We faced a similar problem on 2.6.14
kernel (on AU1100 board) where the keyboard is detected, but the keystrokes
don’t appear on the serial console. Our thinking was that additional
support/application is required to interface with the HID driver, to re-direct
keystrokes onto console.
Hemanth
From: linux-mips-bounce@xxxxxxxxxxxxxx
[mailto:linux-mips-bounce@xxxxxxxxxxxxxx] On
Behalf Of chandrashekar mogilicherla
Sent: Tuesday, November 28, 2006
12:41 PM
To: linux-mips@xxxxxxxxxxxxxx;
Puneet
Subject: USB keyboard not getting
handled???????
Iam using a device with linux 2.6.11 kernel running on mips arch.
I have got a problem trying to enable usb keyboard on my device.
When i enable following options in kernel config
USB_CONFIG
ohci, ehci
hid or boot hid
keyboard in input
devices
USB keyboard is detected . It is shown in /proc/bus/usb/devices , drivers are
loaded. But keyboard is not working.
Following is the mesg log i get when i enabled usb feaures in kernel,
------------------------------------------------------------------------------------------------
In ehci_hcd_au1xxx_drv_probe
drivers/usb/host/ehci-au1xxx.c: starting Au1xxx EHCI USB Controller
drivers/usb/host/ehci-au1xxx.c: Clock to USB host has been enabled
au1xxx-ehci au1xxx-ehci0: reset hcs_params 0x1212 dbg=0 cc=1 pcc=2 ordered
ports=2
au1xxx-ehci au1xxx-ehci0: reset hcc_params 0012 thresh 1 uframes 256/512/1024
ehci_hcd (Au1xxx) at 0xb4020200, irq 29
au1xxx-ehci au1xxx-ehci0: new USB bus registered, assigned bus number 1
au1xxx-ehci au1xxx-ehci0: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
au1xxx-ehci au1xxx-ehci0: init command 010009 (park)=0 ithresh=1 period=256 RUN
au1xxx-ehci au1xxx-ehci0: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: Au1xxx EHCI
usb usb1: Manufacturer: Linux 2.6.11 ehci_hcd
usb usb1: SerialNumber: au1xxx
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (Au1xxx)
block sizes: ed 64 td 64
hub 1-0:1.0: state 5 ports 2 chg 0006 evt 0007
au1xxx-ehci au1xxx-ehci0: GetStatus port 1 status 001403 POWER sig=k CSC
CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
In ohci_hcd_au1xxx_drv_probe
drivers/usb/host/ohci-au1xxx.c: starting Au1xxx OHCI USB Controller
drivers/usb/host/ohci-au1xxx.c: Clock to USB host has been enabled
ohci_hcd (Au1xxx) at 0xb4020100, irq 29
au1xxx-ohci au1xxx-ohci0: new USB bus registered, assigned bus number 2
au1xxx-ohci au1xxx-ohci0: ohci_au1xxx_start, ohci:86e9fcf0
au1xxx-ohci au1xxx-ohci0: resetting from state 'reset', control = 0x0
au1xxx-ohci au1xxx-ohci0: OHCI controller state
au1xxx-ohci au1xxx-ohci0: OHCI 1.0, with legacy support registers
au1xxx-ohci au1xxx-ohci0: control 0x083 HCFS=operational CBSR=3
au1xxx-ohci au1xxx-ohci0: cmdstatus 0x00000 SOC=0
au1xxx-ohci au1xxx-ohci0: intrstatus 0x00000044 RHSC SF
au1xxx-ohci au1xxx-ohci0: intrenable 0x8000001a MIE UE RD WDH
au1xxx-ohci au1xxx-ohci0: hcca frame #0021
au1xxx-ohci au1xxx-ohci0: roothub.a 10000202 POTPGT=16 NPS NDP=2
au1xxx-ohci au1xxx-ohci0: roothub.b 00000000 PPCM=0000 DR=0000
au1xxx-ohci au1xxx-ohci0: roothub.status 00008000 DRWE
au1xxx-ohci au1xxx-ohci0: roothub.portstatus [0] 0x00000100 PPS
au1xxx-ohci au1xxx-ohci0: roothub.portstatus [1] 0x00000100 PPS
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: Au1xxx OHCI
usb usb2: Manufacturer: Linux 2.6.11 ohci_hcd
usb usb2: SerialNumber: au1xxx
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 32ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
au1xxx-ehci au1xxx-ehci0: port 1 low speed --> companion
au1xxx-ohci au1xxx-ohci0: created debug files
Initializing USB Mass Storage driver...
au1xxx-ehci au1xxx-ehci0: GetStatus port 1 status 003002 POWER OWNER
sig=se0 CSC
hub 1-0:1.0: port 2, status 0100, change 0000, 12 Mb/s
hub 2-0:1.0: state 5 ports 2 chg 0006 evt 0007
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
au1xxx-ohci au1xxx-ohci0: GetStatus roothub.portstatus [0] = 0x00010301 CSC
LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
au1xxx-ohci au1xxx-ohci0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC
LSDA PPS PES CCS
usb 2-1: new low speed USB device using au1xxx-ohci and address 2
ghzhang: USB inserted
au1xxx-ohci au1xxx-ohci0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC
LSDA PPS PES CCS
usb 2-1: skipped 1 descriptor after interface
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
usb 2-1: Product: HP Basic USB Keyboard
usb 2-1: Manufacturer: CHICONY
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
hub 2-0:1.0: port 2, status 0100, change 0000, 12 Mb/s
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0002
usbhid 2-1:1.0: usb_probe_interface
usbhid 2-1:1.0: usb_probe_interface - got id
input: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-au1xxx-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2
(2004/08/27)
usbcore: registered new driver rtl8150
usbcore: registered new driver usblcd
drivers/usb/misc/usblcd.c: USBLCD Driver Version 1.04 (C) Adams IT Services http://www.usblcd.de
drivers/usb/misc/usblcd.c: USBLCD support registered.
usbcore: registered new driver usbled
usbcore: registered new driver usbtest
-----------------------------------------------------------------------------------------------------
cat /proc/bus/input/devices
I: Bus=0003 Vendor=03f0 Product=0024 Version=0300
N: Name="CHICONY HP Basic USB Keyboard"
P: Phys=usb-au1xxx-1/input0
H: Handlers=event0
B: EV=120013
B: KEY=10000 7 ff87207a c14057ff febeffdf ffefffff ffffffff fffffffe
B: MSC=10
B: LED=7
----------------------------------------------------------------------------
CAN ANYBODY HELP ME IN THIS REGARD,
Is there anything to do with "keybdev" and "/sbin/hotplug"?????
Both of these are not present on my system
Thanking you in advance,
M.Chandrashekar
