,
Maciej
patch-mips-2.6.22-20070719-char-sb1250-duart-28
diff -up --recursive --new-file linux-mips-2.6.22-20070719.macro/drivers/char/Kconfig linux-mips-2.6.22-20070719/drivers/char/Kconfig
--- linux-mips-2.6.22-20070719.macro/drivers/char/Kconfig 2007-07-19 12:14:33.000000000 +0000
+++ linux-mips-2.6.22-20070719/drivers/char/Kconfig 2007-07-19 12:35:30.000000000 +0000
@@ -372,14 +372,6 @@ config ISTALLION
To compile this driver as a module, choose M here: the
module will be called istallion.
-config SIBYTE_SB1250_DUART
- bool "Support for BCM1xxx onchip DUART"
- depends on MIPS && SIBYTE_SB1xxx_SOC=y
-
-config SIBYTE_SB1250_DUART_CONSOLE
- bool "Console on BCM1xxx DUART"
- depends on SIBYTE_SB1250_DUART
-
config A2232
tristate "Commodore A2232 serial support (EXPERIMENTAL)"
depends on EXPERIMENTAL && ZORRO && BROKEN_ON_SMP
diff -up --recursive --new-file linux-mips-2.6.22-20070719.macro/drivers/char/Makefile linux-mips-2.6.22-20070719/drivers/char/Makefile
--- linux-mips-2.6.22-20070719.macro/drivers/char/Makefile 2007-07-19 12:14:33.000000000 +0000
+++ linux-mips-2.6.22-20070719/drivers/char/Makefile 2007-07-19 12:35:30.000000000 +0000
@@ -33,7 +33,6 @@ obj-$(CONFIG_A2232) += ser_a2232.o gene
obj-$(CONFIG_ATARI_DSP56K) += dsp56k.o
obj-$(CONFIG_MOXA_SMARTIO) += mxser.o
obj-$(CONFIG_MOXA_SMARTIO_NEW) += mxser_new.o
-obj-$(CONFIG_SIBYTE_SB1250_DUART) += sb1250_duart.o
obj-$(CONFIG_COMPUTONE) += ip2/
obj-$(CONFIG_RISCOM8) += riscom8.o
obj-$(CONFIG_ISI) += isicom.o
diff -up --recursive --new-file linux-mips-2.6.22-20070719.macro/drivers/char/sb1250_duart.c linux-mips-2.6.22-20070719/drivers/char/sb1250_duart.c
--- linux-mips-2.6.22-20070719.macro/drivers/char/sb1250_duart.c 2007-07-19 12:14:33.000000000 +0000
+++ linux-mips-2.6.22-20070719/drivers/char/sb1250_duart.c 1970-01-01 00:00:00.000000000 +0000
@@ -1,979 +0,0 @@
-/*
- * Copyright (C) 2000,2001,2002,2003,2004 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-/*
- * Driver support for the on-chip sb1250 dual-channel serial port,
- * running in asynchronous mode. Also, support for doing a serial console
- * on one of those ports
- */
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/serial.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/console.h>
-#include <linux/kdev_t.h>
-#include <linux/major.h>
-#include <linux/termios.h>
-#include <linux/spinlock.h>
-#include <linux/irq.h>
-#include <linux/errno.h>
-#include <linux/tty.h>
-#include <linux/sched.h>
-#include <linux/tty_flip.h>
-#include <linux/timer.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <asm/delay.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <asm/sibyte/swarm.h>
-#include <asm/sibyte/sb1250.h>
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
-#include <asm/sibyte/bcm1480_regs.h>
-#include <asm/sibyte/bcm1480_int.h>
-#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
-#include <asm/sibyte/sb1250_regs.h>
-#include <asm/sibyte/sb1250_int.h>
-#else
-#error invalid SiByte UART configuation
-#endif
-#include <asm/sibyte/sb1250_uart.h>
-#include <asm/war.h>
-
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
-#define UNIT_CHANREG(n,reg) A_BCM1480_DUART_CHANREG((n),(reg))
-#define UNIT_IMRREG(n) A_BCM1480_DUART_IMRREG(n)
-#define UNIT_INT(n) (K_BCM1480_INT_UART_0 + (n))
-#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
-#define UNIT_CHANREG(n,reg) A_DUART_CHANREG((n),(reg))
-#define UNIT_IMRREG(n) A_DUART_IMRREG(n)
-#define UNIT_INT(n) (K_INT_UART_0 + (n))
-#else
-#error invalid SiByte UART configuation
-#endif
-
-/* Toggle spewing of debugging output */
-#undef DEBUG
-
-#define DEFAULT_CFLAGS (CS8 | B115200)
-
-#define TX_INTEN 1
-#define DUART_INITIALIZED 2
-
-#define DUART_MAX_LINE 4
-char sb1250_duart_present[DUART_MAX_LINE];
-EXPORT_SYMBOL(sb1250_duart_present);
-
-/*
- * In bug 1956, we get glitches that can mess up uart registers. This
- * "read-mode-reg after any register access" is an accepted workaround.
