This is a driver for SPI controller built into TXx9 MIPS SoCs.
This driver is derived from arch/mips/tx4938/toshiba_rbtx4938/spi_txx9.c.
Signed-off-by: Atsushi Nemoto <anemo@xxxxxxxxxxxxx>
---
Changes from previous version:
* Whitespace cleanup.
* spi->mode checking.
* Remove I/O barrier after gpio_set_value()
* Do not modify spi->max_speed_hz in _setup function.
* Deselect chip in _setup function.
* Check per-transfer parameters.
* Move all ndelay() into txx9spi_cs_func().
* Fix cs_change hint handling.
* Remove mapping hack, expecting ioremap() just works.
* Use the clock framework (clk_get()) instead of abusing resource framework.
* Initialize num_chipselect explicitly.
* Use platform_driver_probe() instead of platform_driver_register().
drivers/spi/Kconfig | 6 +
drivers/spi/Makefile | 1 +
drivers/spi/spi_txx9.c | 459 ++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 466 insertions(+), 0 deletions(-)
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 5e3f748..36911b6 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -156,6 +156,12 @@ config SPI_S3C24XX_GPIO
GPIO lines to provide the SPI bus. This can be used where
the inbuilt hardware cannot provide the transfer mode, or
where the board is using non hardware connected pins.
+
+config SPI_TXX9
+ tristate "Toshiba TXx9 SPI controller"
+ depends on SPI_MASTER && GENERIC_GPIO && CPU_TX49XX
+ help
+ SPI driver for Toshiba TXx9 MIPS SoCs
#
# Add new SPI master controllers in alphabetical order above this line
#
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 5788d86..7869eb5 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_SPI_MPC52xx_PSC) += mpc52xx_psc_spi.o
obj-$(CONFIG_SPI_MPC83xx) += spi_mpc83xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx.o
+obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
diff --git a/drivers/spi/spi_txx9.c b/drivers/spi/spi_txx9.c
new file mode 100644
index 0000000..fd6a939
--- /dev/null
+++ b/drivers/spi/spi_txx9.c
@@ -0,0 +1,459 @@
+/*
+ * spi_txx9.c - TXx9 SPI controller driver.
+ *
+ * Based on linux/arch/mips/tx4938/toshiba_rbtx4938/spi_txx9.c
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ *
+ * 2003-2005 (c) MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is
+ * licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ * Support for TX4938 in 2.6 - Manish Lachwani (mlachwani@xxxxxxxxxx)
+ *
+ * Convert to generic SPI framework - Atsushi Nemoto (anemo@xxxxxxxxxxxxx)
+ */
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/workqueue.h>
+#include <linux/spi/spi.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <asm/gpio.h>
+
+
+#define SPI_FIFO_SIZE 4
+
+#define TXx9_SPMCR 0x00
+#define TXx9_SPCR0 0x04
+#define TXx9_SPCR1 0x08
+#define TXx9_SPFS 0x0c
+#define TXx9_SPSR 0x14
+#define TXx9_SPDR 0x18
+
