Hi,
I cant build the kernel with this patch -- i m using the 2.6.14.6
kernel..
also, the kernel does not hang, but the output produced on the console
is not complete: eg
i.e. I get this:
> 1000 i 1.5 P P <v@e.>
> 0: A1 Er n 01500000, 28
> 0: Bd BCM5221 10/100 BT PHY e 0
> 0: U Bo BCM5221 10/100 BT PHY a
> 1: A1 Ee 01510000, 29
> 1: Bm BCM5221 10/100 BT PHY e 0
> 1: U Bc BCM5221 10/100 BT PHY l
> NET: Re c l 2
> IP t h l i: 1024 (: 0, 4096 s)
> TCP l h i: 4096 (: 2, 16384 s)
> TCP d h i: 4096 (: 2, 16384 s)
> TCP: H s u (a 4096 4096)
> TCP s
> TCP s
> NET: Rs o y 1
> NET: Rt o i 17
> IP-C: Gn s 255.255.255.0
instead of :
> au1000eth version 1.5 Pete Popov <ppopov@xxxxxxxxxxxxxxxxx>
> eth0: Au1x Ethernet found at 0xb1500000, irq 28
> eth0: Broadcom BCM5221 10/100 BaseT PHY at phy address 0
> eth0: Using Broadcom BCM5221 10/100 BaseT PHY as default
> eth1: Au1x Ethernet found at 0xb1510000, irq 29
> eth1: Broadcom BCM5221 10/100 BaseT PHY at phy address 0
> eth1: Using Broadcom BCM5221 10/100 BaseT PHY as default
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 2, 16384 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> IP-Config: Guessing netmask 255.255.255.0
> IP-Config: Complete:
which makes me think there is some kind of a wrong initialisation of the UART -- but i ve checked all the parameters:
iobase, IRQ, etc and nothing is obviously wrong --
I was wondering what the significance of the flags in the plat_serial8250_port is?
> static struct plat_serial8250_port encm3_via_uart_data[] = {
> {
>
> .flags = UPF_SHARE_IRQ,
>
Thanks and Regards,
Ashlesha.
On Thu, 2006-12-07 at 10:37 +0900, Atsushi Nemoto wrote:
> On Wed, 06 Dec 2006 16:13:23 -0800, Ashlesha Shintre <ashlesha@xxxxxxxxxx> wrote:
> > However, I now get a "Cant analyze prologue code at 80294aec." error!
> >
> > Any remedies/suggestions for the same?
>
> Please look at this thread:
>
> http://www.linux-mips.org/archives/linux-mips/2004-09/msg00123.html
>
> Final patch is:
>
> http://www.linux-mips.org/archives/linux-mips/2004-10/msg00312.html
>
> And actual commit is:
>
> http://www.linux-mips.org/git?p=linux.git;a=commitdiff;h=dc953df1ba5526814982676f47580c8e1bcdbfeb
>
> ---
> Atsushi Nemoto