- */
-#if SIBYTE_1956_WAR
-# define SB1_SER1956_WAR { \
- u32 ignore; \
- ignore = csr_in32(uart_states[line].mode_1); \
- ignore = csr_in32(uart_states[line].mode_2); \
- }
-#else
-# define SB1_SER1956_WAR
-#endif
-
-/*
- * Still not sure what the termios structures set up here are for,
- * but we have to supply pointers to them to register the tty driver
- */
-static struct tty_driver *sb1250_duart_driver; //, sb1250_duart_callout_driver;
-
-/*
- * This lock protects both the open flags for all the uart states as
- * well as the reference count for the module
- */
-static DEFINE_SPINLOCK(open_lock);
-
-typedef struct {
- unsigned char outp_buf[SERIAL_XMIT_SIZE];
- unsigned int outp_head;
- unsigned int outp_tail;
- unsigned int outp_count;
- spinlock_t outp_lock;
- unsigned int open;
- unsigned int line;
- unsigned int last_cflags;
- unsigned long flags;
- struct tty_struct *tty;
-
- /* CSR addresses */
- unsigned int *status;
- unsigned int *imr;
- unsigned int *tx_hold;
- unsigned int *rx_hold;
- unsigned int *mode_1;
- unsigned int *mode_2;
- unsigned int *clk_sel;
- unsigned int *cmd;
-} uart_state_t;
-
-static uart_state_t uart_states[DUART_MAX_LINE];
-
-/*
- * Inline functions local to this module
- */
-
-static inline u32 READ_SERCSR(volatile u32 *addr, int line)
-{
- u32 val = csr_in32(addr);
- SB1_SER1956_WAR;
- return val;
-}
-
-static inline void WRITE_SERCSR(u32 val, volatile u32 *addr, int line)
-{
- csr_out32(val, addr);
- SB1_SER1956_WAR;
-}
-
-static void init_duart_port(uart_state_t *port, int line)
-{
- if (!(port->flags & DUART_INITIALIZED)) {
- port->line = line;
- port->status = IOADDR(UNIT_CHANREG(line, R_DUART_STATUS));
- port->imr = IOADDR(UNIT_IMRREG(line));
- port->tx_hold = IOADDR(UNIT_CHANREG(line, R_DUART_TX_HOLD));
- port->rx_hold = IOADDR(UNIT_CHANREG(line, R_DUART_RX_HOLD));
- port->mode_1 = IOADDR(UNIT_CHANREG(line, R_DUART_MODE_REG_1));
- port->mode_2 = IOADDR(UNIT_CHANREG(line, R_DUART_MODE_REG_2));
- port->clk_sel = IOADDR(UNIT_CHANREG(line, R_DUART_CLK_SEL));
- port->cmd = IOADDR(UNIT_CHANREG(line, R_DUART_CMD));
- port->last_cflags = DEFAULT_CFLAGS;
- spin_lock_init(&port->outp_lock);
- port->flags |= DUART_INITIALIZED;
- }
-}
-
-/*
- * Mask out the passed interrupt lines at the duart level. This should be
- * called while holding the associated outp_lock.