+/* SPMCR : SPI Master Control */
+#define TXx9_SPMCR_OPMODE 0xc0
+#define TXx9_SPMCR_CONFIG 0x40
+#define TXx9_SPMCR_ACTIVE 0x80
+#define TXx9_SPMCR_SPSTP 0x02
+#define TXx9_SPMCR_BCLR 0x01
+
+/* SPCR0 : SPI Control 0 */
+#define TXx9_SPCR0_TXIFL_MASK 0xc000
+#define TXx9_SPCR0_RXIFL_MASK 0x3000
+#define TXx9_SPCR0_SIDIE 0x0800
+#define TXx9_SPCR0_SOEIE 0x0400
+#define TXx9_SPCR0_RBSIE 0x0200
+#define TXx9_SPCR0_TBSIE 0x0100
+#define TXx9_SPCR0_IFSPSE 0x0010
+#define TXx9_SPCR0_SBOS 0x0004
+#define TXx9_SPCR0_SPHA 0x0002
+#define TXx9_SPCR0_SPOL 0x0001
+
+/* SPSR : SPI Status */
+#define TXx9_SPSR_TBSI 0x8000
+#define TXx9_SPSR_RBSI 0x4000
+#define TXx9_SPSR_TBS_MASK 0x3800
+#define TXx9_SPSR_RBS_MASK 0x0700
+#define TXx9_SPSR_SPOE 0x0080
+#define TXx9_SPSR_IFSD 0x0008
+#define TXx9_SPSR_SIDLE 0x0004
+#define TXx9_SPSR_STRDY 0x0002
+#define TXx9_SPSR_SRRDY 0x0001
+
+
+struct txx9spi {
+ struct workqueue_struct *workqueue;
+ struct work_struct work;
+ spinlock_t lock; /* protect 'queue' */
+ struct list_head queue;
+ wait_queue_head_t waitq;
+ void __iomem *membase;
+ int irq;
+ int baseclk;
+ struct clk *clk;
+ u32 max_speed_hz, min_speed_hz;
+ int last_chipselect;
+ int last_chipselect_val;
+};
+
+static u32 txx9spi_rd(struct txx9spi *c, int reg)
+{
+ return __raw_readl(c->membase + reg);
+}
+static void txx9spi_wr(struct txx9spi *c, u32 val, int reg)
+{
+ __raw_writel(val, c->membase + reg);
+}
+
+static void txx9spi_cs_func(struct spi_device *spi, struct txx9spi *c,
+ int on, unsigned int cs_delay)
+{
+ int val = (spi->mode & SPI_CS_HIGH) ? on : !on;
+ if (on) {
+ /* deselect the chip with cs_change hint in last transfer */
+ if (c->last_chipselect >= 0)
+ gpio_set_value(c->last_chipselect,
+ !c->last_chipselect_val);
+ c->last_chipselect = spi->chip_select;
+ c->last_chipselect_val = val;
+ } else {
+ c->last_chipselect = -1;
+ ndelay(cs_delay); /* CS Hold Time */
+ }
+ gpio_set_value(spi->chip_select, val);
+ ndelay(cs_delay); /* CS Setup Time / CS Recovery Time */
+}
+
+/* the spi->mode bits understood by this driver: */
+#define MODEBITS (SPI_CS_HIGH|SPI_CPOL|SPI_CPHA)
+
+static int txx9spi_setup(struct spi_device *spi)
+{
+ struct txx9spi *c = spi_master_get_devdata(spi->master);
+ u8 bits_per_word;
+
+ if (spi->mode & ~MODEBITS)
+ return -EINVAL;
+
+ if (!spi->max_speed_hz ||
+ spi->max_speed_hz > c->max_speed_hz ||
+ spi->max_speed_hz < c->min_speed_hz)
+ return -EINVAL;
+
+ bits_per_word = spi->bits_per_word ?: 8;
+ if (bits_per_word != 8 && bits_per_word != 16)
+ return -EINVAL;
+
+ if (gpio_direction_output(spi->chip_select,
+ !(spi->mode & SPI_CS_HIGH))) {
+ dev_err(&spi->dev, "Cannot setup GPIO for chipselect.\n");
+ return -EINVAL;
+ }
+
+ /* deselect chip */
+ spin_lock(&c->lock);
+ txx9spi_cs_func(spi, c, 0, 1000000000 / 2 / spi->max_speed_hz);