- */
-static inline void duart_mask_ints(unsigned int line, unsigned int mask)
-{
- uart_state_t *port = uart_states + line;
- u64 tmp = READ_SERCSR(port->imr, line);
- WRITE_SERCSR(tmp & ~mask, port->imr, line);
-}
-
-
-/* Unmask the passed interrupt lines at the duart level */
-static inline void duart_unmask_ints(unsigned int line, unsigned int mask)
-{
- uart_state_t *port = uart_states + line;
- u64 tmp = READ_SERCSR(port->imr, line);
- WRITE_SERCSR(tmp | mask, port->imr, line);
-}
-
-static inline void transmit_char_pio(uart_state_t *us)
-{
- struct tty_struct *tty = us->tty;
- int blocked = 0;
-
- if (spin_trylock(&us->outp_lock)) {
- for (;;) {
- if (!(READ_SERCSR(us->status, us->line) & M_DUART_TX_RDY))
- break;
- if (us->outp_count <= 0 || tty->stopped || tty->hw_stopped) {
- break;
- } else {
- WRITE_SERCSR(us->outp_buf[us->outp_head],
- us->tx_hold, us->line);
- us->outp_head = (us->outp_head + 1) & (SERIAL_XMIT_SIZE-1);
- if (--us->outp_count <= 0)
- break;
- }
- udelay(10);
- }
- spin_unlock(&us->outp_lock);
- } else {
- blocked = 1;
- }
-
- if (!us->outp_count || tty->stopped ||
- tty->hw_stopped || blocked) {
- us->flags &= ~TX_INTEN;
- duart_mask_ints(us->line, M_DUART_IMR_TX);
- }
-
- if (us->open &&
- (us->outp_count < (SERIAL_XMIT_SIZE/2))) {
- /*
- * We told the discipline at one point that we had no
- * space, so it went to sleep. Wake it up when we hit
- * half empty
- */
- if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) &&
- tty->ldisc.write_wakeup)
- tty->ldisc.write_wakeup(tty);
- wake_up_interruptible(&tty->write_wait);
- }
-}
-
-/*
- * Generic interrupt handler for both channels. dev_id is a pointer
- * to the proper uart_states structure, so from that we can derive
- * which port interrupted
- */
-
-static irqreturn_t duart_int(int irq, void *dev_id)
-{
- uart_state_t *us = (uart_state_t *)dev_id;
- struct tty_struct *tty = us->tty;
- unsigned int status = READ_SERCSR(us->status, us->line);
-
- pr_debug("DUART INT\n");
-
- if (status & M_DUART_RX_RDY) {
- int counter = 2048;
- unsigned int ch;
-
- if (status & M_DUART_OVRUN_ERR)
- tty_insert_flip_char(tty, 0, TTY_OVERRUN);
- if (status & M_DUART_PARITY_ERR) {
- printk("Parity error!\n");
- } else if (status & M_DUART_FRM_ERR) {
- printk("Frame error!\n");
- }
-
- while (counter > 0) {
- if (!(READ_SERCSR(us->status, us->line) & M_DUART_RX_RDY))
- break;
- ch = READ_SERCSR(us->rx_hold, us->line);
- tty_insert_flip_char(tty, ch, 0);
- udelay(1);
- counter--;
- }
- tty_flip_buffer_push(tty);
- }
-
- if (status & M_DUART_TX_RDY) {
- transmit_char_pio(us);
- }
-
- return IRQ_HANDLED;
-}
-
-/*
- * Actual driver functions
- */
-
-/* Return the number of characters we can accomodate in a write at this instant */
-static int duart_write_room(struct tty_struct *tty)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
- int retval;
-
- retval = SERIAL_XMIT_SIZE - us->outp_count;
-
- pr_debug("duart_write_room called, returning %i\n", retval);
-
- return retval;
-}
-
-/* memcpy the data from src to destination, but take extra care if the
- data is coming from user space */
-static inline int copy_buf(char *dest, const char *src, int size, int from_user)
-{
- if (from_user) {
- (void) copy_from_user(dest, src, size);
- } else {
- memcpy(dest, src, size);
- }
- return size;
-}
-
-/*
- * Buffer up to count characters from buf to be written. If we don't have
- * other characters buffered, enable the tx interrupt to start sending
- */
-static int duart_write(struct tty_struct *tty, const unsigned char *buf,
- int count)
-{
- uart_state_t *us;
- int c, t, total = 0;
- unsigned long flags;
-
- if (!tty) return 0;
-
- us = tty->driver_data;
- if (!us) return 0;
-
- pr_debug("duart_write called for %i chars by %i (%s)\n", count,
- current->pid, current->comm);
-
- spin_lock_irqsave(&us->outp_lock, flags);
-
- for (;;) {
- c = count;
-
- t = SERIAL_XMIT_SIZE - us->outp_tail;
- if (t < c) c = t;
-
- t = SERIAL_XMIT_SIZE - 1 - us->outp_count;
- if (t < c) c = t;
-
- if (c <= 0) break;
-
- memcpy(us->outp_buf + us->outp_tail, buf, c);
-
- us->outp_count += c;
- us->outp_tail = (us->outp_tail + c) & (SERIAL_XMIT_SIZE - 1);
- buf += c;
- count -= c;
- total += c;
- }
-
- spin_unlock_irqrestore(&us->outp_lock, flags);
-
- if (us->outp_count && !tty->stopped &&
- !tty->hw_stopped && !(us->flags & TX_INTEN)) {
- us->flags |= TX_INTEN;
- duart_unmask_ints(us->line, M_DUART_IMR_TX);
- }
-
- return total;
-}
-
-
-/* Buffer one character to be written. If there's not room for it, just drop
- it on the floor. This is used for echo, among other things */
-static void duart_put_char(struct tty_struct *tty, u_char ch)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
- unsigned long flags;
-
- pr_debug("duart_put_char called. Char is %x (%c)\n", (int)ch, ch);
-
- spin_lock_irqsave(&us->outp_lock, flags);
-
- if (us->outp_count == SERIAL_XMIT_SIZE) {
- spin_unlock_irqrestore(&us->outp_lock, flags);
- return;
- }
-
- us->outp_buf[us->outp_tail] = ch;
- us->outp_tail = (us->outp_tail + 1) &(SERIAL_XMIT_SIZE-1);
- us->outp_count++;
-
- spin_unlock_irqrestore(&us->outp_lock, flags);
-}
-
-static void duart_flush_chars(struct tty_struct * tty)
-{
- uart_state_t *port;
-
- if (!tty)
- return;
-
- port = tty->driver_data;
-
- if (!port)
- return;
-
- if (port->outp_count <= 0 || tty->stopped || tty->hw_stopped) {
- return;
- }
-
- port->flags |= TX_INTEN;
- duart_unmask_ints(port->line, M_DUART_IMR_TX);
-}
-
-/* Return the number of characters in the output buffer that have yet to be
- written */
-static int duart_chars_in_buffer(struct tty_struct *tty)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
- int retval;
-
- retval = us->outp_count;
-
- pr_debug("duart_chars_in_buffer returning %i\n", retval);
-
- return retval;
-}
-
-/* Kill everything we haven't yet shoved into the FIFO. Turn off the
- transmit interrupt since we've nothing more to transmit */
-static void duart_flush_buffer(struct tty_struct *tty)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
- unsigned long flags;
-
- pr_debug("duart_flush_buffer called\n");
- spin_lock_irqsave(&us->outp_lock, flags);
- us->outp_head = us->outp_tail = us->outp_count = 0;
- spin_unlock_irqrestore(&us->outp_lock, flags);
-
- wake_up_interruptible(&us->tty->write_wait);
- if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) &&
- tty->ldisc.write_wakeup)
- tty->ldisc.write_wakeup(tty);
-}
-
-
-/* See sb1250 user manual for details on these registers */
-static inline void duart_set_cflag(unsigned int line, unsigned int cflag)
-{
- unsigned int mode_reg1 = 0, mode_reg2 = 0;
- unsigned int clk_divisor;
- uart_state_t *port = uart_states + line;
-
- switch (cflag & CSIZE) {
- case CS7:
- mode_reg1 |= V_DUART_BITS_PER_CHAR_7;
-
- default:
- /* We don't handle CS5 or CS6...is there a way we're supposed to
- * flag this? right now we just force them to CS8 */
- mode_reg1 |= 0x0;
- break;
- }
- if (cflag & CSTOPB) {
- mode_reg2 |= M_DUART_STOP_BIT_LEN_2;
- }
- if (!(cflag & PARENB)) {
- mode_reg1 |= V_DUART_PARITY_MODE_NONE;
- }
- if (cflag & PARODD) {
- mode_reg1 |= M_DUART_PARITY_TYPE_ODD;
- }
-
- /* Formula for this is (5000000/baud)-1, but we saturate
- at 12 bits, which means we can't actually do anything less
- that 1200 baud */
- switch (cflag & CBAUD) {
- case B200:
- case B300:
- case B1200: clk_divisor = 4095; break;
- case B1800: clk_divisor = 2776; break;
- case B2400: clk_divisor = 2082; break;
- case B4800: clk_divisor = 1040; break;
- case B9600: clk_divisor = 519; break;
- case B19200: clk_divisor = 259; break;
- case B38400: clk_divisor = 129; break;
- default:
- case B57600: clk_divisor = 85; break;