+ spin_unlock(&c->lock);
+
+ return 0;
+}
+
+static irqreturn_t txx9spi_interrupt(int irq, void *dev_id)
+{
+ struct txx9spi *c = dev_id;
+
+ /* disable rx intr */
+ txx9spi_wr(c, txx9spi_rd(c, TXx9_SPCR0) & ~TXx9_SPCR0_RBSIE,
+ TXx9_SPCR0);
+ wake_up(&c->waitq);
+ return IRQ_HANDLED;
+}
+
+static int txx9spi_work_one(struct txx9spi *c, struct spi_message *m)
+{
+ struct spi_device *spi = m->spi;
+ struct spi_transfer *t;
+ unsigned int cs_delay;
+ unsigned int cs_change;
+ int status;
+ u32 mcr;
+ u8 bits_per_word = spi->bits_per_word ?: 8;
+ u32 speed_hz = 0, n;
+
+ /* check each transter parameters */
+ list_for_each_entry (t, &m->transfers, transfer_list) {
+ if (!t->tx_buf && !t->rx_buf && t->len)
+ return -EINVAL;
+ if (t->bits_per_word && t->bits_per_word != bits_per_word)
+ return -EINVAL;
+ if (t->len & ((bits_per_word >> 3) - 1))
+ return -EINVAL;
+ if (!speed_hz)
+ speed_hz = t->speed_hz;
+ else if (speed_hz != t->speed_hz)
+ return -EINVAL;
+ }
+ if (!speed_hz)
+ speed_hz = spi->max_speed_hz;
+ if (!speed_hz || speed_hz > c->max_speed_hz)
+ speed_hz = c->max_speed_hz;
+ else if (speed_hz < c->min_speed_hz)
+ return -EINVAL;
+ n = (c->baseclk + speed_hz - 1) / speed_hz;
+ if (n < 1)
+ n = 1;
+ else if (n > 0xff)
+ n = 0xff;
+
+ mcr = txx9spi_rd(c, TXx9_SPMCR);
+ if (unlikely((mcr & TXx9_SPMCR_OPMODE) == TXx9_SPMCR_ACTIVE)) {
+ dev_err(&spi->dev, "Bad mode.\n");
+ return -EIO;
+ }
+
+ /* enter config mode */
+ mcr &= ~(TXx9_SPMCR_OPMODE | TXx9_SPMCR_SPSTP | TXx9_SPMCR_BCLR);
+ txx9spi_wr(c, mcr | TXx9_SPMCR_CONFIG | TXx9_SPMCR_BCLR, TXx9_SPMCR);
+ txx9spi_wr(c, TXx9_SPCR0_SBOS |
+ ((spi->mode & SPI_CPOL) ? TXx9_SPCR0_SPOL : 0) |
+ ((spi->mode & SPI_CPHA) ? TXx9_SPCR0_SPHA : 0) |
+ 0x08,
+ TXx9_SPCR0);
+ txx9spi_wr(c, (n << 8) | bits_per_word, TXx9_SPCR1);
+ /* enter active mode */
+ txx9spi_wr(c, mcr | TXx9_SPMCR_ACTIVE, TXx9_SPMCR);
+
+ cs_change = 1;
+ status = 0;
+ /* CS setup/hold/recovery time in nsec */
+ cs_delay = 100 + 1000000000 / 2 / speed_hz;
+ list_for_each_entry (t, &m->transfers, transfer_list) {
+ const void *txbuf = t->tx_buf;
+ void *rxbuf = t->rx_buf;
+ u32 data;
+ unsigned int len = t->len;
+ unsigned int wsize = bits_per_word >> 3; /* in bytes */
+
+ if (cs_change)
+ txx9spi_cs_func(spi, c, 1, cs_delay);
+ cs_change = t->cs_change;
+ while (len) {
+ unsigned int count = SPI_FIFO_SIZE;
+ int i;
+ u32 cr0;
+ if (len < count * wsize)
+ count = len / wsize;
+ /* now tx must be idle... */
+ while (!(txx9spi_rd(c, TXx9_SPSR) & TXx9_SPSR_SIDLE))
+ ;
+ cr0 = txx9spi_rd(c, TXx9_SPCR0);
+ cr0 &= ~TXx9_SPCR0_RXIFL_MASK;
+ cr0 |= (count - 1) << 12;
+ /* enable rx intr */
+ cr0 |= TXx9_SPCR0_RBSIE;
+ txx9spi_wr(c, cr0, TXx9_SPCR0);
+ /* send */
+ for (i = 0; i < count; i++) {
+ if (txbuf) {
+ data = wsize == 1 ?