- case B115200: clk_divisor = 42; break;
- }
- WRITE_SERCSR(mode_reg1, port->mode_1, port->line);
- WRITE_SERCSR(mode_reg2, port->mode_2, port->line);
- WRITE_SERCSR(clk_divisor, port->clk_sel, port->line);
- port->last_cflags = cflag;
-}
-
-
-/* Handle notification of a termios change. */
-static void duart_set_termios(struct tty_struct *tty, struct ktermios *old)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
-
- pr_debug("duart_set_termios called by %i (%s)\n", current->pid,
- current->comm);
- if (old && tty->termios->c_cflag == old->c_cflag)
- return;
- duart_set_cflag(us->line, tty->termios->c_cflag);
-}
-
-static int get_serial_info(uart_state_t *us, struct serial_struct * retinfo)
-{
- struct serial_struct tmp;
-
- memset(&tmp, 0, sizeof(tmp));
-
- tmp.type = PORT_SB1250;
- tmp.line = us->line;
- tmp.port = UNIT_CHANREG(tmp.line,0);
- tmp.irq = UNIT_INT(tmp.line);
- tmp.xmit_fifo_size = 16; /* fixed by hw */
- tmp.baud_base = 5000000;
- tmp.io_type = SERIAL_IO_MEM;
-
- if (copy_to_user(retinfo,&tmp,sizeof(*retinfo)))
- return -EFAULT;
-
- return 0;
-}
-
-static int duart_ioctl(struct tty_struct *tty, struct file * file,
- unsigned int cmd, unsigned long arg)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
-
-/* if (serial_paranoia_check(info, tty->device, "rs_ioctl"))
- return -ENODEV;*/
- switch (cmd) {
- case TIOCMGET:
- printk("Ignoring TIOCMGET\n");
- break;
- case TIOCMBIS:
- printk("Ignoring TIOCMBIS\n");
- break;
- case TIOCMBIC:
- printk("Ignoring TIOCMBIC\n");
- break;
- case TIOCMSET:
- printk("Ignoring TIOCMSET\n");
- break;
- case TIOCGSERIAL:
- return get_serial_info(us,(struct serial_struct *) arg);
- case TIOCSSERIAL:
- printk("Ignoring TIOCSSERIAL\n");
- break;
- case TIOCSERCONFIG:
- printk("Ignoring TIOCSERCONFIG\n");
- break;
- case TIOCSERGETLSR: /* Get line status register */
- printk("Ignoring TIOCSERGETLSR\n");
- break;
- case TIOCSERGSTRUCT:
- printk("Ignoring TIOCSERGSTRUCT\n");
- break;
- case TIOCMIWAIT:
- printk("Ignoring TIOCMIWAIT\n");
- break;
- case TIOCGICOUNT:
- printk("Ignoring TIOCGICOUNT\n");
- break;
- case TIOCSERGWILD:
- printk("Ignoring TIOCSERGWILD\n");
- break;
- case TIOCSERSWILD:
- printk("Ignoring TIOCSERSWILD\n");
- break;
- default:
- break;
- }
-// printk("Ignoring IOCTL %x from pid %i (%s)\n", cmd, current->pid, current->comm);
- return -ENOIOCTLCMD;
-}
-
-/* XXXKW locking? */
-static void duart_start(struct tty_struct *tty)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
-
- pr_debug("duart_start called\n");
-
- if (us->outp_count && !(us->flags & TX_INTEN)) {
- us->flags |= TX_INTEN;
- duart_unmask_ints(us->line, M_DUART_IMR_TX);
- }
-}
-
-/* XXXKW locking? */
-static void duart_stop(struct tty_struct *tty)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
-
- pr_debug("duart_stop called\n");
-
- if (us->outp_count && (us->flags & TX_INTEN)) {
- us->flags &= ~TX_INTEN;
- duart_mask_ints(us->line, M_DUART_IMR_TX);
- }
-}
-
-/* Not sure on the semantics of this; are we supposed to wait until the stuff
- * already in the hardware FIFO drains, or are we supposed to wait until
- * we've drained the output buffer, too? I'm assuming the former, 'cause thats
- * what the other drivers seem to assume
- */
-
-static void duart_wait_until_sent(struct tty_struct *tty, int timeout)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
- unsigned long orig_jiffies;
-
- orig_jiffies = jiffies;
- pr_debug("duart_wait_until_sent(%d)+\n", timeout);
- while (!(READ_SERCSR(us->status, us->line) & M_DUART_TX_EMT)) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1);
- if (signal_pending(current))
- break;
- if (timeout && time_after(jiffies, orig_jiffies + timeout))
- break;
- }
- pr_debug("duart_wait_until_sent()-\n");
-}
-
-/*
- * duart_hangup() --- called by tty_hangup() when a hangup is signaled.
- */
-static void duart_hangup(struct tty_struct *tty)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
-
- duart_flush_buffer(tty);
- us->open = 0;
- us->tty = 0;
-}
-
-/*
- * Open a tty line. Note that this can be called multiple times, so ->open can
- * be >1. Only set up the tty struct if this is a "new" open, e.g. ->open was
- * zero
- */
-static int duart_open(struct tty_struct *tty, struct file *filp)
-{
- uart_state_t *us;
- unsigned int line = tty->index;
- unsigned long flags;
-
- if ((line >= tty->driver->num) || !sb1250_duart_present[line])
- return -ENODEV;
-
- pr_debug("duart_open called by %i (%s), tty is %p, rw is %p, ww is %p\n",
- current->pid, current->comm, tty, (void *)&tty->read_wait,
- (void *)&tty->write_wait);
-
- us = uart_states + line;
- tty->driver_data = us;
-
- spin_lock_irqsave(&open_lock, flags);
- if (!us->open) {
- us->tty = tty;
- us->tty->termios->c_cflag = us->last_cflags;
- }
- us->open++;
- us->flags &= ~TX_INTEN;
- duart_unmask_ints(line, M_DUART_IMR_RX);
- spin_unlock_irqrestore(&open_lock, flags);
-
- return 0;
-}
-
-
-/*
- * Close a reference count out. If reference count hits zero, null the
- * tty, kill the interrupts. The tty_io driver is responsible for making
- * sure we've cleared out our internal buffers before calling close()
- */
-static void duart_close(struct tty_struct *tty, struct file *filp)
-{
- uart_state_t *us = (uart_state_t *) tty->driver_data;
- unsigned long flags;
-
- pr_debug("duart_close called by %i (%s)\n", current->pid, current->comm);
-
- if (!us || !us->open)
- return;
-
- spin_lock_irqsave(&open_lock, flags);
- if (tty_hung_up_p(filp)) {
- spin_unlock_irqrestore(&open_lock, flags);
- return;
- }
-
- if (--us->open < 0) {
- us->open = 0;
- printk(KERN_ERR "duart: bad open count: %d\n", us->open);
- }
- if (us->open) {
- spin_unlock_irqrestore(&open_lock, flags);
- return;
- }
-
- spin_unlock_irqrestore(&open_lock, flags);
-
- tty->closing = 1;
-
- /* Stop accepting input */
- duart_mask_ints(us->line, M_DUART_IMR_RX);
- /* Wait for FIFO to drain */
- while (!(READ_SERCSR(us->status, us->line) & M_DUART_TX_EMT))
- ;
-
- if (tty->driver->flush_buffer)
- tty->driver->flush_buffer(tty);
- if (tty->ldisc.flush_buffer)
- tty->ldisc.flush_buffer(tty);
- tty->closing = 0;
-}
-
-
-static struct tty_operations duart_ops = {
- .open = duart_open,
- .close = duart_close,
- .write = duart_write,
- .put_char = duart_put_char,
- .flush_chars = duart_flush_chars,
- .write_room = duart_write_room,
- .chars_in_buffer = duart_chars_in_buffer,
- .flush_buffer = duart_flush_buffer,
- .ioctl = duart_ioctl,
-// .throttle = duart_throttle,
-// .unthrottle = duart_unthrottle,
- .set_termios = duart_set_termios,
- .stop = duart_stop,
- .start = duart_start,
- .hangup = duart_hangup,
- .wait_until_sent = duart_wait_until_sent,
-};
-
-/* Initialize the sb1250_duart_present array based on SOC type. */
-static void __init sb1250_duart_init_present_lines(void)
-{
- int i, max_lines;
-