+ *(const u8 *)txbuf :
+ *(const u16 *)txbuf;
+ txx9spi_wr(c, data, TXx9_SPDR);
+ txbuf += wsize;
+ } else
+ txx9spi_wr(c, 0, TXx9_SPDR);
+ }
+ /* wait all rx data */
+ wait_event(c->waitq,
+ txx9spi_rd(c, TXx9_SPSR) & TXx9_SPSR_RBSI);
+ /* receive */
+ for (i = 0; i < count; i++) {
+ data = txx9spi_rd(c, TXx9_SPDR);
+ if (rxbuf) {
+ if (wsize == 1)
+ *(u8 *)rxbuf = data;
+ else
+ *(u16 *)rxbuf = data;
+ rxbuf += wsize;
+ }
+ }
+ len -= count * wsize;
+ }
+ m->actual_length += t->len;
+ if (t->delay_usecs)
+ udelay(t->delay_usecs);
+
+ if (!cs_change)
+ continue;
+ if (t->transfer_list.next == &m->transfers)
+ break;
+ /* sometimes a short mid-message deselect of the chip
+ * may be needed to terminate a mode or command
+ */
+ txx9spi_cs_func(spi, c, 0, cs_delay);
+ }
+
+ m->status = status;
+ m->complete(m->context);
+
+ /* normally deactivate chipselect ... unless no error and
+ * cs_change has hinted that the next message will probably
+ * be for this chip too.
+ */
+ if (!(status == 0 && cs_change))
+ txx9spi_cs_func(spi, c, 0, cs_delay);
+
+ /* enter config mode */
+ txx9spi_wr(c, mcr | TXx9_SPMCR_CONFIG | TXx9_SPMCR_BCLR, TXx9_SPMCR);
+ return status;
+}
+
+static void txx9spi_work(struct work_struct *work)
+{
+ struct txx9spi *c = container_of(work, struct txx9spi, work);
+ unsigned long flags;
+
+ spin_lock_irqsave(&c->lock, flags);
+ while (!list_empty(&c->queue)) {
+ struct spi_message *m;
+
+ m = container_of(c->queue.next, struct spi_message, queue);
+ list_del_init(&m->queue);
+ spin_unlock_irqrestore(&c->lock, flags);
+
+ txx9spi_work_one(c, m);
+
+ spin_lock_irqsave(&c->lock, flags);
+ }
+ spin_unlock_irqrestore(&c->lock, flags);
+}
+
+static int txx9spi_transfer(struct spi_device *spi, struct spi_message *m)
+{
+ struct spi_master *master = spi->master;
+ struct txx9spi *c = spi_master_get_devdata(master);
+ unsigned long flags;
+
+ m->actual_length = 0;
+ spin_lock_irqsave(&c->lock, flags);
+ list_add_tail(&m->queue, &c->queue);
+ queue_work(c->workqueue, &c->work);
+ spin_unlock_irqrestore(&c->lock, flags);
+
+ return 0;
+}
+
+static int __init txx9spi_probe(struct platform_device *dev)
+{
+ struct spi_master *master;
+ struct txx9spi *c;
+ struct resource *res;
+ int ret = -ENODEV;
+ u32 mcr;
+
+ master = spi_alloc_master(&dev->dev, sizeof(*c));
+ if (!master)
+ return ret;
+ c = spi_master_get_devdata(master);
+ c->irq = -1;
+ platform_set_drvdata(dev, master);
+
+ INIT_WORK(&c->work, txx9spi_work);
+ spin_lock_init(&c->lock);
+ INIT_LIST_HEAD(&c->queue);
+ init_waitqueue_head(&c->waitq);
+
+ c->clk = clk_get(&dev->dev, "spi-baseclk");