- /* Set the number of available units based on the SOC type. */
- switch (soc_type) {
- case K_SYS_SOC_TYPE_BCM1x55:
- case K_SYS_SOC_TYPE_BCM1x80:
- max_lines = 4;
- break;
- default:
- /* Assume at least two serial ports at the normal address. */
- max_lines = 2;
- break;
- }
- if (max_lines > DUART_MAX_LINE)
- max_lines = DUART_MAX_LINE;
-
- for (i = 0; i < max_lines; i++)
- sb1250_duart_present[i] = 1;
-}
-
-/* Set up the driver and register it, register the UART interrupts. This
- is called from tty_init, or as a part of the module init */
-static int __init sb1250_duart_init(void)
-{
- int i;
-
- sb1250_duart_init_present_lines();
-
- sb1250_duart_driver = alloc_tty_driver(DUART_MAX_LINE);
- if (!sb1250_duart_driver)
- return -ENOMEM;
-
- sb1250_duart_driver->owner = THIS_MODULE;
- sb1250_duart_driver->name = "duart";
- sb1250_duart_driver->major = TTY_MAJOR;
- sb1250_duart_driver->minor_start = SB1250_DUART_MINOR_BASE;
- sb1250_duart_driver->type = TTY_DRIVER_TYPE_SERIAL;
- sb1250_duart_driver->subtype = SERIAL_TYPE_NORMAL;
- sb1250_duart_driver->init_termios = tty_std_termios;
- sb1250_duart_driver->flags = TTY_DRIVER_REAL_RAW;
- tty_set_operations(sb1250_duart_driver, &duart_ops);
-
- for (i = 0; i < DUART_MAX_LINE; i++) {
- uart_state_t *port = uart_states + i;
-
- if (!sb1250_duart_present[i])
- continue;
-
- init_duart_port(port, i);
- duart_mask_ints(i, M_DUART_IMR_ALL);
- if (request_irq(UNIT_INT(i), duart_int, 0, "uart", port)) {
- panic("Couldn't get uart0 interrupt line");
- }
- /*
- * this generic write to a register does not implement the 1956
- * WAR and sometimes output gets corrupted afterwards,
- * especially if the port was in use as a console.
- */
- __raw_writel(M_DUART_RX_EN|M_DUART_TX_EN, port->cmd);
-
- /*
- * we should really check to see if it's registered as a console
- * before trashing those settings
- */
- duart_set_cflag(i, port->last_cflags);
- }
-
- /* Interrupts are now active, our ISR can be called. */
-
- if (tty_register_driver(sb1250_duart_driver)) {
- printk(KERN_ERR "Couldn't register sb1250 duart serial driver\n");
- put_tty_driver(sb1250_duart_driver);
- return 1;
- }
- return 0;
-}
-
-/* Unload the driver. Unregister stuff, get ready to go away */
-static void __exit sb1250_duart_fini(void)
-{
- unsigned long flags;
- int i;
-
- local_irq_save(flags);
- tty_unregister_driver(sb1250_duart_driver);
- put_tty_driver(sb1250_duart_driver);
-
- for (i = 0; i < DUART_MAX_LINE; i++) {
- if (!sb1250_duart_present[i])
- continue;
- free_irq(UNIT_INT(i), &uart_states[i]);
- disable_irq(UNIT_INT(i));
- }
- local_irq_restore(flags);
-}
-
-module_init(sb1250_duart_init);
-module_exit(sb1250_duart_fini);
-MODULE_DESCRIPTION("SB1250 Duart serial driver");
-MODULE_AUTHOR("Broadcom Corp.");
-
-#ifdef CONFIG_SIBYTE_SB1250_DUART_CONSOLE
-
-/*
- * Serial console stuff. Very basic, polling driver for doing serial
- * console output. The console_sem is held by the caller, so we
- * shouldn't be interrupted for more console activity.