+ if (IS_ERR(c->clk)) {
+ ret = PTR_ERR(c->clk);
+ c->clk = NULL;
+ goto exit;
+ }
+ if (clk_enable(c->clk)) {
+ clk_put(c->clk);
+ c->clk = NULL;
+ goto exit;
+ }
+ c->baseclk = clk_get_rate(c->clk);
+ c->min_speed_hz = (c->baseclk + 0xff - 1) / 0xff;
+ c->max_speed_hz = c->baseclk;
+
+ res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ if (!res)
+ goto exit;
+ c->membase = ioremap(res->start, res->end - res->start + 1);
+ if (!c->membase)
+ goto exit;
+
+ /* enter config mode */
+ mcr = txx9spi_rd(c, TXx9_SPMCR);
+ mcr &= ~(TXx9_SPMCR_OPMODE | TXx9_SPMCR_SPSTP | TXx9_SPMCR_BCLR);
+ txx9spi_wr(c, mcr | TXx9_SPMCR_CONFIG | TXx9_SPMCR_BCLR, TXx9_SPMCR);
+
+ c->irq = platform_get_irq(dev, 0);
+ if (c->irq < 0)
+ goto exit;
+ ret = request_irq(c->irq, txx9spi_interrupt, 0, dev->name, c);
+ if (ret) {
+ c->irq = -1;
+ goto exit;
+ }
+
+ c->workqueue = create_singlethread_workqueue(master->cdev.dev->bus_id);
+ if (!c->workqueue)
+ goto exit;
+ c->last_chipselect = -1;
+
+ dev_info(&dev->dev, "at %#llx, irq %d, %dMHz\n",
+ (unsigned long long)res->start, c->irq,
+ (c->baseclk + 500000) / 1000000);
+
+ master->bus_num = dev->id;
+ master->setup = txx9spi_setup;
+ master->transfer = txx9spi_transfer;
+ master->num_chipselect = 0; /* unlimited: any GPIO numbers */
+
+ ret = spi_register_master(master);
+ if (ret)
+ goto exit;
+ return 0;
+exit:
+ if (c->workqueue)
+ destroy_workqueue(c->workqueue);
+ if (c->irq >= 0)
+ free_irq(c->irq, c);
+ if (c->membase)
+ iounmap(c->membase);
+ if (c->clk) {
+ clk_disable(c->clk);
+ clk_put(c->clk);
+ }
+ platform_set_drvdata(dev, NULL);
+ spi_master_put(master);
+ return ret;
+}
+
+static int __exit txx9spi_remove(struct platform_device *dev)
+{
+ struct spi_master *master = spi_master_get(platform_get_drvdata(dev));
+ struct txx9spi *c = spi_master_get_devdata(master);
+
+ spi_unregister_master(master);
+ platform_set_drvdata(dev, NULL);
+ destroy_workqueue(c->workqueue);
+ free_irq(c->irq, c);
+ iounmap(c->membase);
+ clk_disable(c->clk);
+ clk_put(c->clk);
+ spi_master_put(master);
+ return 0;
+}
+
+static struct platform_driver txx9spi_driver = {
+ .remove = __exit_p(txx9spi_remove),
+ .driver = {
+ .name = "txx9spi",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init txx9spi_init(void)
+{
+ return platform_driver_probe(&txx9spi_driver, txx9spi_probe);
+}
+subsys_initcall(txx9spi_init);
+
+static void __exit txx9spi_exit(void)
+{
+ platform_driver_unregister(&txx9spi_driver);
+}
+module_exit(txx9spi_exit);
+
+MODULE_DESCRIPTION("TXx9 SPI Driver");
+MODULE_LICENSE("GPL");