- * XXXKW What about getting interrupted by uart driver activity?
- */
-
-void serial_outc(unsigned char c, int line)
-{
- uart_state_t *port = uart_states + line;
- while (!(READ_SERCSR(port->status, line) & M_DUART_TX_RDY)) ;
- WRITE_SERCSR(c, port->tx_hold, line);
- while (!(READ_SERCSR(port->status, port->line) & M_DUART_TX_EMT)) ;
-}
-
-static void ser_console_write(struct console *cons, const char *s,
- unsigned int count)
-{
- int line = cons->index;
- uart_state_t *port = uart_states + line;
- u32 imr;
-
- imr = READ_SERCSR(port->imr, line);
- WRITE_SERCSR(0, port->imr, line);
- while (count--) {
- if (*s == '\n')
- serial_outc('\r', line);
- serial_outc(*s++, line);
- }
- WRITE_SERCSR(imr, port->imr, line);
-}
-
-static struct tty_driver *ser_console_device(struct console *c, int *index)
-{
- *index = c->index;
- return sb1250_duart_driver;
-}
-
-static int __init ser_console_setup(struct console *cons, char *str)
-{
- int i;
-
- sb1250_duart_init_present_lines();
-
- for (i = 0; i < DUART_MAX_LINE; i++) {
- uart_state_t *port = uart_states + i;
- u32 cflags = DEFAULT_CFLAGS;
-
- if (!sb1250_duart_present[i])
- continue;
-
- init_duart_port(port, i);
- if (str) {
- int speed;
- char par = 'n';
- int cbits = 8;
-
- cflags = 0;
-
- /*
- * format is in Documentation/serial_console.txt
- */
- sscanf(str, "%d%c%d", &speed, &par, &cbits);
-
- switch (speed) {
- case 200:
- case 300:
- case 1200:
- cflags |= B1200;
- break;
- case 1800:
- cflags |= B1800;
- break;
- case 2400:
- cflags |= B2400;
- break;
- case 4800:
- cflags |= B4800;
- break;
- default:
- case 9600:
- cflags |= B9600;
- break;
- case 19200:
- cflags |= B19200;
- break;
- case 38400:
- cflags |= B38400;
- break;
- case 57600:
- cflags |= B57600;
- break;
- case 115200:
- cflags |= B115200;
- break;
- }
- switch (par) {
- case 'o':
- cflags |= PARODD;
- case 'e':
- cflags |= PARENB;
- }
- switch (cbits) {
- default: // we only do 7 or 8
- case 8:
- cflags |= CS8;
- break;
- case 7:
- cflags |= CS7;
- break;
- }
- }
- duart_set_cflag(i, cflags);
- WRITE_SERCSR(M_DUART_RX_EN | M_DUART_TX_EN, port->cmd, i);
- }
-
- return 0;
-}
-
-static struct console sb1250_serial_console = {
- .name = "duart",
- .write = ser_console_write,
- .device = ser_console_device,
- .setup = ser_console_setup,
- .flags = CON_PRINTBUFFER,
- .index = -1,
-};
-
-static int __init sb1250_serial_console_init(void)
-{
- //add_preferred_console("duart", 0, "57600n8");
- register_console(&sb1250_serial_console);
- return 0;
-}
-
-console_initcall(sb1250_serial_console_init);
-
-#endif /* CONFIG_SIBYTE_SB1250_DUART_CONSOLE */
diff -up --recursive --new-file linux-mips-2.6.22-20070719.macro/include/linux/serial.h linux-mips-2.6.22-20070719/include/linux/serial.h
--- linux-mips-2.6.22-20070719.macro/include/linux/serial.h 2007-07-19 12:14:34.000000000 +0000
+++ linux-mips-2.6.22-20070719/include/linux/serial.h 2007-07-19 12:35:30.000000000 +0000
@@ -76,8 +76,7 @@ struct serial_struct {
#define PORT_16654 11
#define PORT_16850 12
#define PORT_RSA 13 /* RSA-DV II/S card */
-#define PORT_SB1250 14
-#define PORT_MAX 14
+#define PORT_MAX 13
#define SERIAL_IO_PORT 0
#define SERIAL_IO_HUB6 1
